上保护层开采底板破坏深度和应力分析研究

上保护层开采导致的底板变形、应力释放会使被保护层内高瓦斯沿着上覆岩层内形成的空隙裂隙结构向上运移，很容易造成所采工作面采空区内瓦斯增加，造成工作面瓦斯超限。以峰峰集团以黄沙矿为研究实例，针对其主采的2号煤层利用FLAC^3D模拟软件进行上保护层开采底板应力研究，揭示了上保护层开采底板应力的规律特性，对于保护层开采工作瓦斯治理具有一定的指导意义。     

槽式太阳能集热管内相变微胶囊悬浮液的热力性能分析

针对传统使用水基和油基的太阳能集热器换热效果低和管壁热应力大的问题，以相变微胶囊悬浮液为工作流体，对抛物型槽式太阳能集热器进行了三维建模。采用蒙特卡罗射线追踪法结合有限容积法和有限元法的方法求解了太阳能集热管的光?热?力耦合问题，采用欧拉?欧拉多相流模型研究了相变微胶囊悬浮液在集热管内的流动换热特性。结果表明，相变微胶囊悬浮液强化了集热管内的对流换热，不仅降低了集热管的沿程壁温，且减少了集热管的周向温差，均化了集热管温度分布。集热管周向等效热应力呈花瓣型分布，对应的5个高温度梯度的位置附近(圆周角θ=5°, 90°, 175°, 225°和315°)出现等效应力局部峰值。吸热管内壁面θ=90°处轴向热应力为压应力，作用于整个管程，而径向热应力和切向热应力为拉应力，主要作用在进出口端。相变微胶囊悬浮液浓度越高，强化换热效果越好，集热管热应力越小，但产生的压降也随之增大。     

Genes Identification,Molecular Docking and Dynamics Simulation Analysis of Laccases from Amylostereum areolatum Provides Molecular Basis of Laccase Bound to Lignin

An obligate mutualistic relationship exists between the fungus Amylostereum areolatum and woodwasp Sirex noctilio. The fungus digests lignin in the host pine, providing essential nutrients for the growing woodwasp larvae. However, the functional properties of this symbiosis are poorly described. In this study, we identified, cloned, and characterized 14 laccase genes from A. areolatum. These genes encoded proteins of 508 to 529 amino acids and contained three typical copper-oxidase domains, necessary to confer laccase activity. Besides, we performed molecular docking and dynamics simulation of the laccase proteins in complex with lignin compounds (monomers, dimers, trimers, and tetramers). AaLac2, AaLac3, AaLac6, AaLac8, and AaLac10 were found that had low binding energies with all lignin model compounds tested and three of them could maintain stability when binding to these compounds. Among these complexes, amino acid residues ALA, GLN, LEU, PHE, PRO, and SER were commonly present. Our study reveals the molecular basis of A. areolatum laccases interacting with lignin, which is essential for understanding how the fungus provides nutrients to S. noctilio. These findings might also provide guidance for the control of S. noctilio by informing the design of enzyme mutants that could reduce the efficiency of lignin degradation.     

退火温度对0Cr25Al5热轧态盘条钢组织及性能的影响

采用显微组织分析和分子动力学模拟等方法研究了退火温度对0Cr25Al5热轧态盘条钢组织及性能的影响。结果发现,晶粒尺寸随温度的升高逐渐增加并趋于稳定,但是断后伸长率和断面收缩率在950 ℃突然大幅度下降。试样组织形貌在800 ℃和950 ℃退火温度下的OM及SEM分析结果未见明显差别。于是使用分子动力学模拟对0Cr25Al5钢三元体系的自由能进行了计算,发现随着B2结构的FeAl或者DO3结构的Fe₃Al有序相尺寸的增大,系统自由能先减小后增大,其最小值随着退火温度的升高向有序相颗粒尺寸减小的方向移动。在1273 K的高温下仍然会保留60 nm左右大小的有序相颗粒。因此,推测0Cr25Al5钢在大于950 ℃的温度范围内韧性下降是由于60 nm左右的B2结构的FeAl或者DO3结构的Fe₃Al有序相造成,与晶粒尺寸无关。因此,针对该钢种应进行低温退火促使基体组织回复以消除缺陷,从而抑制Fe、Al等基体原子的扩散。     

小型特种精细化工过程自动化和信息化研究发展趋势探讨

针对采取小批量间歇性批次生产方式、工艺介质腐蚀性强、危险性大的小型特种精细化工生产工艺研究试验过程自动化、信息化程度不高，导致工艺研究试验中获取数据较少、过程机理研究不够透彻、人工操作多、安全风险高、研究试验消耗大及效率不高等问题，综述了期待通过智能控制、在线分析、模拟仿真和虚拟制造、工况监测及预测性维护以及信息管理和生产调度等关键技术的研究和应用，提高小型特种精细化工生产工艺过程的自动化和信息化程度，实现小型特种精细化工生产工艺过程的数字化、虚拟化和智能化，降低生产安全风险和试验消耗，提高小型特种精细化工生产工艺研究试验的成功率和效率，达到小型特种精细化工生产工艺过程的数字化设计和精准生产的目标。     

装填设备载荷影响因素分析及动力学仿真

大型货物的装填过程中影响载荷的因素较多,其中对中精度对装填载荷影响较为明显。通过动力学仿真软件ADAMS对装填过程中载荷进行模拟,并对各影响因素进行定量分析,得到对中偏差与装填载荷的关系。将仿真结果与试验数据进行对比,验证该仿真方法的正确性,可作为后续研究装填载荷的一种方法,为结构设计提供指导。     

CFD modeling of thermal contact resistance between solid contacting surfaces

Heat transfer has considerable applications in different industries such as designing of heat exchanger, nuclear reactor cooling, control system for spacecraft, and designing of microelectronics cooling. As the surfaces of two metals contact each other, this issue becomes so crucial. Thermal contact resistance (TCR) is one of the key physical parameters in heat transfer of mentioned surfaces. Measuring the experimental value of TCR in laboratory is highly expensive and difficult. As an alternative, numerical modeling methods could be engaged. In this study, inverse problem method solution is utilized as a proper method for estimation of TCR value. In this order, three different configurations (flat-flat, flat-cylinder, and cylinder-cylinder) were utilized in two steady and unsteady state conditions to predict the value of TCR. A comparison between the measured values and obtained values from the simulation show the errors for flat-flat, flat-cylinder, and cylinder-cylinder configuration after 10 min from starting the experiment are 4.6074%, 0.1662%, and 0.5622%, respectively. And in steady-state condition, the corresponding errors are 6.06e-3%, 1.506%, and 0.846%, respectively. In conclusion, the final results establish the fact that the inverse problem method solution can predict TCR values between contacting surfaces.     

改性淀粉抑制赤铁矿反浮选石英的作用机理研究

通过矿物浮选试验、动电位测定以及吸附量测试,考察了4种淀粉抑制剂对赤铁矿和石英浮选性能的影响,并探讨了其作用机理。在碱性条件下,改性淀粉抑制剂对赤铁矿抑制效果明显,且以改性玉米淀粉效果最佳,改性磷酸酯淀粉、改性羧甲基淀粉的抑制效果次之,而普通淀粉抑制作用一般。同时4种淀粉抑制剂对主要脉石矿物石英的抑制效果均不明显。pH=10~12.5条件下,改性玉米淀粉因其羟基氧和裸露在赤铁矿表面的铁元素发生了化学键合,因而选择性抑制能力最佳。分子动力学模拟表明,改性玉米淀粉片段与赤铁矿作用更为紧密,验证了改性淀粉能更好地抑制赤铁矿。     

Outcome‐based ventilation: A framework for assessing performance,health, and energy impacts to inform office building ventilation decisions

This article presents an outcome‐based ventilation (OBV) framework, which combines competing ventilation impacts into a monetized loss function ($/occ/h) used to inform ventilation rate decisions. The OBV framework, developed for U.S. offices, considers six outcomes of increasing ventilation: profitable outcomes realized from improvements in occupant work performance and sick leave absenteeism; health outcomes from occupant exposure to outdoor fine particles and ozone; and energy outcomes from electricity and natural gas usage. We used the literature to set low, medium, and high reference values for OBV loss function parameters, and evaluated the framework and outcome‐based ventilation rates using a simulated U.S. office stock dataset and a case study in New York City. With parameters for all outcomes set at medium values derived from literature‐based central estimates, higher ventilation rates’ profitable benefits dominated negative health and energy impacts, and the OBV framework suggested ventilation should be ≥45 L/s/occ, much higher than the baseline ~8.5 L/s/occ rate prescribed by ASHRAE 62.1. Only when combining very low parameter estimates for profitable impacts with very high ones for health and energy impacts were all outcomes on the same order. Even then, however, outcome‐based ventilation rates were often twice the baseline rate or more.     

浮法玻璃熔窑火焰空间石油焦部分替代重油燃烧的数值模拟

针对浮法玻璃熔窑火焰空间建立模型并进行了数值模拟，在保证热值相同的前提下，对比研究了重油燃烧及将石油焦部分替代重油燃烧时的流场分布特征。结果表明，石油焦部分代替重油燃烧后，两种燃料可很好地混合燃烧，窑炉内温度制度基本不受影响；石油焦着火时间比重油长，两种燃料混合燃烧时平均着火点滞后于仅使用重油时，且燃烧路径更长，燃烧时产生了大量CO，整个火焰空间及烟气出口处NOx的平均排放量与仅使用重油相比降低了30.02%，NOx减排效果明显。