复杂环境下氧化铝储槽定向爆破拆除

在较为复杂的环境下,爆破拆除钢筋混凝土氧化铝储槽。该储槽自重大、呈圆形,内有4根立柱支撑下料漏斗。为使储槽顺利定向倒塌,通过爆破方案选择、参数确定,采取梯形切口和预处理以及安全防护和减振措施,使储槽爆破拆除获圆满成功。     

基于数值模拟的挤压参数对AZ91镁合金管转角焊合室分流挤压焊合压力的影响规律研究

提出了一种镁合金管材转角焊合室分流挤压新工艺，该工艺可在有效延长焊合室长度和焊合时间前提下保证舌针刚度，从而保证管材尺寸精度，并且可通过转角剪切变形机制增加预焊合金属变形量和动态再结晶程度，从而有利于提高管材性能和焊缝焊合性能。利用有限元法揭示了转角焊合室分流挤压成形过程中金属的流动特征，应变分布特征和焊合室内的静水压力分布特征。结果表明，整个挤压过程无金属折叠，从而保证管材的表面质量；流经转角后预焊合金属变形量明显增加，有利于提高管材质量和焊缝质量。最后，研究揭示了坯料初始温度，挤压速度和模具转角对焊合室内静水压力的影响规律。结果表明，随着挤压速度的增加和模具转角的增大，转角焊合室内静水压力增大；随着坯料预热温度的增加，转角焊合室内静水压力呈先增大后减小的趋势。     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

Flash joining of alumina ceramics under a small current density

The ceramic joining using electric field (E-field) has garnered significant research attention due to the decreased joining barrier and enhanced reliability. However, the underlying mechanism of E-field assisted joining remains unclear. Herein, we report the rapid joining of alumina ceramics using a small current. Moreover, the E-field is applied in both perpendicular and parallel directions to the faying surfaces, demonstrating a significant difference in terms of joint strength. These results indicate that the E-field generates defects and promotes the joining process by facilitating ionic diffusion.     

Droplet Entrainment Analysis in a Flash Evaporator with an Image-Based Measurement Technique

Local droplet sizes and volumes of entrained liquid are captured with an image-based measurement technique for comparison with a conventional, integral method for entrainment analysis. Experiments in a forced circulation flash evaporation were performed for different operating conditions and with two different chemical systems. Droplet size and frequency rise with an increase in thermal energy input. The local readings confirm the trends found by the integral measurement method. The modification of the image-based probe enables the detection of small (≈ 10 µm) and at the same time fast droplets under challenging operating conditions, such as vacuum and superheated feed similar to industrial process conditions.     

A thermal perspective of flash sintering: The effect of AC current ramp rate on microstructure evolution

In flash sintering experiments, the thermal history of the sample is key to understanding the mechanisms underlying densification rate and final properties. By combining robust temperature measurements with current-ramp-rate control, this study examined the effects of the thermal profile on the flash sintering of yttria-stabilized zirconia, with experiments ranging from a few seconds to several hours. The final density was maximized at slower heating rates, although processes slower than a certain threshold led to grain growth. The amount of grain growth observed was comparable to a similar conventional thermal process. The bulk electrical conductivity correlated with the maximum temperature and cooling rate. The only property that exhibited behavior that could not be attributed to solely the thermal profile was the grain boundary conductivity, which was consistently higher than conventional in flash sintered samples. These results suggest that, during flash sintering, athermal electric field effects are relegated to the grain boundary.     

Exploring the influences of the counterpart materials on friction and wear behaviors of atmospheric plasma-sprayed YSZ coating

Sliding wear behaviors of atmospheric plasma-sprayed Yttria Stabilized Zirconia (YSZ) coating mated with four metallic or ceramic counterparts (Si₃N₄, Al₂O₃, GCr15 and ZrO₂) were investigated. It has been found that YSZ coatings in contact with Si₃N₄ and GCr15 show better tribological performances than the other cases, which is due to the formation of the tribolayer mainly consisting of Si₃N₄ and Fe₂O₃ respectively on the worn surfaces. In the case of YSZ coating-Al₂O₃ and YSZ coating-ZrO₂ tribopairs, the wear debris are more irregular and larger in size, resulting in severe abrasive wear and brittle fracture of debris particles. In particular, the specific wear rate of YSZ coating sliding against GCr15 is negative due to the significant material transfer of the tribo-oxide layer, while that of YSZ coating sliding against ZrO₂ is the highest. Amorphization of the wear particles appears in the four cases due to the repeated mechanical action. It has been demonstrated that the wear of YSZ coating deteriorates with the increased flash temperature between the contact surfaces during rubbing process.     

An integrated model for analysing the effects of ultrasonic vibration on tool torque and thermal processes in friction stir welding

An integrated model of ultrasonic vibration enhanced friction stir welding (UVeFSW) is developed by integrating the thermal-fluid model with the ultrasonic field model and tool torque model. The tool torque and the heat generation rate at tool/workpiece contact interfaces are coupled with the interfacial temperature, strain rate and ultrasonic energy density. The model is used in quantitatively analysing the effects of ultrasonic vibration on tool torque and thermal processes in friction stir welding (FSW). The results show that ultrasonic vibration reduces the flow stress, which results in a decreasing of tool torque, interfacial heat generation rate and interfacial temperature. The complicated interaction of ultrasonic energy with the thermal processes in FSW leads to a gentle thermal gradient and an enhanced plastic material flow in UVeFSW. The model is validated by a comparison of the calculated thermal cycles and tool torque at various welding parameters with the experimentally measured ones.     

Measurement of residual stresses in dissimilar friction stir-welded aluminium and copper plates using the contour method

The longitudinal residual stresses in the friction stir-welded plates of 5A06 aluminium and pure copper were determined using the contour method. The results revealed the presence of high tensile and compressive residual stresses on the aluminium and copper sides, respectively. The residual stresses were detected on the weld zone as well as the thermo-mechanically affected zone (TMAZ) of the aluminium plate. In contrast, the compressive residual stresses in the copper plate had a much narrower width along the weld line. Peak tensile stresses up to 240?MPa were found in the TMAZ of the aluminium plate.     

Effect of metallurgical evolution during post-weld aging treatment on localised corrosion of resistance spot welding joints of A286 superalloy

The combined effect of resistance spot welding and precipitation hardening on the localised corrosion of A286 superalloy is studied. The specimens tested by double loop electrochemical potentiokinetic reactivation were welded in the solution treated condition, and then subjected to different precipitation hardening treatments. For both base metal and weld nugget, the maximum localised corrosion is reached when η phase is clearly observable. The fact that the localised corrosion resistance of weld nugget is different from that shown by base metal may be explained by the segregation of Ni and Ti towards the interdendritic region of weld nugget (studied by using scanning electron microscope/energy dispersive X-ray analysis).