Microstructural and mechanical properties assessment of transient liquid phase bonding of CoCuFeMnNi high entropy alloy

The transient liquid phase (TLP) bonding of CoCuFeMnNi high entropy alloy (HEA) was studied. The TLP bonding was performed using AWS BNi-2 interlayer at 1050 °C with the TLP bonding time of 20, 60, 180 and 240 min. The effect of bonding time on the joint microstructure was characterized by SEM and EDS. Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time. For samples bonded at 20, 60 and 180 min, athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn₃Si intermetallic compound. For all samples, the γ solid solution was formed in the isothermal solidification zone of the bonding zone. To evaluate the effect of TLP bonding time on mechanical properties of joints, the shear strength and micro-hardness of joints were measured. The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints. The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min, respectively.     

Spontaneous Directional Self-Cleaning on the Feathers of the Aquatic Bird Anser cygnoides domesticus Induced by a Transient Superhydrophilicity

In nature, the feathers of the goose Anser cygnoides domesticus stay superhydrophobic over a long term, thought as the main reason for keeping the surface clean. However, contaminants, especially those that are oleophilic or trapped within textures, cannot be removed off the superhydrophobic feathers spontaneously. Here, a different self-cleaning strategy based on superhydrophilic feathers is revealed that is imparted by self-coating of the amphiphilic saliva, which enables removing away low-surface-tension and/or small-size contaminants by forming directional water sheeting depending on their unique anisotropic microstructures. Particularly, the surface superhydrophilicity is switchable to superhydrophobicity upon exposure to air for maintaining a clean surface for a long time, which is further enhanced by coating with self-secreted preening oil. By alternate switching between a transient superhydrophilicity and a long-term stable superhydrophobicity, the goose feathers exhibit an integrated smart self-cleaning strategy, which is also shared by other aquatic birds. An attractive point is the re-entrant structure of the feathers, which facilitates not only liquid spreading on superhydrophilic feathers, but also long-term stability of the cleaned surface by shedding water droplets off the superhydrophobicity feathers. Thus, artificial self-cleaning microtextures are developed. The result renews the common knowledge on the self-cleaning of aquatic bird feathers, offering inspiration for developing bioinspired self-cleaning microtextures and coatings.     

Display illumination with modulated directional backlight

Illumination is essential for modern life as colorful world is perceived by human visionary system. Display technology has been developing rapidly in recent decades, and the basic principle is related to the way that the image is illuminated and light is emanated. Traditional illumination is provided by different types of light sources, and the display image is visible in large viewing space until the emanating light decays to zero. This work proposes and demonstrates a novel illumination scheme for a display in which the displaying images are visible only in specific spatial regions. The directional backlight ensures the image propagating to specific direction while imaging visibility can be controlled to terminate abruptly at certain distance from the display screen while exerting no influence to nearby regions. The working principle for such an illumination scheme is the use of the modulated coherent directional backlight through an axicon lens. It is shown that the illumination scheme can robustly deliver carried image information to the designated viewing region. This new illumination scheme has many advantages over conventional illumination, including its usage for personal display, very lower energy consumption, as well as minimizing light hazard pollution.     

Efficiency evaluation of healthcare services in China based on stochastic multicriteria acceptability analysis and directional distance function

Evaluating the efficiency of healthcare services accurately can help in analyzing the rationality of inputs and outputs in such services. Considering the consistency and equity of assessment criteria, this study conducts the stochastic multicriteria acceptability analysis (SMAA-2) with a directional distance function to evaluate the efficiency of healthcare services in 31 provincial administrative regions of mainland China, as observed in 2018. We use SMAA-DDF to explore all the projection directions to the efficient frontier instead of a certain projection direction. We measure the maximum and average efficiencies for each of the 31 provincial healthcare services. Our empirical findings show that only seven provinces achieve optimal healthcare service efficiency; the eastern area performed the best, followed by the central, western, and northeast areas. Furthermore, the path along the projection directions is provided to help inefficient provinces improve their efficiency and obtain the best possible positions.     

New insights into microstructural changes during transient liquid phase bonding of GTD-111 superalloy

The effects of joining temperature (T_J) and time (t_J) on microstructure of the transient liquid phase (TLP) bonding of GTD-111 superalloy were investigated. The bonding process was applied using BNi-3 filler at temperatures of 1080, 1120, and 1160 °C for isothermal solidification time of 195, 135, and 90 min, respectively. Homogenization heat treatment was also applied to all of the joints. The results show that intermetallic and eutectic compounds such as Ni-rich borides, Ni−B−Si ternary compound and eutectic-γ continuously are formed in the joint region during cooling. By increasing t_J, intermetallic phases are firstly reduced and eventually eliminated and isothermal solidification is completed as well. With the increase of the holding time at all of the three bonding temperatures, the thickness of the athermally solidified zone (ASZ) and the volume fraction of precipitates in the bonding area decrease and the width of the diffusion affected zone (DAZ) increases. Similar results are also obtained by increasing T_J from 1080 to 1160 °C at t_J=90 min. Furthermore, increasing the T_J from 1080 to 1160 °C leads to the faster elimination of intermetallic phases from the ASZ. However, these phases are again observed in the joint region at 1180 °C. It is observed that by increasing the bonding temperature, the bonding width and the rate of dissolution of the base metal increase. Based on these results, increasing the homogenization time from 180 to 300 min leads to the elimination of boride precipitates in the DAZ and a high uniformity of the concentration of alloying elements in the joint region and the base metal.     

A Novel Strategy for Preparing Stretchable and Reliable Biphasic Liquid Metal

Low‐melting liquid metal is a hugely promising material for flexible conductive patterns due to its excellent conductivity and supercompliance, especially low‐cost and environmental liquid processing technology. However, the ever‐present fluidity characteristic greatly limits the stable shape and reliability of prepared liquid metal conductive electronics. Herein, a novel solidification strategy of liquid GaIn alloys by Ni doping and heat treatment is first reported, which can efficiently create a solid phase in the liquid metal and provide an effective solution for practical applications. Particularly, the liquid characteristic is preserved for conveniently fabricating different flexible electronic circuits, and then the solidification is carried out on prepared conductive patterns by heat treatment. The solidification mechanism is revealed by the interface chemical reaction between Ni and GaIn, creating the solid phase of intermetallic compound (Ga₄Ni₃ and InNi₃) during heat treatment. Moreover, a biphasic GaInNi can be obtained by regulating the atomic ratio of gallium, indium, and nickel. As a result, the obtained GaInNi possesses extremely low sheet resistance (15 ± 4.5 to 135 ± 2.5 mΩ sq^?1) and the variation of ΔR/R₀ exhibits low level (0–2) when strained up to 100%, which offers a promising strategy to prepare stretchable and reliable liquid metal electronics.     

耐蚀合金中TiN析出机制

摘要：TiN颗粒尺寸及其分布对耐蚀合金性能有明显的影响，因此有必要对TiN在铸坯中的分布及其析出行为进行研究。采用扫描电镜(SEM)、金相显微镜（OM）观察了TiN夹杂物在铸坯中的分布、尺寸及其形貌；基于热力学和动力学理论分析了耐蚀合金铸坯中TiN夹杂物的析出时机及其尺寸，结合试验结果和理论计算明确了TiN夹杂物在凝固后铸坯中的位置和尺寸与析出时机的关系，为控制TiN夹杂物提供理论指导。结果表明，冶炼过程中析出的TiN夹杂物尺寸较大，在凝固过程中被枝晶吞没，位于铸坯枝晶内和等轴晶内；微观偏析计算结果表明，在凝固分数为0.55时，TiN开始析出，最开始析出TiN夹杂物的逐渐长大，长大后的TiN易于被二次枝晶吞没，最终位于铸坯中的枝晶间和等轴晶内，后期析出的TiN则在枝晶间和等轴晶间。固相中析出的TiN夹杂物长大较慢，尺寸细小，最终位于奥氏体晶界。     

Probing the degenerate pattern growth of {100}<011> orientation in a directionally solidified Al-4.5 wt% Cu alloy

Degenerate pattern is a seemingly disordered morphology but it exhibits the inherently ordered crystal connected with tip-splitting and limited stability which makes it difficult to observe in the metallic system. Here we employ (100)[011] orientated planar-front seeds using directional solidification and reveal the fundamental origins of the degenerate pattern growth in an Al-4.5 wt% Cu alloy. We find that the spacing of the tip-splitting (λ) in the degenerate of the alloys followed a power law, λ∝V^−0.5, and the frequency (f) of the splitting was related to the growth velocity (V) by ƒ∝V^1.5. The dimensionless growth direction (θ/θ₀) increased monotonously and approached 0.6 with faster velocity, attributed to its anisotropy in the interface kinetics. Once growth velocity exceeded a threshold, two types of pattern transitions from degenerate to regular dendrites were proposed. One of them exhibited a random and chaotic mode and the other underwent a rotation in growth direction.     

定向长钻孔整体水力压裂增透技术在赵固二矿的应用

针对赵固二矿煤层透气性低、钻孔有效影响半径小，实施定向长钻孔代替底板岩巷进行区域瓦斯治理期间钻孔工程量大、瓦斯抽采效果不理想的问题。结合煤层赋存特征及钻孔施工情况，采用定向长钻孔整体水力压裂增透技术，理论分析了合理坐封位置、压裂参数，完成200 m煤巷条带一次整体压裂，最大泵注压力24.3 MPa、累计注水量1 613 m³。并基于煤层全水分变化，考察确定了单个钻孔压裂影响范围达到巷道两帮30 m，有效改善了煤体储层特性，提高了煤层瓦斯抽采效率。在实现定向钻孔对预抽煤巷条带可靠控制的同时，最大程度降低了钻孔工程量、缩短了瓦斯治理周期，为实现矿区“以孔代巷”及高效安全开采提供了技术支撑。     

Solidification of Be-free Ni-based dental alloy

A novel, Nb- and Si-rich and Be-free Ni-based alloy was cast by two methods of investment casting and continuous casting to study the microstructure evolution during solidification and its mechanical properties. The solidification of the alloy started with the primary crystallization of FCC-γ, followed by a binary eutectic reaction, with the formation of a heterogeneous constituent: FCC-γ+G-phase, which replaced the low-melting eutectic (FCC-γ+NiBe) in the Be-bearing alloys. AlNi₆Si₃ and γ′ formed during the terminal stages of solidification by investment casting, while the formation of AlNi₆Si₃ was suppressed by continuous casting. The Scheil solidification model agreed very well with the experimental results.