Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Nido-Hydroborate-Based Electrolytes for All-Solid-State Lithium Batteries

Hydroborate-based solid electrolytes have recently been successfully employed in high voltage, room temperature all-solid-state sodium batteries. The transfer to analogous lithium systems has failed up to now due to the lower conductivity of the corresponding lithium compounds and their high cost. Here LiB₁₁H₁₄ nido-hydroborate as a cost-effective building block and its high-purity synthesis is introduced. The crystal structures of anhydrous LiB₁₁H₁₄ as well as of LiB₁₁H₁₄-based mixed-anion solid electrolytes are solved and high ionic conductivities of 1.1 × 10⁻⁴ S cm⁻¹ for Li₂(B₁₁H₁₄)(CB₁₁H₁₂) and 1.1 × 10⁻³ S cm⁻¹ for Li₃(B₁₁H₁₄)(CB₉H₁₀)₂ are obtained, respectively. LiB₁₁H₁₄ exhibits an oxidative stability limit of 2.6 V versus Li⁺/Li and the proposed decomposition products are discussed based on density functional theory calculations. Strategies are discussed to improve the stability of these compounds by modifying the chemical structure of the nido-hydroborate cage. Galvanostatic cycling in symmetric cells with two lithium metal electrodes shows a small overpotential increase from 22.5 to 30 mV after 620 h (up to 0.5 mAh cm⁻²), demonstrating that the electrolyte is compatible with metallic anodes. Finally, the Li₂(B₁₁H₁₄)(CB₁₁H₁₂)  electrolyte is employed in a proof-of-concept half cell with a TiS₂ cathode with a capacity retention of 82% after 150 cycles at C/5.     

Solidification of Be-free Ni-based dental alloy

A novel, Nb- and Si-rich and Be-free Ni-based alloy was cast by two methods of investment casting and continuous casting to study the microstructure evolution during solidification and its mechanical properties. The solidification of the alloy started with the primary crystallization of FCC-γ, followed by a binary eutectic reaction, with the formation of a heterogeneous constituent: FCC-γ+G-phase, which replaced the low-melting eutectic (FCC-γ+NiBe) in the Be-bearing alloys. AlNi₆Si₃ and γ′ formed during the terminal stages of solidification by investment casting, while the formation of AlNi₆Si₃ was suppressed by continuous casting. The Scheil solidification model agreed very well with the experimental results.     

Design of tailored biodegradable implants: The effect of voltage on electrodeposited calcium phosphate coatings on pure magnesium

Magnesium, as a biodegradable metal, offers great potential for use as a temporary implant material, which dissolves in the course of bone tissue healing. It can sufficiently support the bone and promote the bone healing process. However, the corrosion resistance of magnesium implants must be enhanced before its application in clinical practice. A promising approach of enhancing the corrosion resistance is deposition of bioactive coating, which can reduce the corrosion rate of the implants and promote bone healing. Therefore, a well-designed substrate-coating system allowing a good control of the degradation behavior is highly desirable for tailored implants for specific groups of patients with particular needs. In this contribution, the influence of coating formation conditions on the characteristics of potentiostatically electrodeposited CaP coatings on magnesium substrate was evaluated. Results showed that potential variation led to formation of coatings with the same chemical composition, but very different morphologies. Parameters that mostly influence the coating performance, such as the thickness, uniformity, deposits size, and orientation, varied from produced coating to coating. These characteristics of CaP coatings on magnesium were controlled by coating formation potential, and it was demonstrated that the electrodeposition could be a promising coating technique for production of tailored magnesium-CaP implants.     

Structural Basis for Antimicrobial Activity of Lasiocepsin

Lasiocepsin is a unique 27‐residue antimicrobial peptide, isolated from Lasioglossum laticeps (wild bee) venom, with substantial antibacterial and antifungal activity. It adopts a welldefined structure consisting of two α‐helices linked by a structured loop. Its basic residues form two distinct positively charged regions on the surface whereas aliphatic side chains contribute to solvent‐accessible hydrophobic areas, thus emphasising the amphipathic character of the molecule. Lasiocepsin structurally belongs to the ShK family and shows a strong preference for anionic phospholipids; this is further augmented by increasing concentrations of cardiolipin, such as those found at the poles of bacterial cells. The membrane‐permeabilising activity of the peptide is not limited to outer membranes of Gram‐negative bacteria. The peptide interacts with phospholipids initially through its N terminus, and its degree of penetration is strongly dependent on the presence of cardiolipin.     

Development of a solid self-microemulsifying drug delivery system (SMEDDS) for solubility enhancement of naproxen

Context: Comparative evaluation of liquid and solid self-microemulsifying drug delivery systems (SMEDDS) as promising approaches for solubility enhancement.

Objective: The aim of this work was to develop, characterize, and evaluate a solid SMEDDS prepared via spray-drying of a liquid SMEDDS based on Gelucire® 44/14 to improve the solubility and dissolution rate of naproxen.

Material and methods: Various oils and co-surfactants in combination with Gelucire® 44/14 were evaluated during excipient selection study, solubility testing, and construction of (pseudo)ternary diagrams. The selected system was further evaluated for naproxen solubility, self-microemulsification ability, and in vitro dissolution of naproxen. In addition, its transformation into a solid SMEDDS by spray-drying using maltodextrin as a solid carrier was performed. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and X-ray diffraction (XRD) were used to evaluate the physical characteristics of the solid SMEDDS obtained.

Results: The selected formulation of SMEDDS was comprised of Miglyol 812®, Peceol?, Gelucire® 44/14, and Solutol® HS 15. The liquid and solid SMEDDS formed a microemulsion after dilution with comparable average droplet size and exhibited uniform droplet size distribution. In the solid SMEDDS, liquid SMEDDS was adsorbed onto the surface of maltodextrin and formed smooth granular particles with the encapsulated drug predominantly in a dissolved state and partially in an amorphous state. Overall, incorporation of naproxen in SMEDDS, either liquid or solid, resulted in improved solubility and dissolution rate compared to pure naproxen.

Conclusion: This study indicates that a liquid and solid SMEDDS is a strategy for solubility enhancement in the future development of orally delivered dosage forms.     

Production of stable amorphous form by means of spray drying

Spray drying is a very useful method for manufacturing of amorphous solid materials. This is mainly due to the possibility of fast solvent evaporation that leads to a rapid transformation of solution to a solid state. Besides evaporation kinetics, there are various process parameters that influence physical and chemical characteristics of such obtained material. The possibility of obtaining a stable amorphous structure of the active pharmaceutical ingredient in a spray dryer was examined. A solution of the hydrochloride crystalline structure of the active pharmaceutical ingredient in a mixture of water and acetonitrile was dried at different temperatures and flowrates of nitrogen used for atomization, as well as the flowrates of the solution. The influence of the process conditions on the properties of the product was analyzed. The final dried products were characterized and identified with a variety of analytical and physical methods. The results showed that a stable amorphous structure of the high purity active pharmaceutical ingredient is obtained, and that the optimal conditions of the process are defined. The amorphous structure is stable at temperatures below 200°C when it is transformed into a new crystal structure. Conditions of high relative air humidity lead to partial transformation.