整体壁板离散填料滚弯成形有限元模拟

具有一定曲率外形的铝合金整体壁板属于典型的多筋零部件,传统弯曲成形工艺成形困难,容易产生多种缺陷。提出了离散填料辅助滚弯成形整体2A12T4铝合金壁板滚弯工艺,并通过实验与整体填料滚变成形进行了对比,同时采用有限元模拟技术,探究了离散填料辅助整体壁板滚弯成形中的影响因素。研究结果表明:填料数量、上下垫板厚度等因素对成形性能影响较大,填料在3~6块时成形稳定,可以有效地避免筋条屈曲与失稳;随垫板厚度增加,壁板表面圆弧更加光滑、连续,但是回弹性增强;上下垫板分别在10~20 mm厚度时,综合性能较好。通过离散填料辅助滚弯技术可以成形出质量较高的整体壁板。     

Measurements of thermal-neutron capture cross-section of Cesium-135 by applying mass spectrometry

ABSTRACT

The thermal-neutron capture cross-section (σ₀) and resonance integral (I₀) were measured for the ¹³⁵Cs(n,γ)¹³⁶Cs reaction by an activation method and mass spectrometry. Because of difficulty in the preparation of pure ¹³⁵Cs samples, we used ¹³⁵Cs contained as an impurity in a normally available ¹³⁷Cs standard solution. An isotope ratio of ¹³⁵Cs and ¹³⁷Cs in a standard ¹³⁷Cs solution was measured by mass spectrometry to quantify ¹³⁵Cs. Cesium-135 impurity along with the ¹³⁷Cs standard solution was irradiated at the hydraulic conveyer of the research reactor in the Institute for Integral Radiation and Nuclear Science, Kyoto University. Wires of Co/Al and Au/Al alloys were used as neutron monitors to measure thermal-neutron fluxes and epi-thermal Westcott’s indices at an irradiation position. A gadolinium filter was used to measure the σ₀, and a value of 0.133 eV was taken as the cut-off energy. Gamma-ray spectroscopy was used to measure induced activities of ¹³⁷Cs, ¹³⁶Cs and monitor wires. On the basis of Westcott’s convention, the σ₀ and I₀ values were derived as 8.57 ± 0.25 barn, and 45.3 ± 3.2 barn, respectively. The value of σ₀ obtained in the present study agreed within the limits of uncertainties with the past-reported value of 8.3 ± 0.3 barn.     

Stress intensity factor evaluations for a curved crack in orthotropic particulate composites using an interaction integral method

This paper develops a domain-independent interaction integral (DII-integral) for extracting mixed-mode stress intensity factors (SIFs) for orthotropic materials with complex interfaces. The DII-integral does not require material property gradients, and moreover its validity is not affected by material interfaces. Combined with the extended finite element method (XFEM), the DII-integral is employed to investigate a straight crack in an orthotropic functionally graded plate and a curved crack in orthotropic particulate composites.     

基于滑模的二阶多智能体快速抗扰一致性

针对带有外部未知扰动的二阶多智能体系统的领导—跟随有限时间一致性问题，本文设计出一种带有时变增益的有限时间干扰观测器，用以实现对每个跟随智能体中未知扰动的快速估计，在此基础上，本文结合超螺旋积分滑模控制方法并利用邻居智能体的位置和速度信息设计一种快速抗扰一致性协议，该协议能够保证存在非线性动态的多智能体系统有限时间一致性控制并能抑制抖振现象.同时，利用李亚普诺夫函数进行了稳定性的证明.最后，通过Matlab数值仿真进一步验证了所提出协议的可行性.     

定向长钻孔整体水力压裂增透技术在赵固二矿的应用

针对赵固二矿煤层透气性低、钻孔有效影响半径小，实施定向长钻孔代替底板岩巷进行区域瓦斯治理期间钻孔工程量大、瓦斯抽采效果不理想的问题。结合煤层赋存特征及钻孔施工情况，采用定向长钻孔整体水力压裂增透技术，理论分析了合理坐封位置、压裂参数，完成200 m煤巷条带一次整体压裂，最大泵注压力24.3 MPa、累计注水量1 613 m³。并基于煤层全水分变化，考察确定了单个钻孔压裂影响范围达到巷道两帮30 m，有效改善了煤体储层特性，提高了煤层瓦斯抽采效率。在实现定向钻孔对预抽煤巷条带可靠控制的同时，最大程度降低了钻孔工程量、缩短了瓦斯治理周期，为实现矿区“以孔代巷”及高效安全开采提供了技术支撑。     

煤矿科室工作信息管理系统设计

为了提高了煤矿工作者的工作效率和矿井安全程度，设计了煤矿科室工作信息管理系统，分析了系统的关键技术，主要为J2EE技术和B/S和C/S的体系结构；根据现场调研，对系统需求进行了分析，然后设计了系统总体架构和系统功能模块。煤矿科室工作信息管理系统的应用，减少了人力资源的浪费，确保了信息的保存和查询的安全性。     

Mode-dependent stochastic stability criteria of fuzzy Markovian jumping neural networks with mixed delays

This paper investigates the stochastic stability of fuzzy Markovian jumping neural networks with mixed delays in mean square. The mixed delays include time-varying delay and continuously distributed delay. By using the Lyapunov functional method, Jensen integral inequality, the generalized Jensen integral inequality, linear convex combination technique and the free-weight matrix method, several novel sufficient conditions are derived to ensure the global asymptotic stability of the equilibrium point of the considered networks in mean square. The proposed results, which do not require the differentiability of the activation functions, can be easily checked via Matlab software. Finally, two numerical examples are given to demonstrate the effectiveness and less conservativeness of our theoretical results over existing literature.     

A novel quasi-oppositional harmony search algorithm and fuzzy logic controller for frequency stabilization of an isolated hybrid power system

The intermittent wind power in isolated hybrid distributed generation (IHDG) may cause serious problems associated with frequency (f) and power (P) fluctuation. Energy storage devices such as battery, super capacitor, and superconducting magnetic energy storage (SMES) may be used to reduce these fluctuations associated with f and P. This paper presents a study of IHDG power system for improving both f and P deviation profiles with the help of SMES. The studied IHDG power system is consisted of wind turbine generator and diesel engine generator. Both f and P control problems of the studied power system model are addressed in presence or absence of SMES. Fuzzy logic based proportional–integral–derivative (PID) controller with SMES is used for the purpose of minimization of f and P deviations. The different tunable parameters of the PID controller and those of the SMES are tuned by a novel quasi-oppositional harmony search algorithm. Performance study of the IHDG power system model is carried out under different perturbation conditions. The results demonstrate minimum f and P deviations may be achieved by using the proposed fuzzy logic based PID controller along with SMES.     

Solution for the general integral‐type nonlocal plasticity model with Tikhonov regularization

A new solution approach, based on Tikhonov regularization on the Fredholm integral equations of the first kind, is proposed to find the approximate solutions of the strain softening problems. In this approach, the consistency condition is regularized with the Tikhonov stabilizers along with a regularization parameter, and the internal variable increments are solved from the resulting Euler's equations. It is shown that, as the regularization parameter is increased, the solutions converge to a unique one. A nonlocal yield condition and a nonlocal return mapping algorithm are proposed to carry out the integration of constitutive equations in the time and spatial domains. A global plastic dissipation principle is proposed to relax the classical local plastic dissipation postulate. Numerical examples show that the proposed approach leads to objective, mesh‐independent solutions of the softening‐induced localization problems. A comparison of the results from the proposed approach with those from the gradient‐dependent plasticity model shows that the two models give close solutions.     

双磁极式磁粒研磨机理分析及试验研究

目的解决平面磁粒研磨中压力不均匀和需要反复调整研磨间隙的问题,设计双磁极式研磨方法。方法首先对双磁极式研磨方法机理进行分析,并对研磨区域单颗磨粒进行受力分析,寻找影响研磨压力的主要因素;其次利用Ansoft Maxwell软件对两种研磨方法进行磁场仿真,分析两种研磨方法的研磨区域磁场梯度变化,通过面积积分法对比磁感应强度的影响程度;最后设计试验装置,通过试验对理论分析及有限元分析的结果进行验证,对比研磨前后工件表面粗糙度及微观形貌变化。结果双磁极式研磨方法中磨粒的研磨压力完全由磁场力提供,与研磨区域磁感应强度成正比,研磨区域磁感应强度比"铣削式"研磨方法提高约34.56%。两种方法在相同试验条件下对SUS304不锈钢板研磨40 min,双磁极式研磨方法研磨后,工件表面原始纹理基本被去除,表面粗糙度值由原始的0.25μm下降至0.16μm,下降率为36%,比"铣削式"研磨方法提高约80%,粗糙度曲线波动平缓,波峰波谷高度差变化均匀且表面形貌光滑平整。结论双磁极式研磨方法研磨区域磁场梯度变化明显,利于磨粒流动更新,研磨压力相对稳定,表面粗糙度下降率高,研磨后工件表面形貌光整,与"铣削式"研磨方法相比具有较明显的优势。