川中地区侏罗系沙溪庙组致密气处理和解释关键技术与应用

四川盆地蕴含丰富的致密砂岩气资源，近期利用高精度三维资料开展侏罗系沙溪庙组河道砂体勘探取得突出成效。沙溪庙组河道砂体具有横向变化快、储层非均质性强的特点，因此提高河道砂体的边界识别及其含气性预测精度是致密气地震勘探的关键。通过开展AVO特征低频保护的“六分法”（分类、分频、分时、分域、分步和分区）高保真叠前去噪、近地表Q补偿和OVT域叠前时间偏移等技术攻关，形成了一套针对川中地区侏罗系沙溪庙组致密气藏的“双高”（高保真、高分辨率）地震处理技术，并创新应用“双亮点”属性及多波、多分量砂体含气性地震预测等解释技术，提高了含气砂体预测精度。该技术系列在川中沙溪庙组致密气预测应用成果显著，地震数据频带得到了拓宽，低频信息更加丰富，资料信噪比明显提升，河道边界及其含气性预测的精度大幅提高，钻井成功率超过83%，应用成果有力地支撑了该地区沙溪庙组致密气的增储上产。     

Detailed analysis on thermal,microstructural, mechanical,and morphological features of side chain liquid crystalline polymer/isotactic polypropylene graft copolymers: Effect of grafted and ungrafted polymer units

The main scope of this comprehensive study is to investigate the effects of poly(p-benzophenoneoxycarbonylphenyl acrylate), poly(BPOCPA), which presenting as only graft units or both graft and ungrafted units in the matrix, on the fundamental features of isotactic polypropylene (IPP). The graft copolymerization of BPOCPA onto IPP was performed with the aid of bulk melt polymerization at varying monomer content levels ranging from 5% to 40%. The thermal behavior, crystal quality, mechanical performance, and surface morphology of the samples were investigated by means of differential scanning calorimeter, X-ray diffractometer (XRD), universal mechanical test, and scanning electron microscope (SEM) techniques. Thermal analyses depicted that there existed the noteworthy enhancements in both crystalline melting temperatures and percent crystallinities of matrix polymers. Furthermore, according to XRD results, a and b parameters increased significantly at low percentages of the graft units, while the parameter c decreased in all products in consistence with the content. As for the mechanical characterization, the grafting led to remarkable improvements in modulus, tensile and impact strength of the products. SEM micrographs indicated that the samples were completely homogeneous without any phase separation and the products exhibited brittle nature with some ductility.     

基于电机效率的纯电动汽车传动系统参数匹配研究

为降低能耗、提高续航里程,本文提出了以提高电机效率为目标的纯电动汽车三档变速传动方案.首先,在分析电机工作特性的基础上提出了三档传动系统参数匹配方法;然后以某纯电动汽车为研究对象,对其驱动系统进行了改动:方案一在不改变原车型动力系统参数的情况下将传动系统由一档改为三档,并运用所提出的方法确定各档位的传动比;方案二在满足整车动力性指标要求下对电机重新选型并匹配三档传动系统;最后利用ADVISOR软件进行NEDC工况仿真分析.结果表明:在不改变原车型动力系统参数的情况下,采用三档传动可使整车的动力性和经济性都有一定的提升,续航里程提高了 9.2％,百公里电耗降低了 1.28 kW·h;重新选型电机后,采用三档传动续航里程提高了 14.1％,百公里电耗降低了 1.87kW·h.     

600MW机组锅炉后屏过热器泄漏原因分析和预防

某电厂600 MW直接空冷机组锅炉后屏过热器泄漏停机处理完成后启动再次泄漏.通过检查和分析,后屏过热器第1次泄漏是由于异种钢焊口焊接质量差,第2次泄漏是由于第1次泄漏停机后未采用热炉带压放水和第2次启动过程中操作不当,导致后屏过热器形成水塞,造成局部短时过热爆管,并提出了消除方法和预防措施.     

基于全局优化与深度学习的条形码识别方法

提出了一种在深度神经网络的基础上结合全局优化方法的条形码识别算法,利用卷积循环网络提取出条码中各字元的特征并进行分类,较传统方法具有更强的适应性与泛化能力,再进一步结合全局优化的方法,以达到充分利用条码结构性先验信息的目的,能显著提升方法的效果,尤其是将全局优化方法引入到神经网络中进行端到端学习,不仅保持了两者的优势同时还进一步提高了识别精度.实验结果证明了所提方法的有效性,达到约99.48％的识别精度,超越了传统的图像处理方法.     

Corrosion behaviour of Mg-Gd-Y-Zn-Ag alloy components with different sizes after cooling

The corrosion behaviour of Mg-6Gd-3Y-1Zn-0.3Ag (wt.%) alloy components with different sizes after cooling was investigated. The alloys in the small components (SC) cooled fast, which were composed of α-Mg matrix and coarse long-period stacking ordered (LPSO) phases. The alloys in the large components (LC) cooled slowly, and there were thin lamellar LPSO phases precipitating inside the grains, except for α-Mg matrix and coarse LPSO phases. The hydrogen evolution test revealed that the corrosion rate of LC sample was higher than that of SC sample. Electrochemical impedance spectroscopy (EIS) test showed that the surface film on LC alloys provided worse protection. The corrosion morphologies indicated that the precipitation of the thin lamellar LPSO phases in LC sample caused severe micro-galvanic corrosion, which accelerated the rupture of the surface film.     

Research on the formation mechanism of big data technology cooperation networks: empirical evidence from China

Scientometrics - The purpose of the present paper is to investigate the formation mechanism of big data technology cooperation networks by considering the combined effect of three key factors,...     

南方地区造纸车间钢屋面保温厚度的计算与分析

本文从内表面防结露、夏季隔热2个角度出发，对夏热冬冷及夏热冬暖地区代表城市采用的钢结构屋面的保温（隔热）层厚度进行计算分析。研究表明，在夏季室内温、湿度达到某一状态时，隔热厚度要大于冬季防结露的保温厚度。因此，夏热冬冷地区的造纸车间钢屋面保温层厚度应按夏季隔热计算确定，并进行冬季防结露验算；夏热冬暖地区按照冬季防结露计算即可。