A numerical model to predict the powder–binder separation during micro-powder injection molding

The micro-powder injection molding (micro-PIM) process has the potential to bridge the gap between the design and manufacturing of micro-components that are often used in small and handy devices. Numerical modeling helps to analyze and overcome various difficulties of micro-PIM. In the present work, a numerical model is developed to predict the powder–binder separation (a common defect in PIM and especially severe in micro-PIM) during the injection of an alumina feedstock. A powder–binder separation criterion is proposed dealing with applied injection pressure and friction force between the powder and binder. An indirect comparison of feedstock travel time between two locations is used to validate the model. The predicted segregation from the simulated result is supported by a qualitative experimental measurement. The developed model can be used to optimize injection parameters to get a defect-free product.     

Mg gas infiltration for the fabrication of MgB2 pellets using nanosized and microsized B powders

MgB₂ superconductor pellets were synthesized through Mg gas infiltration method using nanosized- and microsized B powders. There was a marked difference in the superconducting properties of the two samples, particularly in the pinning force and dominant pinning mechanism. The microstructures of the samples were observed using HR-TEM and STEM-HAADF, and the results showed that the primary reason for the difference in the superconducting properties is the distribution of the nanosized second-phase particle MgO. Additionally, a feasible reaction model for the Mg gas infiltration method was established. Compared to the Mg liquid infiltration method, the gas infiltration showed better penetrability ability with a small amount of residual Mg. This study presents a novel synthesis process to fabricate an MgB₂ pellet with superior density and superconducting properties. This method can be used in multiple applications such as superconducting bearings, compact superconductor magnets, and magnetic shielding.     

红心火龙果发酵液喷雾干燥工艺优化及红心火龙果籽油的研究

以红心火龙果发酵液作为研究对象,通过优化喷雾干燥工艺制备粉剂,最佳工艺条件为:20%麦芽糊精,进液量:10mL/min,进口温度为120℃,出口温度为65℃;得到的粉剂为紫红色粉末,益生菌含量达到108cfu/g以上,口感酸甜。将发酵后的火龙果籽进行提取,得到的火龙果籽油含有丰富的十六酸、亚油酸和油酸。     

A numerical study of dynamic behaviors of a unitized regenerative fuel cell during gas purging

The gas purging states affect electricity output and energy storage capacity of unitized regenerative fuel cells. In this study, a model of unitized regenerative fuel cell is established. Cell voltages and operating temperatures influences on the dynamic distribution of thermal fluid during purging process and the discharge of residual liquid water in electrolytic cell mode are investigated. The motivation of the present study is better understanding the gas purging characteristics and its effect on reaction behaviors of unitized regenerative fuel cells. Simulation results reveal a significant influence of purging gas temperature on the water flooding and a great effect of operating voltage on the water diffusion. The operating temperature of electrolytic cell model almost has little effect on purging results at different cell temperature and the same purging gas temperature. When the purging gas temperature is changed, higher temperatures of cell and purging gas facilitate liquid water discharging out from the cell regions. In cell water flooding situation, when having large liquid content, the purging gas has little effects on the water expelling process.     

Predictive process mapping for laser powder bed fusion: A review of existing analytical solutions

One of the main challenges in the laser powder bed fusion (LPBF) process is making dense and defect-free components. These porosity defects are dependent upon the melt pool geometry and the processing conditions. Power-velocity (PV) processing maps can aid in visualizing the effects of LPBF processing variables and mapping different defect regimes such as lack-of-fusion, under-melting, balling, and keyholing. This work presents an assessment of existing analytical equations and models that provide an estimate of the melt pool geometry as a function of material properties. The melt pool equations are then combined with defect criteria to provide a quick approximation of the PV processing maps for a variety of materials. Finally, the predictions of these processing maps are compared with experimental data from the literature. The predictive processing maps can be computed quickly and can be coupled with dimensionless numbers and high-throughput (HT) experiments for validation. The present work provides a boundary framework for designing the optimal processing parameters for new metals and alloys based on existing analytical solutions.     

Effect of coral sand powders and seawater salinity on the impact mechanical properties of cemented coral sand

Coral sand is one kind of the important building materials in coral reef engineering practice. The use of cement as a stabilizing agent can significantly improve the mechanical properties of coral sands and is widely applied in the subbase engineering construction in coral reef islands. Cement-stabilized coral sand structures may contain high contents of fine coral particles and salinity because of the high crushability of coral sands and the existence of seawater surrounding them. In this study, the effects of coral sand powders and seawater salinity on the dynamic mechanical properties of cemented coral sand (CCS) were investigated through the split Hopkinson pressure bar (SHPB) tests and Scanning Electron Microscope (SEM) analysis. It was found that the strength (i.e., the peak stress) of CCS specimens increased firstly and then decreased with the increase of powder content. The specimens reached the maximum peak stress when 3% powder content was included. The initial improvement of CCS strength was attributed to the pore-filling effect of coral powders, namely, the micro pores of the CCS specimens could be more effectively filled with higher percentages of coral powders being used in the experiments. However, excessive coral powders resulted in the reduction of specimen strength because these powders could easily be cemented into agglomerates by absorbing water from the specimens. These agglomerates could reduce the cementation strength between the coarse coral particles and the cement. Meanwhile, the peak stress of CCS specimens was found to be negatively correlated with the average strain rate and the ultimate strain. The degree of specimen fracture was found to be correlated with the amount of specific energy absorption during the tests. Furthermore, the “sulfate attack” caused by the inclusion of salinity of water had different influences on the CCS specimens with different coral powder contents. The ettringite and gypsum produced in “sulfate attack” could fill the pores and lead to cracking of the specimens, significantly affecting the specimen strength.     

The kinetics of copper corrosion in nitric acid

The strategy for the permanent disposal of high-level nuclear waste in Canada involves sealing it in a copper-coated steel container and burying it in a deep geologic repository. During the early emplacement period, the container could be exposed to warm humid air, which could result in the condensation of nitric acid, produced by the radiolysis of the humid air, on the copper surface. Previous studies have suggested that both nitrate and oxygen reduction will drive copper corrosion, with the nitrate reduction kinetics being dependent on the concentration of soluble copper(I) produced by the anodic dissolution of copper in the reaction with oxygen. This study focused on determining the kinetics of nitrate and oxygen reduction and elucidating the synergistic relationship between the two processes. This was investigated using corrosion potential and polarization measurements in conjunction with scanning electron microscopy and X-ray photoelectron spectroscopy. Oxygen reduction was shown to be the dominant cathodic reaction with the oxidation of copper(I) to copper(II) by nitrate, promoting the catalytic cycle involving the reaction of copper(II) with copper to reproduce copper(I).     

磁性硅铁载铜吸附Hg0动力学机制及密度泛函研究

采用粉末冶金法将纳米单质铜(Cu⁰)、硅铁(FeSi)、四氧化三铁硅涂层(Fe₃O₄@SiO₂)混合煅烧并制备出新型磁性硅铁载铜吸附剂MagFeSi-Cu⁰。实验研究不同烟气温度下MagFeSi-Cu⁰的汞吸附能力基础上,结合颗粒内扩散模型、准二阶动力学模型、Elovich模型及Bangham模型分析了MagFeSi-Cu⁰吸附Hg⁰过程的主要控制步骤。在此基础上,依据密度泛函理论(DFT)研究了不同反应温度下FeSi表面Cu⁰原子与Hg⁰原子的汞齐作用机制。研究结果表明,Bangham模型的拟合值与MagFeSi-Cu⁰汞吸附实验值拟合度最高,MagFeSi-Cu⁰表面痕量Hg⁰吸附由汞的外扩散和表面铜汞齐吸附共同控制;通过密度泛函计算,发现Cu⁰颗粒表面Cu-Hg齐吸附能为-0.534 eV,当烟气温度从80℃上升至200℃时,Hg⁰原子与单质Cu原子的吸附自由能从-22.47 kJ/mol下降至-13.96 kJ/mol,这些结果为深入了解Hg⁰在Cu(111)表面的反应机理提供了理论基础。     

Effect of ball-milling parameters on the rheological properties of mold powder slurry

In this study, mold powder slurries with high solid loading and low viscosity were prepared during the ball-milling process for improving the homogeneity and mechanical properties of granules after spray-drying. The effect of ball-milling parameters, such as solid loading, binder/dispersant content, and ball-milling time, on the flowability, dispersibility, stability, and rheological behavior of mold powder slurries was systematically investigated by rheology observation and sedimentation tests. As these parameters varied, the slurry exhibited the shear-thinning behavior of a non-Newtonian fluid with a shear rate range of 0–50 s^?1, which was adequately described by the Herschel-Bulkley model. The optimal parameters that optimized the flowability, dispersibility, and stability of the slurry, along with its rheological behavior, were chosen as follows: solid loading, 60 wt%; modified sodium carboxymethyl cellulose binder content, 1.0 wt%; sodium tripolyphosphate dispersant content, 0.5 wt%; ball-milling time, 60 min.