煤矿水仓清理新工艺

通过调研现场情况以及检测煤泥特性，探寻一种实用性强、方法简单的新工艺来替代劳累的人工和繁琐的机械清淤，解决现实问题。针对实际情况开发清仓新工艺，介绍了该工艺的技术路线选择、设计依据以及实际应用效果。该新工艺具有降低清仓时间、减轻工人劳动强度、设备操作简单、实用性强等特点。     

“方变圆”变径筒状结构滑模施工技术

为解决塔式光热的核心构筑物吸热塔"方变圆"变径超高筒体结构施工难题,选用一套可变形的滑模平台系统,通过操作系统上可调千斤顶支座、门架横向液压千斤顶装置、多处可调节模板角度和收缩模板的丝杆等,使得滑模根据施工需求可在一定的范围内调节模板倾角、间距,并逐步完成收缩变形,其理论滑模允许偏角20°,最终高效完成异形结构施工。该滑模系统刚度大、承载及堆料能力强、空间大、机械化程度高,施工操作简单,安全性高,适应沙漠极端环境。全过程仅需使用一套滑模体系,就能完成方形段、方变圆的变形段及圆形段施工,大大提高了施工效率,为类似环境下相似结构的施工提供了一定的参考。     

Three distinct optical-switching states in phase-change materials containing impurities:From physical origin to material design

Ge2Sb2Tes is the most widely utilized chalcogenide phase-change material for non-volatile photonic applications,which undergoes amorphous-cubic and cubic-hexagonal phase transition under external excitations.However,the cubic-hexagonal optical contrast is negligible,only the amorphous-cubic phase transition of Ge2Sb2Te5 is available.This limits the optical switching states of traditional active dis-plays and absorbers to two.We find that increasing structural disorder difference of cubic-hexagonal can increase optical contrast close to the level of amorphous-cubic.Therefore,an amorphous-cubic-hexagonal phase transition with high optical contrast is realized.Using this phase transition,we have developed display and absorber with three distinct switching states,improving the switching perfor-mance by 50％.Through the combination of first-principle calculations and experiments,we reveal that the key to increasing structural disorder difference of amorphous,cubic and hexagonal phases is to intro-duce small interstitial impurities(like N)in Ge2Sb2Tes,rather than large substitutional impurities(like Ag)previously thought.This is explained by the formation energy and lattice distortion.Based on the impurity atomic radius,interstitial site radius and formation energy,C and B are also potential suit-able impurities.In addition,introducing interstitial impurities into phase-change materials with van der Waals gaps in stable phase such as GeSb4Te7,GeSb2Te4,Ge3Sb2Te6,Sb2Te3 will produce high optical con-trast amorphous-metastable-stable phase transition.This research not only reveals the important role of interstitial impurities in increasing the optical contrast between metastable-stable phases,but also proposes varieties of candidate matrices and impurities.This provides new phase-change materials and design methods for non-volatile optical devices with multi-switching states.     

车用有机朗肯循环系统中计量泵的性能研究

在模拟车用有机朗肯循环(organic Rankine cycle,ORC)系统的工作环境下,设计并搭建以R123作为工质的液压隔膜计量泵性能测试平台。在额定转速(2900 r/min)下,通过调节液压隔膜计量泵的冲程(25%、50%、75%、100%)和出口压力,得到变工况下液压隔膜计量泵的特性曲线,并分析液压隔膜计量泵的关键参数对车用ORC系统性能的影响情况。结果表明:液压隔膜计量泵的流量受冲程影响,与出口压力基本无关。其输入功率和实际运行效率均随着冲程的增加而升高,最高分别可达523.91 W、88.27%。应用该液压隔膜计量泵的模拟车用ORC系统吸热量变化范围较广,系统热效率最高可达12.81%。液压隔膜计量泵可应用于车用ORC系统,通过调节液压隔膜计量泵的冲程和出口压力,可实现提高车用ORC系统热效率、增加系统净输出功率的目的。     

汽蚀对离心泵性能影响的实验研究

离心泵长时间运转后,会出现危害严重的汽蚀现象,造成泵性能下降,严重时影响泵的效率、寿命,甚至造成离心泵内部部件损坏。文章通过改变进口压力的方法对单泵、双泵并联、双泵串联等工况下汽蚀对离心泵性能影响进行实验研究。结果表明:当进口压力小于输送液体的饱和蒸汽压时,液体开始发生气化并伴随气泡产生,表明泵内发生汽蚀;汽蚀初期离心泵的效率开始下降,但表现不明显;随着汽蚀不断增大至严重汽蚀区时,Q 1~η曲线出现陡坡,效率出现明显下降并伴随嗡响。实验证明采用提高泵的进口压力等措施可适当减小汽蚀对泵性能的不利影响。     

煤层顶板硬岩大直径定向钻孔施工关键技术

根据顶板高位定向钻孔快速钻进成孔与工作面卸压瓦斯高效抽采治理需要，针对现有螺杆马达定向钻进技术与分级扩孔方法存在的问题，开展了顶板硬岩定向钻进与大直径扩孔钻进关键技术研究，开发了冲击回转定向钻进技术、扭冲回转定向钻进技术、扭冲旋转扩孔技术以及双级双速扩孔技术等钻孔提速新技术，研制了冲击螺杆马达、矿用小直径扭力冲击器、双级双速螺杆马达、组合式扩孔钻头等配套钻具。综合试验结果表明，硬岩定向钻孔平均机械钻进效率达到8.34 m/h，最高达到13.6 m/h，较常规螺杆马达定向钻进技术提升20%~30%；硬岩大直径扩孔终孔直径达到200 mm，机械钻进效率平均达到5.6 m/h以上，最高达到10.5 m/h。该技术提升了顶板硬岩定向钻进效率与大直径扩孔钻进效率，缩短了顶板高位定向钻孔的综合施工周期，为大直径高位定向长钻孔快速成孔与高效抽采治理回采工作面卸压瓦斯提供了可靠的技术手段。     

水泵水轮机导叶动态水力矩特性分析

采用SST k-ω湍流模型对某高水头水泵水轮机进行全流道三维非定常数值模拟,分别对在水轮机工况和水泵工况运行下的导叶动态力矩特性进行分析。结果表明:在水轮机工况下,随着流量的增大,不同位置处导叶的动态水力矩变化规律一致,力矩值由正值变为负值,力矩脉动频率与转轮叶片数相关,流量越大,叶频影响越显著;在水泵工况下,最高扬程工况时导叶水力矩脉动频率主频为转频且脉动幅值较大,而最低扬程工况下导叶水力矩脉动主频为叶频,力矩脉动幅值较小。     

甲基氯硅烷精馏流程的模拟与优化

采用Aspen plus软件对工业七塔精馏过程进行全流程建模与模拟，优化工艺参数，研究了新的精馏节能工艺。对一甲塔等7个精馏塔采用双因素水平的灵敏度分析，考察了塔釜采出率、回流比、进料位置和塔顶压力对产品浓度和热负荷的影响，确定一甲塔最优的工艺参数：塔釜摩尔采出率为0.92，摩尔回流比为130，塔顶压力为0.18 MPa，总理论板数为400，在210块理论板位置进料。在此基础上，针对高能耗的脱高塔/脱低塔，模拟研究了双效精馏新工艺，新工艺可节省39.70%的年总成本；针对一甲塔模拟研究了热泵精馏新工艺，新工艺可降低41.42%的年总成本。     

Common Mode Voltage Reduction Using 3D-SVPWM for 3-level CI-NPC Inverter with Hybrid Energy System

This paper elucidates Common Mode Voltage (CMV) reduction in transformerless 3-phase 3-level Coupled Inductor Neutral Point (CI-NPC) Clamped Inverter with Hybrid Energy System. The three dimensional Space Vector Pulse Width Modulation (3D-SVPWM) with Nearest State Vector (NSV) is implemented to reduce the CMV by proper selection of medium, large and small vectors in 3D cubic space region. This NSV scheme in addition to CMV reduction, reduces the capacitor voltage balancing issues and minimizes switching losses. The proposed control provides full utilization of dc link voltage with reduced harmonics. This 3-level CI-NPC inverter is energized by hybrid energy source which includes photovoltaic system and wind energy system. The results obtained for the proposed scheme through simulation and experimental setup is compared with the conventional 2D-SVPWM and 3D-SVPWM scheme. From the compared results it is evident that the proposed scheme reduces CMV to a larger extent than 2D and 3D-SVPWM control. The simulation and experimental results are verified using matlab-simulink and FPGA-Spartan-6 controller respectively.     

库水位变动下庄屋滑坡变形与稳定性分析

库水位变动是三峡库区滑坡等地质灾害频发的重要原因之一。为研究库水位变动对库岸涉水滑坡变形和稳定性的影响,以庄屋滑坡为例,结合GPS位移监测数据和数值模拟分析,探讨了该滑坡在库水升降过程中变形和稳定性的响应规律。结果表明,庄屋滑坡受库水影响滑坡后缘变形大于前缘,为推移式滑坡。水位变动过程中,滑坡渗流和稳定性变化具有动水压力型滑坡特点,即在水位上升时滑体内地下水浸润线呈内凹趋势,水位下降时滑体内地下水浸润线呈外凸趋势,且具有一定的滞后性;库水位上升时滑坡稳定性系数增大,水位下降时减小;当库水位保持在恒定水位时,稳定性系数也逐渐趋于稳定。