金属－橡胶硫化粘接过程中分子取向行为的间接证据

对金属－橡胶热硫化粘接复合体的剥离行为进行了研究，同一粘接试样的双向１８０°剥离试验显示出了巨大的差异。本文分析了弹性材料在硫化过程中的分子行为，并提出了相应的新假设，认为这是由于金属－橡胶在硫化粘接过程中分子取向交联行为所致。这种双向１８０°剥离破坏现象可被看作是金属－橡胶硫化粘接过程中分子取向行为的间接证据。     

Molecular orientation and stress in biaxially deformed polymers. II. Steady potential flow

The development of biaxial segmental orientation and stress in a flexible-chain polymer fluid subjected to steady biaxial extensional flow is analyzed. Closed-formula model based on the Padè approximation of the inverse Langevin function in the non-Gaussian distribution of the chain end-to-end vectors is considered. The approach is free from the limitations related to finite chain extensibility and slow convergence of the series expansion formulations at higher chain deformations.Segmental orientation is characterized by the average orientation tensor, related axial orientation factors and global orientation anisotropy. Orientational behavior and corresponding stresses in the biaxial elongational potential flow are discussed in a wide range of elongation rates. Orientation characteristics calculated for the biaxial flow deformation are much higher than those predicted for the affine biaxial stretch deformation in polymer solids.     

Political orientation and modern versus aversive racism: Tests of Dovidio and Gaertner's (1998) integrated model.

According to J. F. Dovidio and S. L. Gaertner's (1998) integrated model of racism, politically liberal European Americans tend to express racism differently than conservative European Americans, with liberals demonstrating aversive racism and conservatives, symbolic or modern racism. In support of the model, in Experiment 1 liberals showed bias in favor of a twice-prosecuted African American relative to a European American in their judgment of double jeopardy, whereas conservatives did the reverse. Experiment 2 replicated these effects while eliminating a confound in the design of Experiment 1. Experiment 3 found evidence for the intrapsychic conflict hypothesized to underlie aversive racism. Specifically, only liberals displayed greater physiological arousal to the touch of an African American versus a European American experimenter. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Olfactory recognition of nonhosts aspen and birch by conifer bark beetlesTomicus piniperda andHylurgops palliatus

The field response ofTomicus piniperda (L.) andHylurgops palliatus (Gyll.) (Coleoptera: Scolytidae) to the attractant ethanol in combination with volatile wood constituents released from the nonhost tree speciesPopulus tremula L. (Salicaceae) andBetula pendula Roth (Betulaceae) was studied using flight barrier traps. The attraction of both species decreased when aspen or birch wood was added to the ethanol bait. The same was true forRhizophagus depressus (F.) (Coleoptera: Rhizophagidae), a predatory species associated with conifer bark beetles.Glischrochilus quadripunctatus (L-),Epuraea bickhardti St.-Claire Deville,E. unicolor (Oliv.) (Coleoptera: Nitidulidae), andRhizophagus parvutus (Payk.) (Coleoptera: Rhizophagidae) were caught in higher numbers in traps baited with both ethanol and wood of aspen or birch than in traps baited with ethanol alone. In a separate experiment, landings ofT. piniperda andH. palliatus on nonhosts (black plastic tubes) were demonstrated with sticky traps.     

甲苯定向氯化合成对氯甲苯

采用天然沸石作为甲苯氯化催化剂再加入助催化剂,进行甲苯氯化反应研究,探讨氯化工艺及各因素的影响,结果表明,甲苯转化率达到99.7%,一氯甲苯产物中55%为对氯甲苯.     

Thermally stimulated shrinkage forces in oriented polymers: 1. Temperature dependence

Temperature dependences of shrinkage forces appearing in oriented polymer samples when heated at constant length were recorded for polycarbonate, polyethylene terephthalate, polyethylene and polypropylene. The influence of various processing conditions on thermally stimulated shrinkage forces is demonstrated. A four-state model is proposed which qualitatively describes the temperature dependences of shrinkage forces in amorphous polymers.     

Nonepitaxial Orientation in Sol–Gel Bismuth Titanate Films

Control over crystallographic orientation in ceramic thin films is important for highly anisotropic structures. Layered perovskites, like Bi₄Ti₃O₁₂, have interesting properties associated with their ferroelectric nature, which may be fully exploited only when films are highly textured. Textured films of this titanate were fabricated via a sol–gel technique without using epitaxial growth. Orientation in the film is confirmed by XRD and SEM, and supported by refractive index and dielectric measurements. In an attempt to explain the orienting effect, light scattering experiments were conducted to yield information about the molecular size, shape, and conformation of macromolecules as the sol–gel solution ages and condensation reactions proceed. These experiments clearly show an increase in the size of molecular clusters with time. We believe that it is the organization of these large clusters during spin coating, and the relationship of the backbone chemistry to the crystal structure of Bi₄Ti₃O₁₂, that are responsible for the observed orientation.     

Structure and properties of injection‐molded polypropylenes with different molecular weight distribution and tacticity characteristics

Two series of polypropylenes with different molecular weight distribution and tacticity characteristics were injection molded into flexural test specimens by varying cylinder temperature and the effects of the molecular weight distribution and tacticity on the structure and properties of the moldings were studied. Measured propertied were flexural modulus, flexural strength, heat distortion temperature, Izod impact strength, and mold shrinkage and structures studied were crystallinity, the thickness of skin layer, a*‐axis‐oriented component fraction and crystalline orientation functions. The relations between the structures and properties were also studied. It was found that the molecular weight distribution and tacticity characteristics affect the properties mainly through the molecular orientation and crystallinity, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2142–2156, 2002     

制造业中、高级职业技术教育刍议

论述了制造业中、高级岗位职业技术教育的意义、现状、存在问题及其人才市场要求，探讨了办好制造业职业技术教育的几个关键问题。