基于多特定决策类的不完备决策系统正域约简

现有的属性约简方法大部分关注决策系统中的所有决策类，而在实际决策过程中决策者往往仅关注决策系统中的一种或几种决策类。针对上述问题，提出基于多特定决策类的不完备决策系统正域约简的理论框架。首先，给出不完备决策系统单特定决策类正域约简的概念；第二，将单特定决策类正域约简推广到多特定决策类，构造了相应的差别矩阵及区分函数；第三，分析并证明了相关定理，提出基于差别矩阵的不完备决策系统多特定决策类正域约简算法（PRMDM）；最后，选取4组UCI数据集进行实验。在数据集Teaching-assistant-evaluation、House、Connectionist-bench和Cardiotocography上，基于差别矩阵的不完备决策系正域约简算法（PRDM）的平均约简长度分别为4.00、13.00、9.00和20.00，PRMDM算法（多特定决策类中决策类数目为2）的平均约简长度分别为3.00、8.00、8.00和18.00。实验结果验证了PRMDM算法的有效性。     

High strain rate compressive response of the Cf/SiC composite

Carbon fiber reinforced ceramic owns the properties of lightweight, high fracture toughness, excellent shock resistance, and thus overcomes ceramic's brittleness. The researches on the advanced structure of astronautics, marine have exclusively evaluated the quasi-static mechanical response of carbon fiber reinforced ceramics, while few investigations are available in the open literature regarding elastodynamics. This paper reports the dynamic compressive responses of a carbon fiber reinforced silicon carbide (C_f/SiC) composite (CFCMC) tested by the material test system 801 machine (MTS) and the split Hopkinson pressure bar (SHPB). These tests were to determine the rate dependent compression response and high strain rate failure mechanism of the C_f/SiC composite in in-plane and out-plane directions. The in-plane compressive strain rates are from 0.001 to 2200?s^?1, and that of the out-plane direction are from 0.001 to 2400?s^?1. The compressive stress-strain curves show the C_f/SiC composite has a property of strain rate sensitivity in both directions while under high strain rate loadings. Its compressive stiffness, compressive stress, and corresponding strain are also strain rate sensitive. The compressive damage morphologies after high strain rate impacting show different failure modes for each loading direction. This study provides knowledge about elastodynamics of fiber-reinforced ceramics and extends their design criterion with a reliable evaluation while applying in the scenario of loading high strain rate.     

基体稀释或基体匹配石墨炉原子吸收光谱法测定土壤样品中铅和镉

用石墨炉原子吸收光谱法测定土壤样品中Pb和Cd时,有时候直接按照方法标准GB/T 17141—1997操作,测定结果不能满足质控要求。研究结果表明,目标元素系列标准溶液中,分别含和不含土壤基体元素Na、Mg、Al、Si、Fe、Ca等元素混合成分时,校准曲线斜率明显不同。为减小基体效应的影响,基于文献调研和实验结果,对上述方法标准实验步骤进行了下列改进:(1)取相同体积实际样品消解液混合后,定量加入到用于建立校准曲线的系列标准溶液中,用于基体匹配;(2)对消解液进行适度稀释,仍采用标准溶液建立校准曲线。用4个土壤标样和土壤样品加标测定结果对改进后的方法进行了验证,结果表明,基体稀释法测定Pb的回收率范围分别为90.4%~114%;测定低含量Cd时,回收率范围为84.1%~125%。基体匹配法测定Pb和Cd的回收率范围分别为93.0%~105%和102%~119%,基本满足土壤样品中重金属回收率为80%~120%的质控要求。样品中痕量镉在测定下限附近时,应严格控制稀释倍数,或采用基体匹配法测定。改进后的操作步骤适合日常检测工作中大批量土壤样品中Pb和Cd的准确测定。     

工业硝酸铵添加剂对乳胶基质的影响

为了改善工业硝酸铵的吸湿结块性能,通常会加入添加剂(有机包覆剂或无机改性剂),而工业硝酸铵作为乳化炸药的主要原料,其添加剂对乳化炸药的制备和性能会产生影响。因此,分别对采用有机包覆剂蜡的泰国产工业硝酸铵和采用无机改性剂的俄罗斯产工业硝酸铵,开展了制备现场散装乳胶基质的工业试验。结果表明:两类工业硝酸铵均可作为乳化炸药原材料使用,但有机包覆剂会沉入水相罐底部或粘附在输送管道内壁,对水相和乳胶基质制备造成不利影响,因此需要在水相制备环节分离去除包覆剂蜡;硝酸镁、硝酸钙等无机改性剂对乳胶基质制备无影响,但生产的乳胶基质稳定性较差,通过调整乳化剂的种类和配比以及乳化器的转速可得到一定改进。     

一种基于压缩感知的运动目标检测技术

运动目标检测是计算机视觉、图像处理等相关领域的研究热点，其核心就是对视频图像中的每一帧图像进行相应的研究和处理。本文主要研究思路是从压缩感知技术采样信号的角度出发，将每一帧的二维图像压缩采样成具有少量信息的一维信号，再通过信号重构用少量数据量将图像重构出来，最后通过目标检测技术对每一帧的图像进行运动目标提取。仿真实验表明该方法是可行和有效的，同时可以大大减少目标检测中所记录的数据量，解决海量数据的存储与传输问题。     

基于计算机的镀液温度智能控制系统设计

为提高镀液温度的控制精度,以计算机为平台设计了一种镀液温度智能控制系统。设计了一种模糊PID温度控制器,可实现PID控制器参数的实时在线调整。利用动态矩阵,统计过去和当前时刻的偏差,预测未来偏差,进而得到最佳输入。最后,进行了实验研究。结果表明:镀液温度智能控制系统的收敛速率快、精度高、稳定性好,能满足电镀行业的需求,具有广阔的应用前景。     

Switching controller design for linear time invariant plant with a single I/O delay

ABSTRACT

To deal with the problem of conflicting requirements that cannot be satisfied by only a single LTI controller, this paper focuses on the design of a switching controller, which includes several stabilising linear time-invariant (LTI) controllers designed independently with different control performance criteria, for a specific LTI plant with a single I/O delay. The switching controller design procedure is divided into three steps. First, using simple loop shifting arguments, the design problem is reducible to an equivalent delay-free one. Second, traditional LTI controller synthesis methods could be considered independently for the delay-free plant. Third, based on a quadratically stable state space realisation method, a Youla parameter including a switching strategy with these controllers is designed to guarantee different requirements. Finally, a numerical example is provided to demonstrate the validity and efficiency of the approach.     

Effects of SiC content on the densification,microstructure, and mechanical properties of HfB2–SiC composites

To investigate the effects of SiC on microstructure, hardness, and fracture toughness, 0, 10, 20, and 30 vol% SiC were added to HfB₂ and sintered by SPS. Upon adding SiC to 30 vol%, relative density increased about 4%; but HfB₂ grain growth had a minimum at 20 vol% SiC. This may be due to grain boundary silicate glass, responsible for surface oxide wash out, enriched in SiO₂ with higher fraction of SiC. By SiO₂ enrichment, the glass viscosity increased and higher HfO₂ remained unsolved which subsequently lead to higher grain growth. Hardness has increased from about 13 to 15 GPa by SiC introduction with no sensible variation with SiC increase. Residual stress measurements by Rietveld method indicated high levels of tensile residual stresses in the HfB₂ Matrix. Despite the peak residual stress value at 20 vol% SiC, fracture toughness of this sample was the highest (6.43 MPa m^0.5) which implied that fracture toughness is mainly a grain size function. Tracking crack trajectory showed a mainly trans-granular fracture, but grain boundaries imposed a partial deflection on the crack pathway. SiC had a higher percentage in fracture surface images than the cross-section which implied a weak crack deflection.     

C/C-SiC component for metallic phase change materials

Thanks to their high energy density and thermal conductivity, metallic Phase Change Materials (mPCM) have shown great potential to improve the performance of thermal energy storage systems. However, the commercial application of mPCM is still limited due to their corrosion behavior with conventional container materials. This work first addresses on a fundamental level, whether carbon-based composite-ceramics are suitable for corrosion critical components in a thermal storage system. The compatibility between the mPCM AlSi₁₂ and the Liquid Silicon Infiltration (LSI)-based carbon fiber reinforced silicon carbide (C/C-SiC) composite is then investigated via contact angle measurements, microstructure analysis, and mechanical testing after exposure. The results reveal that the C/C-SiC composite maintains its mechanical properties and microstructure after exposure in the strongly corrosive mPCM. Based on these results, efforts were made to design and manufacture a container out of C/C-SiC for the housing of mPCM in vehicle application. The stability of the component filled with mPCM was proven nondestructively via computer tomography (CT). Successful thermal input- and output as well as thermal storage ability were demonstrated using a system calorimeter under conditions similar to the application. The investigated C/C-SiC composite has significant application potential as a structural material for thermal energy storage systems with mPCM.     

基于ELM的英语教学质量评价研究

对英语教学质量实施科学化的评价关系到英语教学质量的提升,为减少主观因素的影响,本文提出一种ELM的教学质量评价方法,该种方法将可以在很大程度上提高教学质量评价的精度。对影响英语教学质量的12个指标进行打分,以此作为ELM的输入,同时将英语教学质量的综合得分作为ELM的输出。评价结果表明,基于EIM的英语教学质量评价结果比SVM、BP具有了很大程度的提升,为实施英语教学质量的评价提供了参考。