Stable power supply of an independent power source for a remote island using a Hybrid Energy Storage System composed of electric and hydrogen energy storage systems

We propose a self-sustaining power supply system consisting of a “Hybrid Energy Storage System (HESS)” and renewable energy sources to ensure a stable supply of high-quality power in remote islands. The configuration of the self-sustaining power supply system that can utilize renewable energy sources effectively on remote islands where the installation area is limited is investigated. It is found that it is important to select renewable energy sources whose output power curve is close to the load curve to improve the efficiency of the system. The operation methods that can increase the cost-effectiveness of the self-sustaining power supply system are also investigated. It is clarified that it is important for increasing the cost effectiveness of the self-sustaining power supply system to operate the HESS with a smaller capacity of its components by setting upper limits on the output power of the renewable energy sources and cutting the infrequent generated power.     

IRS辅助的SWIPT系统中基于能效优先的波束成形设计与优化

以智能反射面(intelligent reflecting surface,IRS)辅助的无线携能通信(simultaneous wireless information and power transfer,SWIPT)系统为背景,研究了该系统中基于能效优先的多天线发送端有源波束成形与IRS无源波束成形联合设计与优化方法。以最大化接收端的最小能效为优化目标,构造在发送端功率、接收端能量阈值、IRS相移等多约束下的非线性优化问题,用交替方向乘子法(alternating direction method of multipliers,ADMM)求解。采用Dinkelbach算法转化目标函数,通过奇异值分解(singular value decomposition,SVD)和半定松弛(semi-definite relaxation,SDR)得到发送端有源波束成形向量。采用SDR得到IRS相移矩阵与反射波束成形向量。结果表明,该系统显著降低了系统能量收集(energy harvesting,EH)接收端的能量阈值。当系统总电路功耗为?15 dBm时,所提方案的用户能效为300 KB/J。当IRS反射阵源数与发送天线数均为最大值时,系统可达最大能效。     

Systematic analysis and multi-objective optimization of an integrated power and freshwater production cycle

This study represents the results of the analysis and optimization of an integrated system for cogenerating electricity and freshwater. This setup consists of a Solid Oxide Fuel cell (SOFC) for producing electricity. Unburned fuel of the SOFC is burned in the afterburner to increase the temperature of the SOFC's outlet gasses and operate a Gas turbine (GT) to produce additional power and operate the air compressor. At the bottom of this cycle, a combined setup of a Multi-Effect Desalination (MED) and Reverse Osmosis (RO) is considered to produce freshwater from the unused heat capacity of the GT's exhaust gasses. Also, a Stirling engine is used in the fuel supply line to increase the fuel's temperature. Using LNG and the Stirling engine will replace the fuel compressor with a pump which increases the system performance and eliminates the need for the expansion valve. To study the system performance a mathematical model is developed in Engineering Equation Solver (EES) program. Then, the system's simulated data from the EES has been sent to MATLAB to promote the best operating condition based on the optimization criteria. An energetic, exergetic, economic, and environmental analysis has been performed and a Non-dominated Sorting Genetic Algorithm (NSGA-II) is used to achieve the goal. The two-objective optimization is performed to maximize the exergetic efficiency of the proposed system while minimizing the system's total cost of production. This cost is a weighted distribution of the Levelized Cost of Electricity (LCOE) and Levelized Cost of freshwater (LCOW). The results showed that the exergetic and energetic efficiencies of the system can reach 73.5% and 69.06% at the optimum point. The total electricity production of the system is 99 MW. The production cost is 11.71 Cents/kWh, of which 1.04 Cents/kWh is emission-related and environmental taxes. The freshwater production rate is 42.44 kg/s which costs 4.38 USD/m³.     

多堆厂址始发事件分析探讨

多堆厂址一级概率安全评价（PSA）研究中，机组数目的增加使得建模工作量剧增，给整个核电厂的风险评估带来困难。结合已有基础，本文研究了多堆厂址始发事件分析的筛选方法，提出利用堆芯损伤频率（CDF）上下限值评估方法，分析厂址内不同机组数对厂址CDF的影响。结果表明，双机组厂址适合优先进行具体分析。针对双机组核电站，对多堆厂址内各始发事件进行筛选。结果表明，丧失厂外电、丧失热阱等事件适合建模分析，并对其他筛选结果给出后续分析建议，为多堆厂址一级PSA后续事故序列建模工作提供了重要基础。     

Bioinspired Triboelectric Soft Robot Driven by Mechanical Energy

A sustainable power source is a key technical challenge for practical applications of electrically responsive soft robots, especially the required voltage is over several thousand volts. Here, a practicable new technology, triboelectric soft robot (TESR) system with the primary characteristics of power source from mechanical energy, is developed. At its heart is TESR with bioinspired architectures made of soft-deformable body and two triboelectric adhesion feet, which is driven and accurately controlled through triboelectric effect, while reaching maximum crawling speeds of 14.9 mm s⁻¹ on the acrylic surface. The characteristics of the TESR, including displacement and force, are tested and simulated under the power of a rotary freestanding triboelectric nanogenerator (RF-TENG). Crawling of TESR is successfully realized on different materials surfaces and different angle slopes under the driven of RF-TENG. Furthermore, a real-time visual monitoring platform, in which TESR carries a micro camera to transmit images in a long narrow tunnel, is also achieved successfully, indicating that it can be used for fast diagnosis in an area inaccessible to human beings in the future. This study offers a new insight into the sustainable power source technologies suitable for electrically responsive soft robots and contributes to expanding the applicability of TENGs.     

Investigation of the Ga-Sb-S chalcogenide glass with low thermo-optic coefficient as an acousto-optic material

In this study, two series of Ga_xSb_40-xS₆₀ (x = 4, 6, 8, 10 mol%) and Ga_ySb₃₆S_64-y (y = 3, 5, 6 mol%) glasses were prepared and the relationship between their compositional and acousto-optic (AO) properties was investigated systematically for the first time. In the Ga_ySb₃₆S_64-y system, the AO figure of merit (M₂) increased as the Ga increased, and the maximum M₂ of the Ga₆Sb₃₆S₅₈ glass was 455.78 × 10^?18 s³/g, which is ～301 times greater than that of fused silica and ～2.5 times greater than that of As₂S₃ chalcogenide (ChG) glass at 1550 nm. However, its thermo-optic coefficients (dn/dT) varied greatly (32.1 × 10^?6 °C^?1–57.2 × 10^?6 °C^?1), and acoustic attenuations (α) at 10 MHz were high, from 5.446 dB/cm to 7.274 dB/cm. In the Ga_xSb_40-xS₆₀ glass system, the M₂ value and α at different ultrasonic frequencies gradually decreased with the improvement of Ga. Compared with the Ga_ySb₃₆S_64-y system, the Ga_xSb_40-xS₆₀ glass system had lower α (at 10 MHz) and dn/dT, which are 5.001 dB/cm–5.563 dB/cm and 17.3 × 10^?6 °C^?1–55.6 × 10^?6 °C^?1, respectively. These results provide a significant reference for the further development of novel ChG glasses and help expand their application fields.     

井下供电监控及防越级跳闸系统运用分析

以井下供电监控及防越级跳闸运用为对象开展探究。在分析矿井供电系统运行中现存主要问题的基础上,对供电监控与防越级跳闸系统整体应用的积极意义进行了分析和总结,希望能够让更多矿井技术人员了解供电监控及防越级跳闸系统的优越性,为其在矿井中的广泛推广普及提供便利,为煤矿行业更加高效地发展提供帮助。     

低功耗高性能的全MOS电压基准源设计

设计了一种基于亚阈值技术的全MOS电压基准源,采用共源共栅结构来增大PSRR,使用MOS管代替电阻,优化温度特性,使电路中大部分MOS管工作于亚阈值区。基于0.18μm CMOS工艺进行设计、版图绘制、和前、后仿真,在后仿真中得出相关参数值。对各参数做出详细分析,包括:一定温度范围内的温度系数;常温下基准输出电压;不同电源电压条件下的线性调整率、基准源静态电流及功耗,并对不同频率下的电源电压抑制比进行了对比。实验结果表明达到了低功耗高性能的设计目标。     

Computer‐aided design methodology for linearity enhancement of multiwatt GaN HEMT amplifiers using multiple parallel devices

This article presents a design methodology for linearizing GaN HEMT amplifiers based on splitting a large FET into multiple parallel FETs with same total gate periphery and by biasing them individually. By varying the biases, the magnitude and the phase of the IMD3 components at the output of FET changes. A detailed simulation methodology using commercial microwave CAD software is presented. Simulation results show that by biasing one device in Class AB and other(s) in deep Class AB mode, IMD3 components of parallel FETs can be made out of phase to each other leading to cancellation and improvement in linearity. Three prototype circuits were simulated using (a) a single 5 mm FET (1 × 5 mm), (b) two parallel 2.5 mm FETs (2 × 2.5 mm), and (c) four parallel 1.25 mm FETs (4 × 1.25 mm), for a total gate periphery of 5 mm, over the frequency range of 0.8 to 1.0 GHz. IMD3 improvement up to 20 dBc was achieved with the 4 × 1.25 mm circuit when the FET biases were optimized. Measurement results show improvement in linearity up to 20 dBc for 4 × 1.25 mm circuit. The proposed method improves linearity without a substantial penalty on the power consumption and is straightforward to implement.     

Benchmark value determination of energy efficiency indexes for coal-fired power units based on data mining methods

The operational optimisation of coal-fired power units is important for saving energy and reducing losses in the electric power industry. One of the key issues is how to determine the benchmark values of the energy efficiency indexes of the units. Therefore, a new framework for determining these benchmark values is proposed, based on data mining methods. First, the energy efficiency key performance indicators (KPIs) associated with the net coal consumption rate (NCCR) were selected based on the domain knowledge. Second, the decision-making samples with minimal NCCR were acquired with the fuzzy C-means (FCM) clustering algorithm, and the corresponding clustering centres were employed as the benchmark values. Finally, based on the support vector regression (SVR) algorithm, the target values of the NCCR were obtained with the KPIs as input, and the energy saving potential was evaluated by comparing the target values with the historical values of the NCCR. An actual on-duty 1000 MW unit was taken as study unit, and the results show that the energy saving potential is remarkable when the operators adjust the KPIs based on the calculated benchmark values.