Dual functions of three-dimensional hierarchical architecture on improving the rate capability and cycle performance of LiNi0.8Co0.1Mn0.1O2 cathode material for lithium-ion battery

The main obstacles in lithium-ion battery are limited by rate performance and the rapid capacity fading of LiNi_0.8Co_0.1Mn_0.1O₂ (NCM811). Herein, a novel three-dimensional (3D) hierarchical coating material has been fabricated by in situ growing carbon nanotubes (CNTs) on the surfaces of Ni–Al double oxide (Ni–Al-LDO) sheets (named as LDO&CNT) with Ni–Al double hydroxide (Ni–Al-LDH) as both the substrate and catalyst precursor. The resultant LDO&CNT nanocomposites are uniformly coated on the surfaces of NCM811 by the physical mixing method. The rate capability of the resultant cathode material retains to 78.80% at a current rate of 3C. Its capacity retention increases by 6.7–14.42% compared with pristine NCM811 after 100 cycles within a potential range of 2.75–4.3 V at 0.5C. The improved rate capability and cycle performance of NCM811 are assigned to the synergistic effects between Ni–Al-LDO and CNTs. The hierarchical LDO&CNT nanocomposites coating on the surface of NCM811 avoids the aggregation of conductive CNTs and the stacking of Ni–Al-LDO nanosheets. Furthermore, it accelerates Li⁺ and electrons shuttle and reduces the reaction of Li₂O with H₂O and CO₂ in air, which results in Li₂CO₃ and LiOH alkali formation on the NCM811 surface.     

Interfacial microstructure and mechanical properties of Ti3SiC2 ceramic and TC11 alloy joint diffusion bonded with a Cu interlayer

Reliable joints of Ti₃SiC₂ ceramic and TC11 alloy were diffusion bonded with a 50 μm thick Cu interlayer. The typical interfacial structure of the diffusion boned joint, which was dependent on the interdiffusion and chemical reactions between Al, Si and Ti atoms from the base materials and Cu interlayer, was TC11/α-Ti + β-Ti + Ti₂Cu + TiCu/Ti₅Si₄ + TiSiCu/Cu(s, s)/Ti₃SiC₂. The influence of bonding temperature and time on the interfacial structure and mechanical properties of Ti₃SiC₂/Cu/TC11 joint was analyzed. With the increase of bonding temperature and time, the joint shear strength was gradually increased due to enhanced atomic diffusion. However, the thickness of Ti₅Si₄ and TiSiCu layers with high microhardness increased for a long holding time, resulting in the reduction of bonding strength. The maximum shear strength of 251 ± 6 MPa was obtained for the joint diffusion bonded at 850 °C for 60 min, and fracture primarily occurred at the diffusion layer adjacent to the Ti₃SiC₂ substrate. This work provided an economical and convenient solution for broadening the engineering application of Ti₃SiC₂ ceramic.     

Study of Pb-based and Pb-free perovskite solar cells using Cu-doped Ni1-xO thin films as hole transport material

SCAPS solar cell simulation program was applied to model an inverted structure of perovskite solar cells using Cu-doped Ni_1-xO thin films as hole transport layer. The Cu-doped Ni_1-xO film were made by co-sputtering deposition under different deposition conditions. By increasing the amount of the Cu-dopant, the film crystallinity enhanced whereas the bandgap energy decreased. The transmittance of the thin films decreased significantly by increasing the sputtering power of copper. High quality, uniform, compact, and pin-hole free films with low surface roughness were achieved. The structural, chemical, surface morphology, optical, electrical, and electronic properties of the Cu doped Ni_1-xO films were used as input parameters in the simulation of Pb-based (MAPbI_3-xCl_x) and Pb-free (MAGeI₃) perovskite solar cells. Simulation results showed that the performance of both Pb-based and Pb-free perovskite solar cell devices significantly enhanced with Cu-doped Ni_1-xO film. The highest power conversion efficiency (PCE) for the Pb-free perovskite solar cell is 8.9% which is lower than the highest PCE of 17.5% for the Pb-based perovskite solar cell.     

Microstructures and properties of nickel-titanium carbide composites fabricated by laser cladding

In this work, Ni/TiC composites were synthesized by the laser cladding technique (LCT). A scanning electron microscope (SEM), X-ray diffractometer (XRD), microhardness meter, electrochemical workstation, and friction and wear tester examined the microstructure, surface morphology, phase structure, microhardness, wear, and corrosion resistances of the Ni/TiC composites. These results indicated the Ni/40TiC composite contained finer equiaxed crystals than the Ni and Ni/20TiC composites. In addition, numerous TiC particles in the Ni/40TiC composite impeded growth of the nickel crystals, which resulted in the fine microstructure of the Ni/40TiC composite. The Ni, Ni/20TiC, and Ni/40TiC composites exhibited face-centered cubic (f c c) lattices. The average microhardness values of the Ni/20TiC and Ni/40TiC composites were approximately 748 HV and 851 HV, respectively. The Ni/40TiC composite had the lowest friction coefficient (0.43) among all three coatings, and only some shallow scratches appeared on the surface of the Ni/40TiC composite. The corrosion potential (E) of Ni/40TiC exceeded the Ni/20TiC composite, and both were larger than the Ni composite, which indicated the Ni/40TiC composite had outstanding corrosion resistance and the Ni composite had poor corrosion resistance. The corrosion current densities (i) of Ni, Ni/20TiC, and Ni/40TiC composites were 5.912, 4.405, and 3.248 μA/cm², respectively.     

Effect of impact angle on wear behavior of Mo2NiB2–Ni cermets with different Ni content

Herein, the influence of the impact angle and Ni content on the wear behavior of Mo₂NiB₂–Ni cermets was studied using an erodent-carrying slurry comprising artificial seawater and SiO₂ sands. The results reveal that the material loss may be attributed to the wear damage caused by SiO₂ sands because cermets are expected to exhibit good corrosion resistance in artificial seawater. The relative density of cermets markedly influences their resistance to wear damage, and the material loss experienced by cermets with poor relative density is 2–4 times higher than that of cermets with good relative density; this occurs because a higher relative density can markedly enhance the mechanical properties and reduce the defects in the cermets. Moreover, the results indicate that as the impact angle increases from 0° to 60°, the manifestation of the wear mechanism changes from damaging the Ni binder phase (caused by single cutting wear) to damaging both the Mo₂NiB₂ ceramic and Ni binder phases due to the combination of cutting wear and impact wear. The wear damage is dominated by the cutting wear and impact wear from SiO₂ sand at the low and high impact angles, respectively. Furthermore, the severe deterioration of the single ceramic skeleton at high impact angles indicates that the synergistic influence of the Mo₂NiB₂ ceramic and Ni binder phases on enhancing the wear resistance of the cermets intensifies at high impact angles.     

Fabrication of 3D Ni nanosheet array on Crofer22APU interconnect and NiO-YSZ anode support to sinter with small-size Ag nanoparticles for low-temperature sealing SOFCs

A novel low-temperature sealing method was developed to seal solid oxide fuel cells. The 3D Ni nanosheet array was pre-fabricated on faying surfaces of Crofer22APU interconnect and NiO-YSZ anode-support. Then it was covered with Au film without changing its morphology. This special nanostructure improved sintering efficiency between Ag nanoparticles and substrates. A dense joint was obtained at the low-temperature between 250 °C–300 °C. This method effectively avoided the oxidation of interconnect during sealing. When joints were sealed at 300 °C, the shear strength reached 16 MPa. The fracture was mainly located in the central Ag layer, presenting a significant plastic deformation. Due to the effective protection of Ni layer, joints also possessed excellent oxidation resistance in oxidizing atmosphere at 800 °C for 400 h. After high-temperature oxidation, the shear strength was increased to 23 MPa, revealing an increasement of 43.8% compared with the as-sealed condition (16 MPa). This sealing method has great potential in sealing solid oxide fuel cells. It also can be extended to seal other energy-conversion devices.     

Joining of dense Si3N4 ceramics with tape cast Lu-Al-Si-O-N interlayer

Lu-Al-Si-O-N tapes with different thickness were used to join gas pressure sintered Si₃N₄ ceramics. The microstructure of the joints and the influences of the joint thickness and joining temperature on the bonding strength of the as-joined Si₃N₄ ceramics have been investigated. The highest bonding strength about ~ 300 MPa of the joined specimens was achieved by using 450 µm interlayer at 1450 °C. The existence of Si₃N₄ nanowires was beneficial for the improvement of the bonding strength by interweaving the oxynitride glass matrix in the joint region.     

Developing high-performance laminated Cu/TiC composites through melt infiltration of Ni-doped freeze-cast preforms

Nacre-inspired laminated composites have been proven to possess a unique combination of strength and toughness. In this study, we fabricated nacre-mimetic Cu/TiC composites via unidirectional freezing of aqueous TiC slurries containing different amounts of NiO additives, followed by ice sublimation, carbothermal reduction of NiO to Ni during sintering and then gas-pressure infiltration of the Cu melt. The introduction of Ni greatly facilitated the densification of ceramic lamellae and enhanced the interfacial bonding between Cu and TiC. The resultant composites displayed outstanding damage tolerance and anisotropic electrical conductivities. Specifically, for an ～31?vol% TiC–Cu composite containing 24?wt% Ni in the ceramic lamellae (based on the TiC content), a fracture toughness (K_Jc) of 72.5?±?1.0?MPa·m^1/2, work of fracture of 53.4?±?3.5?kJ/m², bending strength of 725?±?11?MPa and longitudinal electrical conductivity of 22.7?MS/m (～60% of the Cu matrix) were achieved, which were approx. 81%, 536%, 122% and 97% higher than those of the Ni-free composite, respectively. Noticeable toughening was demonstrated to be a consequence of multiple cracking, plastic deformation and uncracked-ligament bridging of the metal layers, as well as crack deflection and blunting. On the other hand, significant strengthening resulted from tailoring the microstructures in the ceramic layers and at the Cu/TiC interface as a result of Ni doping. We believe that the facile strategy adopted herein provides an effective way to solve the problems of wetting and bonding related to metal infiltration and can be readily extended to the preparation of other nacre-inspired metal?ceramic composites.     

Structural Aspects of P2-Type Na0.67Mn0.6Ni0.2Li0.2O2 (MNL) Stabilization by Lithium Defects as a Cathode Material for Sodium-Ion Batteries

A known strategy for improving the properties of layered oxide electrodes in sodium-ion batteries is the partial substitution of transition metals by Li. Herein, the role of Li as a defect and its impact on sodium storage in P2-Na_0.67Mn_0.6Ni_0.2Li_0.2O₂ is discussed. In tandem with electrochemical studies, the electronic and atomic structure are studied using solid-state NMR, operando XRD, and density functional theory (DFT). For the as-synthesized material, Li is located in comparable amounts within the sodium and the transition metal oxide (TMO) layers. Desodiation leads to a redistribution of Li ions within the crystal lattice. During charging, Li ions from the Na layer first migrate to the TMO layer before reversing their course at low Na contents. There is little change in the lattice parameters during charging/discharging, indicating stabilization of the P2 structure. This leads to a solid-solution type storage mechanism (sloping voltage profile) and hence excellent cycle life with a capacity of 110 mAh g^-1 after 100 cycles. In contrast, the Li-free compositions Na_0.67Mn_0.6Ni_0.4O₂ and Na_0.67Mn_0.8Ni_0.2O₂ show phase transitions and a stair-case voltage profile. The capacity is found to originate from mainly Ni³⁺/Ni⁴⁺ and O^2-/O^2-δ redox processes by DFT, although a small contribution from Mn⁴⁺/Mn⁵⁺ to the capacity cannot be excluded.