排序方式: 共有81条查询结果,搜索用时 78 毫秒
21.
22.
工作性对负温防冻剂混凝土性能的影响 总被引:1,自引:0,他引:1
在混凝土冬季施工中,防冻剂通常被加到混凝土以保证低温下强度的持续发展.JC475-92防冻剂标准中规定基准混凝土的坍落度通常控制在(30±10)mm.然而,越来越多的大坍落度的混凝土或自密实混凝土被广泛应用于冬季混凝土施工.因此,探讨了掺与未掺防冻剂的不同坍落度混凝土强度的变化规律.当水灰比固定而用高效减水剂提高坍落度时,减水刺对常温下混凝土的影响可以忽略,但对负温度下混凝土强度的影响明显.负温度混凝土强度随着坍落度的增加而降低,其原因是高效减水剂延长了水泥的凝结时间,并易造成混凝土早期的冻害. 相似文献
23.
24.
25.
26.
负温防冻剂混凝土的界面显微结构与性能 总被引:4,自引:0,他引:4
研究了不同种类的防冻剂、矿物掺合料对正、负温下水泥净浆、砂浆及混凝土力学性能的影响.通过对比实验表明:水泥净浆、砂浆及混凝土在正、负温条件下抗压强度的变化规律存在显著差异,这取决于其内部显微结构,尤其是界面显微结构的差异.利用显微硬度计、扫描电镜、能谱分析、X射线衍射研究了防冻剂混凝土界面过渡区的范围、元素分布、钙硅比及氢氧化钙的取向度.结果表明:防冻剂能够改善负温下混凝土的界面显微结构,防冻剂和矿物掺合料的复合使用可为负温混凝土提供理想的界面显微结构. 相似文献
27.
研究养护温度对高延性水泥基复合材料性能的影响,分析养护温度在20、40、60和80℃时水泥基复合材料的抗弯性能、抗压强度、抗折强度及裂缝分布特点.结果表明,养护温度越高,高延性水泥基复合材料的早期跨中挠度越小;养护温度高于40℃时,试件的跨中挠度和韧性指数随龄期延长无明显变化;高养护温度能显著提高高延性水泥基复合材料的早期抗压强度和抗折强度,龄期对高温养护条件下高延性水泥基复合材料的抗压、抗折强度影响不大;粉煤灰掺量相同时,常温养护下高延性水泥基复合材料的裂缝更加细密均匀;养护温度为60℃时,粉煤灰掺量提高至80%,高延性水泥基复合材料的韧性显著提高,28d抗压强度可达70MPa. 相似文献
28.
杨英姿 《武汉理工大学学报(材料科学英文版)》2010,(2)
The effects of water/binder ratio (w/b) on the toughness behavior, compressive strength and flexural strength of engineered cementitious composites (ECC) were investigated. The w/b ratios of 0.25, 0.31, 0.33 and 0.37 were selected and the specimens were tested at the ages of 7 d and 28 d. The experimental results showed that there was a corresponding increase in first cracking strength, modulus of rupture, compressive strength and flexural strength with the decrease of w/b. Within the w/b range of 0.25-0.37... 相似文献
29.
杨英姿 《哈尔滨工业大学学报》2009,41(6):43-47
为实现寒冷地区冬季施工中混凝土内部结构发展的无损监测,研究两种坍落度、两种防冻剂的混凝土在标准养护条件、恒负温养护条件及自然变负温养护下动弹性模量随龄期的变化规律.结果表明:标准养护条件下,高掺量防冻盐类的掺入给混凝土内部结构带来一定的损伤.在负温阶段,异常高的混凝土动弹性模量值是由混凝土内部含冰量所决定的.通过转入正温一定时间内动弹性模量的衰减值可以判断混凝土在负温阶段受冻损伤程度.转入正温条件下混凝土的动弹性模量的发展规律与混凝土强度发展规律是一致的.因此,这一无损检测方法可以应用于冬季施工中. 相似文献
30.
Fly ash used as the main raw materials,incorporated with sintering expansion additive and fluxing additive in different ratio,was sintered high-strength lightweight aggregates of fly ash (ceramsite) in the laboratory-controlled electric furnace.The results show that the optimal sintering system is the sintering temperature range of 1250 ℃ to 1280 ℃ and retaining time of 5 min-10 min.The bulk density,the apparent density and 24 h water absorption of ceramsites decrease with the increase of sintering additive and the decrease of the amount of fly ash.The addition of fluxing additive can significantly enhance the compressive strength of ceramsite pellets,reduce its water absorption at 24 h and improve pore-shape ofinner structure.The firing coefficient (Pk) changed within 7.8-8.1 of raw materials can prepare high strength and low water absorption ceramsites.Pk kept a good linear relationship with porosity and strength of ceramsite particles. 相似文献