高面板坝全寿命周期变形控制方法及应用

高面板坝的变形对面板的安全运行有着特别重要的影响，国内外已建的高面板坝工程中，因坝体变形大导致防渗面板挤压破损，坝体渗漏量大的实例较多，不得不降低水库水位进行修复处理，造成较大的经济损失乃至给大坝的长期运行留下安全隐患。通过发生挤压破损的实例分析，发现变形控制缺乏系统性是发生面板挤压破损的主要因素，为预防面板破损，系统提出了“控制坝体总变形，转化有害变形，适应纵向变形”的坝体变形控制方法，并在使用软硬岩混合料筑坝的董箐面板堆石坝中得到的应用，取得了良好效果，该工程运行至今达十余年，未见面板有挤压破损迹象，该方法对建设200 m以上乃至300 m级超高面板坝具有重要借鉴意义。     

高效液相色谱法测定化妆品中依克多因的含量

建立高效液相色谱法测定化妆品中依克多因的分析方法,采用Agilent Poroshell 120 EC-C₁₈色谱柱（100 mm×3.0 mm,2.7μm）分离,以甲醇和p H为3.0的40 mmol/L磷酸二氢钠-10 mmol/L 1-庚烷磺酸钠缓冲溶液梯度洗脱,流速0.8 m L/min,柱温30℃,检测波长210 nm。采用外标法定量测定化妆品中的依克多因含量。结果表明,依克多因在5～800 mg/L的质量浓度范围内呈现良好线性关系,相关系数为0.999 8,方法的检出限和定量限分别为0.3和1.0 mg/L。该方法具有分离效率高、分析时间短、节省溶剂等优点,解决了依克多因在C₁₈色谱柱上保留弱的问题。     

Experimental and Numerical Investigation of a Novel Spiral Micromixer with Sinusoidal Channel Walls

A novel spiral micromixer with sinusoidal channel walls was designed to enhance the mixing index in the low to intermediate Reynolds number range (1 < Re < 100). To analyze the fluid flow, a set of numerical simulations were performed using the finite-difference method. The microchip was fabricated from polydimethylsiloxane, employing the soft-lithography technique. The degree of mixing was increased by 99.11 % when using the proposed micromixer, compared to 59.44 % for a simple spiral micromixer. The introduced microchannel drastically reduced the mixing length, increasing the mixing index of a 0.5-loop spiral-sinusoidal microchannel compared to that of the simple spiral microchannel with 1.5 loops. The mixing index of the 3-loop mixer was higher than that of the microchannel with 1.5 loops, and its pressure drop was increased.     

Statistical optimization of operating parameters of microbial electrolysis cell treating dairy industry wastewater using quadratic model to enhance energy generation

The performance of Microbial electrolysis cell (MEC) is affected by several operating conditions. Therefore, in the present study, an optimization study was done to determine the working efficiency of MEC in terms of COD (chemical oxygen demand) removal, hydrogen and current generation. Optimization was carried out using a quadratic mathematical model of response surface methodology (RSM). Thirteen sets of experimental runs were performed to optimize the applied voltage and hydraulic retention time (HRT) of single chambered batch fed MEC operated with dairy industry wastewater. The operating conditions (i.e) an applied voltage of 0.8 V and HRT of 2 days that showed a maximum COD removal response was chosen for further studies. The MEC operated at optimized condition (HRT- 2 days and applied voltage- 0.8 V) showed a COD removal efficiency of 95 ± 2%, hydrogen generation of 32 ± 5 mL/L/d, Power density of 152 mW/cm² and current generation of 19 mA. The results of the study implied that RSM, with its high degree of accuracy can be a reliable tool for optimizing the process of wastewater treatment. Also, dairy industry wastewater can be considered to be a potential source to generate hydrogen and energy through MEC at short HRT.     

Numerical modeling of hydrogen catalytic reactions over a circular bluff body

This paper was intended to delineate numerical research for hydrogen catalytic combustion over a circular cylinder. The wire/rod-type catalytic reactor is a simple geometry reactor with an economical design with less pressure loss. For the single rod in the reaction channel, the flow characteristic and the difference of conversion efficiency between non-gas-phase reaction and gas-phase reaction have been delineated in the present study. The flow field and the chemical reactions were numerically modeled using 2D Large Eddy Simulation combined with the gas-phase and surface reaction mechanisms. The results show that the current numerical simulation has been validated to precisely predict the vortex shedding and its frequency in the cold flows. Despite the variation trends being dominated by the upstream flow, the vortex shedding phenomena were affected by the flue gas generated from the rod surface. It can be seen from the linear relationship between the vortex shedding frequency of reacting flow and Reynolds Number. It is noted that the vortex shedding vanished if the gas-phase reaction was ignited in the reaction channel. In addition, the geometric modified conversion efficiency was proposed to delineate an indicator that could be potential for the optimization of rod-type catalytic reactor. In summary, the fundamental study of a rod in a 2D flow channel can provide information for optimizing the catalytic design or the rod array arrangement in the reactor. Moreover, the rod can also be a partial catalytic flame holder to ignite and stabilize the gas-phase reaction. The obtained results could be the potential for practical applications of rod-type catalytic combustion, catalytic gas turbine, hydrogen generation, partially catalytic reaction flame holder, and other catalytic reactions that can be appreciated.     

Microscopic high-speed video observation of oxygen bubble generation behavior and effects of anode electrode shape on OER performance in alkaline water electrolysis

An important difficulty associated with alkaline water electrolysis is the rise in anode overpotential attributable to bubble coverage of the electrode surface. For this study, a system with a high-speed video camera was developed, achieving in-situ observation of bubble generation on an electrode surface, monitoring an area of 1.02 mm² at 6000 frames per second. The relation between polarization curve (current density up to 3.0 A cm^?2) and oxygen bubble generation behavior on nickel electrodes having cylindrical wires and rectangular wires of different sizes (100–300 μm) was clarified. The generated bubbles slide upward, contacting the electrode surface and detaching at the top edge. Observations indicate that small electrodes have short bubble residence time and thin bubble covering layer on the electrode. As a result, the small electrode diameter contributes to smaller overpotential at high current density.     

Hydrogen-rich gas generation via the exhaust gas-fuel reformer for the marine LNG engine

Reformed exhaust gas recirculation technology has attracted great attention in internal combustion engines. A platform of an exhaust gas-fuel reformer connected with the marine LNG engine was set up for generating on-board hydrogen. Based on the platform, effects of the methane to oxygen ratio (M/O) and reformed exhaust gas ratio (R_EG) from the reformer and excess air ratio (λ) from the engine on the components, hydrogen yield, thermal efficiency and reforming process of the reformer were experimentally investigated. Results shown that hydrogen-rich gases (reformate) can be generated by reforming the mixture of engine exhaust gas (about 400 °C) and methane supplied via the reformer with Ni/Al₂O₃ catalyst, and the hydrogen concentration of reformate was between 6.2% and 12.6% by volume. The methane supplied rate and λ affected the components and temperature of the reactant in the reformer, while R_EG changed the gas hour space velocity during the exhaust gas-fuel reforming processes, resulting in the difference in the components of the reformate and thermal efficiency. At the present experimental condition, the highest H₂ concentration reformate was generated under the M/O of 2.0, λ of 1.55 and R_EG of 6%.     

A novel design for humidifying an open-cathode proton exchange membrane fuel cell using anode purge

The low performance of open-cathode proton-exchange-membrane fuel cells (OCPEMFCs) is attributed to the low-humidity ambient air supplied to the cathode using electric fans. To improve the OCPEMFC performance, this paper proposes a novel humidification method by collecting water purged from the anode and supplying it to the open cathode. The OCPEMFC performance is evaluated at various humidifier distances from the cathode inlet, and it is compared with that where no humidifier is used when the OCPEMFC operates under three different current levels of 1, 5, and 8 A. The results show that the novel design improves the stack power, and optimal performance is achieved at a humidifier distance of 2 cm. The energy efficiency achieves an improvement between 1.4% and 1.8% when a humidifier is used.     

Feeding behavior parameters and temporal patterns in mid-lactation Holstein cows across a range of residual feed intake values

Residual feed intake (RFI) is a measurement of the difference between actual and predicted feed intake when adjusted for energy sinks; more efficient cows eat less than predicted (low RFI) and inefficient cows eat more than predicted (high RFI). Data evaluating the relationship between RFI and feeding behaviors (FB) are limited in dairy cattle; therefore, the objective of this study was to determine daily and temporal FB in mid-lactation Holstein cows across a range of RFI values. Mid-lactation Holstein cows (n = 592 multiparous; 304 primiparous) were enrolled in 17 cohorts at 97 ± 26 d in milk (± standard deviation), and all cows within a cohort were fed a common diet using automated feeding bins. Cow RFI was calculated as the difference between predicted and observed dry matter intake (DMI) after accounting for parity, days in milk, milk energy, metabolic body weight and change, and experiment. The associations between RFI and FB at the level of meals and daily totals were evaluated using mixed models with the fixed effect of RFI and the random effects of cow and cohort. Daily temporal FB analyses were conducted using 2-h blocks and analyzed using mixed models with the fixed effects of RFI, time, RFI × time, and cohort, and the random effect of cow (cohort). There was a positive linear association between RFI and DMI in multiparous cows and a positive quadratic relationship in primiparous cows, where the rate of increase in DMI was less at higher RFI. Eating rate, DMI per meal, and size of the largest daily meal were positively associated with RFI. Daily temporal analysis of FB revealed an interaction between RFI and time for eating rate in multiparous and primiparous cows. The eating rate increased with greater RFI at 11 of 12 time points throughout the day, and eating rate differed across RFI between multiple time points. There tended to be an interaction between RFI and time for eating time and bin visits in multiparous cows but not primiparous cows. Overall, there was a time effect for all FB variables, where DMI, eating time and rate, and bin visits were greatest after the initial daily feeding at 1200 h, increased slightly after each milking, and reached a nadir at 0600 h (6 h before feeding). Considering the relationship between RFI and eating rate, additional efforts to determine cost-effective methods of quantifying eating rate in group-housed dairy cows is warranted. Further investigation is also warranted to determine if management strategies to alter FB, especially eating rate, can be effective in increasing feed efficiency in lactating dairy cattle.     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。