深共融溶剂催化制备二酯类化合物

二酯类化合物广泛应用于有机中间体、药物、增塑剂、香料等领域,开发其绿色、高效的合成新方法具有重要意义.报道了以二元羧酸(或二羧酸酐)和脂肪醇为原料,以深共融溶剂(DESs)为催化剂催化合成二酯类化合物.以n(氯化胆碱):n(对甲苯磺酸)=1:2为催化剂,产率最高可达95％,并且DESs使用8次后产率仍保持在88％以上.运用1HNMR和13CNMR对产物进行了结构表征.该方法具有操作简单、产率高、易分离和催化剂可循环使用等优点.     

电磁脉冲辐射波模拟器双锥-平面线栅天线场分布规律

双锥-平面线栅结构的水平极化辐射波天线对辐射场半宽影响较小且架设方便、易于维护，掌握该型天线场分布规律是确定模拟器场均匀区、开展电磁脉冲效应实验的前提。利用天线理论研究双锥-平面线栅天线的场分布规律，结合数值模拟和实际天线试验对理论分析结果进行验证。结果表明：在天线结构和激励电压确定的条件下，双锥中心正下方辐射电场极化分量仅与测点到源的距离相关，二者呈反比；Oxz平面内以双锥中心为圆心的圆弧上任意一点辐射电场极化分量的幅值相等，并在同一时刻达到峰值；Oxz平面内同一水平线上的测点总辐射场幅值相等，方向沿测点所在圆弧的切线方向；各辐射场分量关于Oxz平面和Oyz平面对称分布；对于实际模拟器，地面反射会使辐射场波形下降沿陡降，导致地面附近辐射场半宽变小；线栅极板会影响附近的场分布，且极板外侧4个角点处的反射相对较强，其他位置辐射场分布与理论分析一致。     

Hydrogen sulfide gas detection by Au-decorated ZnO nanotube: a computational study and comparison to experimental observations

Based on the experimental reports, Au-decoration on the ZnO nanostructures dramatically increases the electronic sensitivity to H₂S gas. In the current study, we computationally scrutinized the mechanism of Au-decoration on a ZnO nanotube (ZON) and the influence on its sensing behavior toward H₂S gas. The intrinsic ZON weakly interacted with the H₂S gas with an adsorption energy of ?11.2 kcal/mol. The interaction showed no effect on the HOMO–LUMO gap and conductivity of ZON. The predicted response of intrinsic ZON toward H₂S gas is 6.3, which increases to 78.1 by the Au-decoration at 298 K. The corresponding experimental values are about 5.0 and 80.0, indicating excellent agreement with our findings. We showed that the Au atom catalyzes the reaction 3O₂?+?2H₂S?→?2SO₂?+?2H₂O. Our calculated energy barrier (at 298 K) is about 12.3 kcal/mol for this reaction. The gap and electrical conductance Au-ZON largely changed by this reaction are attributed to the electron donation and back-donation processes. The obtained recovery time is about 1.35 ms for desorption of generated gases from the surface of the Au-ZON sensor.     

变压器内部故障在线检测方法仿真及误差分析

为研究变压器内部故障在线检测方法的有效性及抗干扰性,搭建实际变压器的非线性三维有限元模型.对变压器常见几种类型的内部故障进行详细的结构仿真,通过"场-路耦合法"构建各类型故障的ΔV-I1轨迹.同时,通过对正常绕组的测量信号设置一定的误差,构建了考虑测量误差时的误差轨迹.在此基础上,将正常时的标准轨迹、误差轨迹和各种类型的故障轨迹进行对比分析,通过对ΔV-I1轨迹特征差异的定性分析与定量计算,验证该方法在实际应用中的有效性,总结判断各类型故障的规则,同时针对测量误差所造成的干扰提出了建议.     

爆炸冲击波载荷下预制孔铝板的动态响应

为研究爆炸冲击波对破片穿孔后板结构的毁伤效应,使用激波管为冲击波加载设备,对不同孔形的预制孔铝板进行冲击波加载.利用三维数字图像相关(3 D-DIC)技术,分析固支预制孔方形铝板在冲击波加载条件下的动态响应,得到预制孔铝板的动态响应和变形失效过程.结合3 D-DIC结果分析孔形对靶板刚度、破坏形式、承载能力的影响.结果表明:圆形孔靶板刚度最大,圆形孔靶板的极限承载能力最大,菱形孔靶板极限承载能力最差;孔形对撕裂破坏的影响主要体现在孔的角点在靶板分布上.该实验结果对固支板结构的抗爆设计具有一定参考价值.     

Corrosion behaviour of Mg-Gd-Y-Zn-Ag alloy components with different sizes after cooling

The corrosion behaviour of Mg-6Gd-3Y-1Zn-0.3Ag (wt.%) alloy components with different sizes after cooling was investigated. The alloys in the small components (SC) cooled fast, which were composed of α-Mg matrix and coarse long-period stacking ordered (LPSO) phases. The alloys in the large components (LC) cooled slowly, and there were thin lamellar LPSO phases precipitating inside the grains, except for α-Mg matrix and coarse LPSO phases. The hydrogen evolution test revealed that the corrosion rate of LC sample was higher than that of SC sample. Electrochemical impedance spectroscopy (EIS) test showed that the surface film on LC alloys provided worse protection. The corrosion morphologies indicated that the precipitation of the thin lamellar LPSO phases in LC sample caused severe micro-galvanic corrosion, which accelerated the rupture of the surface film.