镁合金网格壁板压弯成形数值模拟及实验研究

为探索镁合金整体壁板压弯成形的可行性,以及镁合金壁板压弯成形过程中金属的流动规律,对AZ31镁合金网格壁板压弯成形进行了数值模拟和实验研究。建立了有限元数值模拟的几何模型,采用有限元计算软件对AZ31镁合金网格壁板压弯成形过程进行了数值模拟研究,分析了镁合金网格壁板压弯成形中的温度场、应变场、应力场、破坏系数等的分布规律。确定了合适的AZ31镁合金壁板压弯成形工艺参数,并对镁合金网格壁板压弯成形进行了实验研究,获得了合格的镁合金网格壁板弯曲件,并分析了镁合金网格壁板成形件尺寸精度,模拟结果与实验结果相吻合,最大相对误差为16.7%。     

Improved one-dimensional beam model for unbalanced composite single-lap joint

An analytical nonlinear solution was provided for unbalanced composite single-lap joint (CSLJ) using an improved one-dimensional beam model, which incorporated the effect of bending–tension coupling. The bending–tension coupling stiffness was introduced to characterize the coupling bending and tension behavior induced by the un-symmetric stacking sequence of composite laminates. The governing differential equations captured the bending–tension coupling behavior and the geometrically nonlinear features were constructed based on the displacement compatibility conditions of flexible interface. The transverse deformation in overlap region, edge moment factors and adhesive stress distributions for the unbalanced CSLJ with inflexible, intermediate flexibility and flexible adhesive can be determined by the present one-dimensional beam model. The accuracy of the present model was validated by the comparison with nonlinear finite element model. The effect of bending–tension coupling on edge moment factors and peak values of adhesive stresses was shed light on with the present model.     

Evaluation of dynamic modulus measurement for C/C-SiC composites at different temperatures

The determination of elastic properties at application temperature is fundamental for the design of fibre reinforced ceramic composite components. An attractive method to characterize the flexural modulus at room and high temperature under specific atmosphere is the nondestructive Resonant Frequency Damping Analysis (RFDA). The objective of this paper was to evaluate and validate the modulus measurement via RFDA for orthotropic C/C-SiC composites at the application temperature. At room temperature flexural moduli of C/C-SiC with 0/90° reinforcement were measured under quasi-static 4-point bending loads and compared with dynamic moduli measured via RFDA longitudinally to fibre direction. The dynamic modulus of C/C-SiC was then measured via RFDA up to 1250°C under flowing inert gas and showed an increase with temperature which fitted with literature values. The measured fundamental frequencies were finally compared to those resulting from numerical modal analyses. Dynamic and quasi-static flexural moduli are comparable and the numerical analyses proved that bending modes are correctly modeled by means of dynamic modulus measured via RFDA. The nondestructive RFDA as well as the numerical modeling approach are suitable for evaluation of C/C-SiC and may be transferred to other fibre reinforced ceramic composite materials.     

TiO2-rutile/anatase homojunction with enhanced charge separation for photoelectrochemical water splitting

The mismatched interfaces of heterojunction usually have lots of defects, deriving in recombination of generated electron-hole pairs. On the other hand, homojunction interfaces are considered to be beneficial to the separation of charge carriers due to the similar characteristics in two sides of homojunction. TiO₂ have rutile and anatase two typical photoactive phases in nature. In this work, TiO₂-rutile/anatase (TiO₂-R/A) homojunction photoanode is fabricated by in situ growth of anatase TiO₂ on TiO₂-R surface. By contrast with TiO₂-rutile/rutile (TiO₂-R/R) photoanode, TiO₂-R/A displays higher photocurrent density (1.70 mA cm^?2 at 0.6 V vs. SCE). Deep insight into the mechanism suggests that TiO₂-R/A homojunction has intense band bending and enhanced surface area, which facilitate the charge separation and transmission. This study offers some novel insights to design and fabricate semiconductors photoanodes for highly efficient photocatalytic reactions.     

Bulging in incremental sheet forming of cold bonded multi-layered Cu clad sheet: Influence of forming conditions and bending

Bulge is a defect that causes geometrical inaccuracy and premature failure in the innovative incremental sheet forming (ISF) process. This study has two-fold objectives: (1) knowing the bulging behavior of a Cu clad tri-layered steel sheet as a function of forming conditions, and (2) analyzing the bending effect on bulging in an attempt to identify the associated mechanism. A series of ISF tests and bending analysis are performed to realize these objectives. From the cause-effect analysis, it is found that bulge formation in the layered sheet is sensitive to forming conditions in a way that bulging can be minimized utilizing annealed material and performing ISF with larger tool diameter and step size. The bending under tension analysis reveals that the formation of bulge is an outgrowth of bending moment that the forming tool applies on the sheet during ISF. Furthermore, the magnitude of bending moment depending upon the forming conditions varies from 0.046 to 10.24 N·m/m and causes a corresponding change in the mean bulge height from 0.07 to 0.91 mm. The bending moment governs bulging in layered sheet through a linear law. These findings lead to a conclusion that the bulge defect can be overcome by controlling the bending moment and the formula proposed can be helpful in this regards.     

Möbius变换下四次有理抛物-PH曲线的C2 Hermite插值

目的 曲线插值问题在机器人设计、机械工业、航天工业等诸多现代工业领域都有广泛的应用，而已知端点数据的Hermite插值是计算机辅助几何设计中一种常用的曲线构造方法，本文讨论了一种偶数次有理等距曲线，即四次抛物-PH曲线的C² Hermite插值问题。方法 基于M bius变换引入参数，利用复分析的方法构造了四次有理抛物-PH曲线的C² Hermite插值，给出了具体插值算法及相应的Bézier曲线表示和控制顶点的表达式。结果 通过给出"合理"的端点插值数据，以数值实例表明了该算法的有效性，所得12条插值曲线中，结合最小绝对旋转数和弹性弯曲能量最小化两种准则给出了判定满足插值条件最优曲线的选择方法，并以具体实例说明了与其他插值方法的对比分析结果。结论 本文构造了M bius变换下的四次有理抛物-PH曲线的C² Hermite插值，在保证曲线次数较低的情况下，达到了连续性更高的插值条件，计算更为简单，插值效果明显，较之传统奇数次PH曲线具有更加自然的几何形状，对偶数次PH曲线的相关研究具有一定意义。     

Co/Al金属在聚晶立方氮化硼中的作用及加工适用性

通过正交试验和切削试验相结合的方法,检测聚晶立方氮化硼(PCBN)烧结体的硬度和强度,分析并观察烧结体组元相互熔渗状况以及微观形貌,探索了Co/Al金属对PCBN烧结体的影响以及不同结合剂含量PCBN的加工适应性。试验结果表明:CBN含量和Co含量对PCBN的抗弯强度和硬度影响显著;在刀具材料的选择上,高PCBN浓度的刀具适合加工灰铸铁,低PCBN浓度的刀具适合加工淬硬钢;Co/Al金属能够通过高温高压在PCBN层和硬质合金基体之间进行相互熔渗,导致PCBN层在距硬质合金10~20μm处Co含量达到最大值;PCBN的失效为穿晶断裂方式。     

[成形过程的数据挖掘与深度学习方法]基于机器学习的管材弯曲回弹有效预测与补偿

采用基于优化的误差反向传播(BP)神经网络的机器学习算法建模，提出了考虑材料参数、几何参数等多因素的弯管回弹精确预测和高效控制方法。该方法通过引入非线性惯性权重及遗传算法的杂交算子，改进了粒子群优化(PSO)算法，进而通过改进的PSO算法对BP神经网络进行优化，构建了基于改进的PSO-BP神经网络机器学习回弹预测和补偿模型。以多种规格的铝合金数控弯管构件为对象，将实际生产中不同规格、批次、成形参数下回弹数据作为训练样本，实现了所建机器学习预测模型的应用验证。所建模型获得的预测结果平均相对误差为6.3%，与未优化的BP神经网络等传统模型相比，预测精度最大提高了18.5%，计算时间可从1.5 h缩短至300 s，同时实现了回弹预测与补偿精度以及计算效率的显著提高。