纳米级超声造影剂的理论研究进展

为了克服超声造影剂中微米级气泡尺寸较大的局限性,大量研究人员对超声应用的替代造影剂(纳米级造影剂)进行了研究。随着生物纳米技术的飞速发展,纳米级超声造影剂在诊断与治疗领域有着广阔的发展前景。与超声造影剂中的微米级气泡相比,纳米级造影剂粒径较小,渗透能力极强,可以通过血管内皮间隙,进而可以实现血管外病变部位的显影。文中详细论述了超声造影剂在超声作用下的行为以及2种主要的纳米级造影剂:纳米气泡和纳米液滴造影剂,对其理论研究进展进行了总结,并提出了目前仍存在的一些问题及其未来的研究方向。     

Hydrodynamics study of a fast liquid–liquid oxidation process with in situ gas production in microreactors

Hydrodynamics characteristics of a fast and highly exothermic liquid–liquid oxidation process with in situ gas production in microreactors were studied using a newly developed experimental method. In the adipic acid synthesis through the K/A oil (the mixture of cyclohexanol and cyclohexanone) oxidation with nitric acid, bubble generation modes were divided into four categories. The gas production became more intensive, unstable, even explosive with increasing the oil phase feed rate and the temperature. A novel automatic image processing method was developed to monitor the instantaneous velocity online by tracking the gas–liquid interface. The axial velocity at the same location was unstable due to the changing gas production rate. Furthermore, the actual residence time was obtained easily with being only 36% of the space–time minimally, beneficial for establishing accurate kinetics and mass transfer models with time participation. Finally, an empirical correlation was developed to predict the actual residence time under different conditions.     

Taylor Bubble Study of the Influence of Fluid Dynamics on Yield and Selectivity in Fast Gas-Liquid Reactions

A consecutive competitive gas-liquid reaction is investigated using a Taylor bubble setup regarding the influence of fluid mixing in the bubble wake on yield and selectivity. The concentration fields behind a Taylor bubble are visualized and measured quantitatively with a novel time-resolved absorption imaging technique based on Beer Lamberts law and an integral selectivity is derived. In addition, the calculation of the local selectivity, often used in numerical approaches, is discussed and the existing experimental limits for its derivation are pointed out. Finally, an increase in selectivity of a competitive consecutive reaction for enhanced mixing is experimentally confirmed.     

水力空化改质对重质原油沥青质及性质的影响

利用水力空化过程产生局部的高温、高压、高射流以及强大的剪切力等极端化学物理条件改质处理沙特重质原油，试验结果表明：沙特重质原油经过水力空化改质后粘度由13.61降低至7.22mm2/s，残碳由7.16%降低至6.48%，实沸点蒸馏后减压渣油降低1个百分点。进一步采用APPI FT-IR MS、XRD、FT-IR、SEM和粒度分布等技术研究了水力空化改质对沙重原油分子组成，沥青质团聚体微晶结构、沥青质胶束粒径分布、沥青质官能团、沥青质形貌等方面的影响，从分子角度阐述空化改质重油的机理。研究结果表明：水力空化改质后沙重原油分子量分布、芳烃类化合物缔合作用变小；沥青质对低DBE化合物吸附性能降低；沥青质团聚体微晶结构更加松散；沥青质胶束粒度分布降低；沥青质分子相互团聚作用力减弱。进一步考察了水力空化改质前后减压渣油延迟焦化性能，改质处理后焦炭产率降低1.85个百分点，液体收率和气体产率分别增加1.52和0.33个百分点，水力空化改质对沥青质性质、结构特点的改善能够有效的提高其加工性能。     

Formation process of zirconia nanotubes and porous structures and model of oxygen bubble growth

Preparation and growth mechanism of anodization of Ti and Al has been widely concerned for two decades, but the research on anodic ZrO₂ is relatively lacking. In this paper, anodic TiO₂ and ZrO₂ nanotubes were prepared in glycerol electrolyte containing 0.35 M NH₄F and 4 vol% H₂O under different anodizing voltages. We had successfully prepared the anodic ZrO₂ nanotubes (AZNTs) with a complete top and a “bulb” at the bottom under 60 V, and with the increase of the applied anodizing voltage, the “bulb” cavity also increased. However, under the same anodizing conditions, the surface of anodic TiO₂ nanotubes (ATNTs) is a cluster of nano-tip morphology, and the bottom of the ATNTs is a conventional hemisphere shape. In addition, both AZNTs and porous anodic zirconia (PAZ) were found to coexist in the anodic ZrO₂ layer prepared at 60 V. Here, we used the oxygen bubble model and ionic current and electronic current theories to analyze the reason of the special morphology. It is confirmed that the porous anodic oxides are actually evolved from nanotubes. In other words, the structure is essentially the same.     

Simulation and exploration of cavitation process during microalgae oil extracting with ultrasonic-assisted for hydrogen production

Microalgae is promising to be used as feedstock resources for hydrogen production due to its high oil and grease contents. This promotes the development of extraction technology of microalgae oil. In this study, based on the Rayleigh-Plesset equation, the effects of temperature, pressure, ultrasonic power and frequency on the bubble motion of ethanol ultrasound cavitation are investigated. Subsequently, the effects of different process parameters on the extraction rate are studied using Schizochytrium sp. as raw material by stirring or ultrasonic-assisted extraction. And the composition of algae extraction oil is analyzed. The results show that the amplitude of cavitation bubbles increases with the increase of ultrasonic power and decrease of ultrasonic frequency. The extraction rate of algae oil reaches 93.76 ± 0.48% when the ultrasonic power is 150 W, the reaction time is 30 min, the temperature is 50 °C and the liquid-solid ratio is 10:1.     

Controlled galvanic decoration boosting catalysis: Enhanced glycerol electro-oxidation at Cu/Ni modified macroporous films

We report on glycerol electro-oxidation in alkaline medium at macroporous Ni electrodes decorated with Cu particles. Macroporous Ni film is electrodeposited, using hydrogen bubbles as dynamic templates, atop of a Cu substrate. This film shows good electrocatalytic activity towards glycerol oxidation reaction (GOR). The Ni film is further decorated with Cu via spontaneous deposition from CuSO₄ solution. This is done to enhance the catalytic activity of the film towards GOR. The morphology of the Cu-decorated Ni film is controlled using various additives such as KCl and (NH₄)₂SO₄ which are added to the Cu deposition bath. The as-prepared Cu-decorated Ni films are characterized by electrochemical measurements, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). It is found that these additives have tremendous effects on the morphology and the electrocatalytic activity of the decorating Cu particles.The decorated Ni foam showed superior electrocatalytic activity towards the GOR, as confirmed by the negative shift in the onset oxidation potential (ca. 100 mV) together with an increase in oxidation current that is up to 1.5-fold during the cyclic voltammetry (CV) measurements, compared to the undecorated Ni foam.     

上升气泡内气溶胶沉降机理研究

气溶胶池洗过滤是反应堆严重事故中去除放射性源项的重要手段。本文以严重事故条件下上升气泡中气溶胶的滞留过程为背景，设计搭建了可视化单气泡鼓泡实验装置。通过该装置研究了气溶胶在上升气泡中的沉降效率，并与MELCOR中的气溶胶沉降模型计算结果进行了对比。结果表明，气溶胶沉降效率对气泡尺寸的变化较为敏感，当气体流量大于0.1 L/min时，气泡等效直径迅速增加，相应的气溶胶沉降效率快速降低；与MELCOR模型计算结果的对比表明，两者在总体趋势上呈现出较好的一致性，但计算结果低估了液相对气溶胶的实际去除能力，导致这种偏差的主要原因是气泡在上升过程中存在无规则的晃动以及气液界面的波动。     

Numerical modeling of effect of slot on bubble motion in aluminum electrolytic process

A transient three-dimensional (3D) model was established to understand the bubble motion in an industrial electrolytic process. An anode with a new design was tested. It incorporates two slots that allow an efficient removal of gas bubbles. The electromagnetic fields were described by solving Maxwell's equations. The bubble movement was studied with two-way coupling Euler–Lagrange approach. The interplay of current density and bubble nucleation rate was included. The collision and coalescence of bubbles were considered. Random walk module was invoked for involving the chaotic effect of the turbulence. The numerical results were validated by experimental measurements. The results indicate that the current distribution and the bubble nucleation periodically change. Due to the slot, the bubble elimination heavily increases. The contribution of the slot to the bubble removal exceeds 50% in the case of three currents, and the promotion of the slot decays with increasing the current.     

阶梯溢流坝面坡度对一体化消能工水力特性的影响

为探求高水头、大单宽流量下坝面坡度对一体化消能工水力特性的影响,以阿海水电站为原型,采用三维k-ε双方程紊流模型,引入水气两相流VOF计算方法,利用几何重建格式来迭代生成自由水面,对1∶0.80、1∶0.75、1∶0.65三种阶梯面坡比进行数值模拟研究。结果表明:①最大负压值均位于首级阶梯立面凸角下1/4附近,并随坡度增加而增大。坡度为56.98°时,最大负压值为61.02 kPa,超过了6×9.81 kPa。②水流空化数在宽尾墩水舌出口位置出现最小值,空化数随坡度变陡而减小。坡度为56.98°时,空化数最小为0.358。坡度为51.34°时,空化数最大,为0.381。③随着阶梯溢流坝坝面坡度变缓,消力池最大临底流速增大。当坡度为51.34°时,消力池最大临底流速最大,达到26.84 m/s,超过了25 m/s,易发生冲磨破坏。当坡度为56.98°时,消力池最大临底流速最小,为24.00 m/s。消力池尾坎前最大临底流速随坡度增加而减小,坡度为56.98°时最小,为9.63 m/s;坡度为51.34°时,消力池尾坎前最大临底流速最大,为9.96 m/s。④坡度的变化对一体化消能工消能率的影响不大,坡度从51.34°增加到56.98°,消能率只提升0.15%。