高稳高效海上风电安装平台关键制造技术研究

海上风电作为可再生清洁能源之一,受到世界各国的高度重视与大力发展。我国将海上风电提升至解决能源危机、减缓气候变化、调整能源结构的国家战略高度,到2030年我国单位国内生产总值二氧化碳排放将比2005年下降65%以上,非化石能源占一次能源消费比重将达到25%左右。安装平台不足将是我国海上风电场无法如期建成投产的主要障碍。对自升自航式海上风电安装平台系列高端装备及其设计制造的三大技术难题——腿站立作业易“失稳”、大平台大跨距大倾覆力矩自升易“失控”、高空吊装巨型叶片逾百螺栓精准定位易“失准”,以及焊缝缺陷修复和局部裂纹损伤的激光锻造修复再制造进行了介绍,研制的具有不同规格的系列装备在中国、英国、丹麦、德国等国家的著名海上风电场建设应用情况良好。     

基于卓越工程师教育的频率特性分析课堂教学研究

频率特性分析在工程应用中具有重要的作用,在电路分析、模拟电子技术、信号与系统、自动控制理论等相关课程中都涉及到相关章节内容,在不同课程中如何根据工程应用和学生学习阶段把握具体的讲解内容和讲解方式非常重要。本文从频率特性的求解方法和具体物理意义角度开展在不同课程中讲解的方法,从时域和频域角度分别讨论其物理意义和具体的分析方法。通过渐进深化的教学过程和教学方法不断提高学生的知识掌握和应用技能,提高学生的工程意识、工程素质和工程创新能力,强化学生对于频率特性课程知识的综合应用能力。     

Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Turbulent boundary layer control with a spanwise array of DBD plasma actuators

The turbulent boundary layer control on NACA 0012 airfoil with Mach number ranging from 0.3 to 0.5 by a spanwise array of dielectric barrier discharge(DBD)plasma actuators by hot-film sensor technology is investigated.Due to temperature change mainly caused through heat produced along with plasma will lead to measurement error of shear stress measured by hot-film sensor,the correction method that takes account of the change measured by another sensor is used and works well.In order to achieve the value of shear stress change,we combine computational fluid dynamics computation with experiment to calibrate the hot-film sensor.To test the stability of the hot-film sensor,seven repeated measurements of shear stress at Ma = 0.3 are conducted and show that confidence interval of hot-film sensor measurement is from-0.18 to 0.18 Pa and the root mean square is 0.11 Pa giving a relative error 0.5％over all Mach numbers in this experiment.The research on the turbulent boundary layer control with DBD plasma actuators demonstrates that the control makes shear stress increase by about 6％over the three Mach numbers,which is thought to be reliable through comparing it with the relative error 0.5％,and the value is hardly affected by burst frequency and excitation voltage.     

机井自动化供水方案改进

针对民乐县农村人饮机井水位自动供水系统控制中存在的可靠性低、成本高等问题,文章结合深井泵提取地下水进行供水的实际情况,提出了软启动控制柜+浮球开关+微电脑时间控制器改进的思路和方法,运用效果良好。     

工艺参数对动态流量控制法挤压弯管应力的影响

采用有限元模拟和实验研究了挤压钛合金弯曲管件。通过实验验证了工件的形状和尺寸精度,并通过有限元模拟分析了工艺参数对挤出过程中变形体的平均压应力分布情况和挤出弯管件的曲率半径的影响规律。结果表明:有限元模拟中,弯管件的曲率半径误差为6.03%,弯管直径误差为3.82%;在靠近定径带处,平均压应力呈非均匀分布;在焊合腔内,靠近细分流孔区域的平均压应力小于靠近粗分流孔区域的平均压应力,平均压应力的大小顺序在通过粗、细分流孔前后相反;在模具结构固定不变时,弯管件的曲率半径随挤压速度的减小而增大,不随挤压温度的变化而变化。     

基于概率法的电力系统安全分析

为应对电力系统安全分析中的停机问题，基于概率法的方式，将常用的确定停机计算与加入了概率法的概率停机进行比较，研究了二者的区别与其在长期投资方向的不同。在进行电力系统停机分析时，通常会分别从确定停机与概率停机的角度出发，对其应急状态下的潮流进行计算。但前者的方法可能导致极低概率的停机事件被忽略，进而影响长期的资金投资。通过加入概率法的计算，使得对单个停机事件的判定由其具体的频率来确定，增加了系统运行的稳定性。     

激光在线测厚振动分析与精度优化

激光测厚具有安全可靠、测量精度高、测量范围大等优点,广泛应用于纸张、电池极片等薄膜类材料厚度的在线测量。带材宽幅方向扫描测厚时由于扫描架往复运动会产生机械振动,影响在线测厚精度。针对该问题,以锂离子电池极片厚度测量为例,使用双激光差动式测厚平台对电池极片和铜箔分别进行厚度测量,然后对测厚数据进行频谱分析,探究其振动规律的相似性,并基于频谱分析结果采用滑动带阻滤波方式对测厚数据进行处理,滤波后极片和铜箔的厚度极差分别降低了33.4%和73.8%,有效过滤了机械振动导致的测量误差,可满足极片和铜箔厚度测量的精度要求。     

采用温控和碘吸收池技术的发射激光稳频技术

多普勒测风激光雷达通过分析系统回波信号的多普勒频移反演出风速，为提高风场探测精度，从稳频技术方面展开研究。在稳频过程中，分别采取措施消除激光频率的长期漂移和短期抖动。针对激光频率的长期漂移，设计并研制了种子激光器温控箱，通过水浴的控温方式大大减小了激光频率的长期漂移，将激光频率稳定在±50 MHz以内；针对激光频率的短期抖动，采用以碘分子吸收池为核心器件的稳频系统，通过半导体控温方式对碘分子吸收池精确控温，控温精度达0.03 ℃，提高了稳频精度，将激光频率进一步稳定在±8 MHz以内，满足±10 MHz以内的设计精度要求。通过搭建多普勒测风激光雷达系统，对发射激光稳频装置进行系统验证，连续4组风场观测结果表明:系统探测高度为17 km，绝大部分方差在4 m/s以下，满足测风激光雷达测量指标的要求。