Effect of phosphogypsum on saline-alkalinity and aggregate stability of bauxite residue

A column experiment was conducted to investigate the effect of phosphogypsum (PG) on the saline- alkalinity, and aggregate stability of bauxite residue. Results showed that: with increasing leaching time, the concentrations of saline-alkali ions decreased while the concentration increased in bauxite residue leachate; compared with CK (control group) treatment, pH, electric conductivity (EC), exchangeable sodium percentage (ESP), sodium absorption ratio (SAR), and exchangeable Na⁺ content of bauxite residue were reduced following PG treatment; average particle sizes in aggregates following CK and PG treatments were determined to be 155 and 193 nm, respectively. SR-μCT test results also confirmed that bauxite residue following PG treatment acquired larger aggregates and larger pore diameter. These results indicate that the PG treatment could significantly modulate the saline-alkalinity, and simultaneously enhance aggregate stability of bauxite residue, which provides a facile approach to reclaim bauxite residue disposal areas.     

Simultaneous process optimization and heat integration based on rigorous process simulations

This paper introduces a simultaneous process optimization and heat integration approach, which can be used directly with the rigorous models in process simulators. In this approach, the overall process is optimized utilizing external derivative-free optimizers, which interact directly with the process simulation. The heat integration subproblem is formulated as an LP model and solved simultaneously during optimization of the flowsheet to update the minimum utility and heat exchanger area targets. A piecewise linear approximation for the composite curve is applied to obtain more accurate heat integration results. This paper describes the application of this simultaneous approach for three cases: a recycle process, a separation process and a power plant with carbon capture. Case study results indicate that this simultaneous approach is relatively easy to implement and achieves higher profit and lower operating cost and, in the case of the power plant example, higher net efficiency than the sequential approach.     

全尾砂和废石联合胶结充填体最佳配比及应用

针对红岭铅锌矿分级充填骨料来源不足、地表废石堆积污染环境的情况,提出将该矿选厂产生的全尾砂和地表废石作为充填骨料的联合胶结充填方案。分别测试了全尾砂和地表废石的物理化学性质,验证了碎石和全尾砂作为联合充填骨料的可行性。通过充填配比试验,分析了不同配比全尾砂废石充填体强度特性,得出了最佳充填配比。结果表明,充填试块的强度随灰砂比减小而减小,随养护龄期增加呈增大趋势,随充填料浆质量浓度增大而增大,最佳配比为: 胶结充填灰砂比1∶8、普通充填灰砂比1∶12,全尾砂∶废石配比4∶6,质量浓度78%。根据研究结果,在红岭铅锌矿进行了全尾砂废石充填技术工业应用,证实该技术可行。     

Mixture ratio modeling of dynamic systems

Any knowledge extraction relies (possibly implicitly) on a hypothesis about the modelled-data dependence. The extracted knowledge ultimately serves to a decision-making (DM). DM always faces uncertainty and this makes probabilistic modelling adequate. The inspected black-box modeling deals with “universal” approximators of the relevant probabilistic model. Finite mixtures with components in the exponential family are often exploited. Their attractiveness stems from their flexibility, the cluster interpretability of components and the existence of algorithms for processing high-dimensional data streams. They are even used in dynamic cases with mutually dependent data records while regression and auto-regression mixture components serve to the dependence modeling. These dynamic models, however, mostly assume data-independent component weights, that is, memoryless transitions between dynamic mixture components. Such mixtures are not universal approximators of dynamic probabilistic models. Formally, this follows from the fact that the set of finite probabilistic mixtures is not closed with respect to the conditioning, which is the key estimation and predictive operation. The paper overcomes this drawback by using ratios of finite mixtures as universally approximating dynamic parametric models. The paper motivates them, elaborates their approximate Bayesian recursive estimation and reveals their application potential.     

Thermal imaging of time-varying longitudinal defects in the internal coating of a tube

We deal with the mathematical model of the incremental degradation of the internal coating (e.g. a polymeric material) of a metallic pipe in which a fluid flows relatively fast. The fluid drags solid impurities so that longitudinal scratches, inaccessible to any direct inspection procedure, are produced on the coating. Time evolution of this kind of defects can be reconstructed from the knowledge of a sequence of temperature maps of the external surface. The time-varying orthogonal section of this damaged interface is determined as a function of time and polar angle through the identification of a suitable effective heat transfer coefficient by means of Thin Plate Approximation.     

人工砂混凝土性能试验研究

采用正交试验方法配制了不同人工砂取代率、石粉含量、粉煤灰含量的混凝土, 对比了每组混凝土的坍落度, 研究了3 d、28 d龄期混凝土的抗压性能。结果表明: 最优配比的人工砂取代率、石粉含量和粉煤灰含量分别为10%、3%和5%, 此时28 d抗压强度为40.1 MPa, 满足30 MPa的混凝土设计强度。     

LTE系统多小区上行联合功控算法

针对传统的小区内开环功率控制算法通常以提升本小区的吞吐量性能为目标，忽略了当前小区用户对邻小区用户同频干扰的问题，为提升边缘用户性能的同时兼顾系统整体性能，提出了一种LTE系统小区间上行联合功率控制（UJPC）算法。该算法采用单基站三扇区为系统模型，以最优化系统吞吐量比例公平函数为目标，首先根据最小信干噪比（SINR）约束值和用户最大发射功率这两个约束条件得到相应的数学优化模型，然后采用连续凸近似的方法求解优化问题得出各个基站所管辖的小区内所有用户的最优发射功率。仿真结果表明，与基准的开环功控方案相比，联合功控方案在保证系统平均频谱利用率的情况下能够较大幅度地提高小区边缘频谱利用率，其最佳性能增益能达到50%。     

随车起重机伸缩臂截面多目标优化

为了提高某火箭炮弹药装填车随车起重机伸缩臂的结构刚度,减轻结构质量,建立了随车起重机伸缩臂参数化模型,并对伸缩臂在水平受载状态下进行仿真分析。以伸缩臂截面尺寸参数为设计变量,借助最优拉丁超立方试验设计建立样本空间,构造响应面多项式函数近似模型。在此基础上,利用NSGA-Ⅱ型遗传算法对伸缩臂自身重量、挠度进行多目标优化。优化结果表明:伸缩臂质量减轻了24.5%,减重效果明显。文中所采用的将参数化建模、有限元分析和数值寻优相结合的优化方法,可为起重机伸缩臂截面优化提供一定的参考。     

Range Assignment for Biconnectivity and k-Edge Connectivity in Wireless Ad Hoc Networks

Depending on whether bidirectional links or unidirectional links are used for communications, the network topology under a given range assignment is either an undirected graph referred to as the bidirectional topology, or a directed graph referred to as the unidirectional topology. The Min-Power Bidirectional (resp., Unidirectional) k-Node Connectivity problem seeks a range assignment of minimum total power subject to the constraint that the produced bidirectional (resp. unidirectional) topology is k-vertex connected. Similarly, the Min-Power Bidirectional (resp., Unidirectional) k-Edge Connectivity problem seeks a range assignment of minimum total power subject to the constraint the produced bidirectional (resp., unidirectional) topology is k-edge connected. The Min-Power Bidirectional Biconnectivity problem and the Min-Power Bidirectional Edge-Biconnectivity problem have been studied by Lloyd et al. [23]. They show that range assignment based the approximation algorithm of Khuller and Raghavachari [18], which we refer to as Algorithm KR, has an approximation ratio of at most 2(2 – 2/n)(2 + 1/n) for Min-Power Bidirectional Biconnectivity, and range assignment based on the approximation algorithm of Khuller and Vishkin [19], which we refer to as Algorithm KV, has an approximation ratio of at most 8(1 – 1/n) for Min-Power Bidirectional Edge-Biconnectivity. In this paper, we first establish the NP-hardness of Min-Power Bidirectional (Edge-) Biconnectivity. Then we show that Algorithm KR has an approximation ratio of at most 4 for both Min-Power Bidirectional Biconnectivity and Min-Power Unidirectional Biconnectivity, and Algorithm KV has an approximation ratio of at most 2k for both Min-Power Bidirectional k-Edge Connectivity and Min-Power Unidirectional k-Edge Connectivity. We also propose a new simple constant-approximation algorithm for both Min-Power Bidirectional Biconnectivity and Min-Power Unidirectional Biconnectivity. This new algorithm applies only to Euclidean instances, but is best suited for distributed implementation. A preliminary version of this work appeared in the proceedings of the 2nd International Conference on AD-HOC Network and Wireless (Adhoc-Now 2003). Research performed in part while visiting the Max-Plank-Institut fur Informatik. Gruia Calinescu is an Assistant Professor of Computer Science at the Illinois Institute of Technology since 2000. He held postdoc or visiting researcher positions at DIMACS, University of Waterloo, and Max-Plank Institut fur Informatik. Gruia has a Diploma from University of Bucharest and a Ph.D. from Georgia Insitute of Technology. His research interests are in the area of algorithms. Peng-Jun Wan has joined the Computer Science Department at Illinois Institute of Technology in 1997 and has been an Associate Professor since 2004. He received his Ph.D. in Computer Science from University of Minnesota in 1997, M.S. in Operations Research and Control Theory from Chinese Academy of Science in 1993, and B.S. in Applied Mathematics from Tsinghua University in 1990. His research interests include optical networks and wireless networks.