Mechanical behavior of electrochemically hydrogenated electron beam melting (EBM) and wrought Ti–6Al–4V using small punch test

The influence of electrochemical charging of hydrogen at j = ?5 mA/cm² for 6, 12, 48 and 96 h on the structural and the mechanical behavior of wrought and electron beam melting (EBM) Ti–6Al–4V alloys containing 6 wt% β and similar impurities level was investigated. The length of the α/β interphase boundaries in the EBM alloy was larger by 34% compared to that in the wrought alloy. The small punch test (SPT) technique was used to characterize the mechanical behavior of the non-hydrogenated and hydrogenated specimens. It was found that the maximum load and the displacement at maximum load of the wrought alloy remained nearly stable after 6 h of charging, showing a maximum decrease of ～32% and 11%, respectively. Similarly, hydrogenation of the EBM alloy resulted in a gradual degradation in mechanical properties with charging time, up to ～81% and 86% in pop-in load and displacement at the “pop-in” load, respectively. The mode of fracture of the wrought alloy changed from ductile to semi-brittle with mud-cracking in all hydrogenated specimens. In contrast, the mode of fracture of the EBM alloy changed from a mixed mode ductile-brittle fracture to brittle fracture with star-like morphology. The degraded mechanical properties of the EBM alloy are attributed to its α/β lamellar microstructure which acted as a short-circuit path and enhanced hydrogen diffusion into the bulk as well as δ_a and δ_b hydride formation on the surface. In contrast, a surface layer with higher concentration of δ_a and δ_b hydrides in the wrought alloy served as a barrier to hydrogen uptake into the bulk and increased the alloy resistivity to hydrogen embrittlement (HE). This study shows that EBM Ti–6Al–4V alloy is more susceptible to mechanical degradation due to HE than wrought Ti–6Al–4V alloy.     

Preparation of highly crystalline titanium-based ceramic microfibers from polymer precursor blend by needle-less electrospinning

The aim of the present contribution is to study the influence of the post-spinning heat - treatment of single TiO₂/PVP precursor fibers on the properties and morphology of the final titanium-based microfibers. The post-spinning treatment conditions were: calcination in air at 450–600?°C and pyrolysis in argon at 1000–1700?°C. Calcination resulted in a production of anatase-rich and pure rutile fibers. The use of an alternative sintering method, the low-temperature plasma treatment, led to the crystallization of the composite Magnéli phases/polymer fibers. As a result of the same one precursor, pyrolysis at 1000?°C, the Carbon/TiO₂ composite fibers were obtained. Rising the treatment temperature in inert atmosphere led to the formation of the titanium carbide fibers. The formation process and all the obtained products were characterized by differential scanning calorimetry accompanied with thermogravimetric analysis (DSC/TGA), scanning and transmission electron microscopy (SEM, TEM), X-ray diffraction (XRD), and image analysis techniques.     

油气开采用钛合金石油管材料耐腐蚀性能研究

选取5种油气开发常用钛合金材料(Ti-6Al-4V、Ti-6Al-4V-0.1Ru、Ti-6Al-2Sn-4Zr-6Mo、Ti-3Al-8V-6Cr-4Zr-4Mo和Ti-5.5Al-4.5V-2Zr-1Mo)为研究对象,使用高温高压釜模拟国内典型严酷服役工况环境,研究了不同钛合金材料耐均匀腐蚀、局部腐蚀、点蚀、应力腐蚀开裂(SCC)及缝隙腐蚀的性能,通过使用扫描电镜和能谱分析等手段对腐蚀形貌和腐蚀产物进行了分析,并使用电化学方法对不同合金的耐腐蚀机理进行了研究。结果显示,在所测试工况条件下,所有钛合金材料腐蚀反应均为阳极控制过程,均匀腐蚀速率均低于0.001mm/a,并且对应力腐蚀开裂均有良好的抗力。Ti-6Al-4V和Ti-5.5Al-4.5V-2Zr-1Mo合金出现明显的点蚀和缝隙腐蚀问题。对腐蚀机理研究表明,在工况条件温度下,随着pH值的降低,所有钛合金均发生自腐蚀电位降低,极化电阻减小,腐蚀电流增大,耐腐蚀性能下降,其中Ti-6Al-4V耐腐蚀性能下降的最为明显,研究结果为油气开发工况下钛合金石油管的选材和缝隙腐蚀问题防治提供理论基础。     

Industrial TiO2 based nacreous pigments as functional building materials: Photocatalytic removal of NO

In this paper, the photocatalytic activity of industrial titanium dioxide (TiO₂) based nacreous pigments was researched as functional building materials for photocatalytic NO remove. Three industrial TiO₂ based nacreous pigments were selected to estimate the photocatalytic activity for NO remove. This study is a good proof that pearlescent pigments can eliminate NO, and its performance is positively correlated with its titanium dioxide content. And this research will widen the application of nacreous pigments in functional building materials, and provide a new way to eliminate in door nitric oxide pollution.     

船舶海水管路钛合金应用技术研究

钛合金以其高比强度、优良的耐海水腐蚀性能,成为未来船舶选材的热点。综述了海水管路用钛合金的材料选用、焊接技术、弯管技术、腐蚀防护以及防海生物污损等方面的研究工作进展并进行分析,证明钛合金是船舶海水管路系统的理想选择,以期推动钛合金在船舶海水管路的推广和应用。     

Electrospinning preparation and dye adsorption capacity of TiO2@Carbon flexible fiber

TiO₂@carbon flexible fiber was prepared by combining electrostatic spinning technology and hydrothermal synthesis method. The XRD, SEM, TEM and Zeta potential techniques were used to characterize the phase, microstructure and surface charge properties of the samples. The growth mechanism of TiO₂ nanoarray on carbon flexible fiber with different morphologies was studied, and the dye adsorption capacity of the samples was evaluated by methylene blue (MB) degradation effect. The results showed that proper doping amounts of TiO₂ particles improved the flexibility and the hydrophilic property of carbon fiber significantly, which was conducive to the deposition and growth of TiO₂ on the carbon fiber. With the increase of hydrothermal time, the TiO₂ nanoarray grew denser gradually along the [110] crystal surface. The negative charge on the surface of carbon fiber increased, which was benefited to the removal of MB. The dye adsorption capacity of TiO₂@carbon fiber was resulted from the synergistic effect of physical adsorption (carbon fiber) and photocatalysis (TiO₂) process.     

Aerosol synthesis of titanium nitride nanoparticles by direct current arc discharge method

Arc discharge synthesis has industrial relevance due to its low cost and scale-up potential. The production of titanium nitride nanoparticles was achieved by direct current arc discharge in an atmospheric-pressured ambient composed of N₂ and Ar. We systematically investigated the effect of the synthesis parameters, including quench gas velocity, quench gas composition, and applied arc current, on the particle quality, yield, and size. It is found that increasing quench gas velocity enables to produce particles with a primary size of 10–15 nm, while titanium nitride particles of 20–50 nm are produced at low quench gas velocity based on scanning electron microscope (SEM) analysis. X-ray diffraction (XRD) results indicated that titanium nitride particles produced at various nitrogen compositions are almost stoichiometric, while the crystallite size increases almost 20 nm when increasing nitrogen contents in the quench gas. Quench gas composition also has a significant impact on the arc voltage as well as particle production rate. When increasing the nitrogen concentration from 20% to 100%, the production rate can be enhanced by a factor of three. Besides, raising the applied arc current from 12 A to 50 A leads to a yield enhancement of factor 10. According to the Brunauer-Emmett-Teller (BET) measurement, the increase of applied arc current has a limited impact on primary particle size. The enhancement in particle production rate is mainly reflected by the larger agglomerate sizes and agglomerate number concentration. Additionally, based on experimental observations and previous studies, a mechanism is presented to explain the growth of deposits on the cathode tip.     

Electrolytic synthesis of TiC/SiC nanocomposites from high titanium slag in molten salt

The molten salt electrolytic method for the preparation of titanium carbide and silicon carbide composites has been subjected to a systematic investigation by experimental analyses and thermodynamic calculations. It has been confirmed that the electrolysis of high titanium slag in the presence of mixed graphite powders generates intermediates CaTiO₃, Ti₂O₃, TiO, Fe₃Si and objective carbonous products TiC/SiC. It has been furthermore found that the deoxidization process depends critically on a number of process parameters, namely, electrolyte composition, graphitic regime, reaction temperature, cell voltage and reaction time. After careful optimization of these parameters, TiC/SiC nanocomposites with particle sizes of 10–174 nm has been produced by electrolysis of high titanium slag and graphite mixtures in molar ratio of 1:2 referred to Ti:C under 3.2 V at 900 °C for 6 h in 1 mol%CaO-CaCl₂-NaCl molten salt and with particle sizes of 12 nm~207 nm in 1 mol%CaO-CaCl₂ electrolyte.     

Fabrication of Ti3SiC2-based pastes for screen printing on paper-derived Al2O3 substrates

This paper describes the development and fabrication of pastes suitable for screen printing process using Ti₃SiC₂ as the ceramic filler and ethyl cellulose as the binder. With the aim of obtaining high quality screen printed films, the influence of different amounts of Ti₃SiC₂ filler (20–40?vol%) and binder (0–5?vol%) on the rheological properties of the pastes was investigated. Samples with higher viscosity, such as pastes containing 30?vol% and 40?vol% Ti₃SiC₂ filler, regardless of the amount of ethyl cellulose, showed a higher printing quality compared to the samples with other compositions. The different paste compositions were screen printed onto paper-derived Al₂O₃ substrates containing 28.6 ± 4.8% open porosity and sintered for 1?h under an argon atmosphere at 1600?°C. X-ray diffraction (XRD) measurements and scanning electron microscopy (SEM) analysis showed that the sintered films contained TiC as a primary phase and Ti₃SiC₂ as a secondary phase. The partial decomposition of Ti₃SiC₂ after sintering can be attributed to residual carbon from the organic additives, which decreases the thermal stability of this material.     

Effect of C/Ti ratio on densification,microstructure and mechanical properties of TiCx prepared by reactive spark plasma sintering

Titanium carbide (TiC) has been widely used as reinforcement in metal matrix composites and is known to exist over a wide range of stoichiometry. In this study, the effect of C/Ti ratio on the densification kinetics, grain size, lattice parameter, hardness and elastic modulus of TiC_x prepared by reactive spark plasma sintering (RSPS) is presented. Commercial purity titanium was ball milled with 5, 7.5, 10, 12.5, 15 and 17.5 wt% carbon black powder for 5 h and subjected to RSPS to prepare TiC_x samples with different C/Ti ratio. Dense TiC_x samples with ‘x′ ranging from 0.34 to 0.78 could be prepared by RSPS at 1400 °C. Increasing C/Ti ratio was found to increase the activation energy thereby reducing the rate of sintering and also resulted in finer grain size. The lattice parameter and the ratio of intensities of (200) to (111) peaks were correlated with the C/Ti ratio. The hardness and elastic modulus were shown to increase significantly with increase in C/Ti ratio.