空冷器用高压水清洗与雾化降温系统集成设计与开发

高压水清洗系统和喷淋降温系统分别是春季保持空冷器翅片表面清洁和夏季保证空冷器在高温下正常运行的2个重要辅助系统。针对喷淋系统的缺点研究了高压射流雾化技术,通过试验论证了高压水清洗与雾化降温系统集成的可行性和合理性。根据设计思路开发的集成系统已在山西某项目获得应用并取得了良好的使用效果,此高压水清洗与雾化降温集成系统中高压水发生装置及介质输送管路共用,产生的高压水射流雾化颗粒可达到60μm,夏季降温效果较传统喷淋降温效果大幅提升,水资源的利用率得到极大提高,系统性价比更高。     

Refinement of primary carbides in AISI DC 53 cold work tool steel by thin section copper permanent mould casting and water atomization

In this study, as alternative methods to conventional production methods involving thin section copper permanent mould casting (fast solidification) and water atomization (rapid solidification) of AISI DC 53 cold work tool steel have been investigated. Thin slabs obtained by copper mould casting was homogenized at 1150 °C for one hour and then hot rolling was be applied. After hot rolling, conventional heat treatment have been applied to thin slabs. The same heat treatment procedure have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. In order to investigate also the effect of rapid solidification on AISI DC 53 tool steel, steel powder was produced by water atomization technique. Experiments have revealed that thin steel slabs in permanent copper mould and rapidly solidified tool steel powder by water atomization have a more refined primary M₇C₃ carbides than commercially available steel.     

板栗壳黄酮结构分析及其对胰脂肪酶活力的抑制作用

在分析板栗壳黄酮结构的基础上，研究其对胰脂肪酶的抑制作用及类型。采用醇提法提取板栗壳中的黄酮，并用AB-8大孔吸附树脂进行纯化，冻干后得到的黄酮含量为（107.50±1.00）mg/g，提取得率为（5.66±0.05）%。利用超高效液相色谱-四极杆/静电场轨道阱质谱联用技术对板栗壳黄酮进行结构分析，鉴定出8 种黄酮类化合物。采用对硝基苯酚法测定胰脂肪酶活力，分别考察板栗壳黄酮对胰脂肪酶的抑制效果及不同反应条件下板栗壳黄酮对胰脂肪酶活性的影响，结果表明，板栗壳黄酮对胰脂肪酶有较好的抑制作用，半抑制浓度（half maximal inhibitory concentration，IC50）为0.074 mg/mL，且使胰脂肪酶最适pH值向碱性偏移。通过Lineweaver-Burk双倒数作图法确定其抑制类型为非竞争性抑制，抑制常数Ki＝53.19 mg/mL。由此可见，板栗壳黄酮是一种效果良好的胰脂肪酶抑制剂。     

Preparation and electrochemical characterization of Ti-based amorphous metallic glass with high strength

Ti-based amorphous metallic glasses have excellent mechanical, physical, and chemical properties, which is an important development direction and research hotspot of metal composite reinforcement. As a stable, simple, efficient, and large-scale preparation technology of metallic powders, the gas atomization process provides an effective way of preparing amorphous metallic glasses. In this study, the controllable fabrication of a Ti-based amorphous powder, with high efficiency, has been realized by using gas atomization. The scanning electron microscope, energy-dispersive spectrometer, and X-ray diffraction are used to analyze surface morphology, element distribution, and phase structure, respectively. A microhardness tester is used to measure the mechanical property. An electrochemical workstation is used to characterize corrosion behavior. The results show that as-prepared microparticles are more uniform and exhibit good amorphous characteristics. The mechanical test shows that the hardness of amorphous powder is significantly increased as compared with that before preparation, which has the prospect of being an important part of engineering reinforced materials. Further electrochemical measurement shows that the corrosion resistance of the as-prepared sample is also significantly improved. This study has laid a solid foundation for expanding applications of Ti-based metallic glasses, especially in heavy-duty and corrosive domains.     

流量脉动对燃油喷嘴雾化过程影响的实验研究

针对航空发动机燃烧室中存在的燃油流量脉动问题开展实验研究,设计并搭建了燃油喷嘴流量脉动激光可视化实验台,在等流量条件下利用高频激光粒子图像速度仪(High Speed Particle Image Velocimetry, PIV)分析燃油脉动频率变化对喷嘴雾化特性影响。实验结果表明:流量脉动促进了液膜表面的发展及液膜的破碎,对喷嘴的雾化产生积极的影响;喷嘴下游带状液膜区的发展和液滴的瞬态速度与喷嘴的流量脉动频率具有一致性;液滴的瞬态速度脉动幅值受脉动频率影响,在50 Hz时存在极大值。     

Mild hydrogen production from the hydrolysis of Al–Bi–Zn composite powder

The development of mild hydrogen-generating materials is of great significance to improve the working life of hydrogen–oxygen fuel cells. In this study, Al–Bi–Zn composite powders were designed by phase diagram calculation and then prepared via the gas atomization method. The results indicated that the conversion yield of Al–12Bi–7Zn (wt.%) powder reached 98% with stable hydrogen production within 280 min at 50 °C. When composite powder reacted with NaCl solution to produce hydrogen, the dormant period of the reaction process was significantly shortened, but the conversion rate was slightly reduced. Additionally, the evolution of powder morphology during the reaction was investigated. The results showed that the continuous cracking of the powder led to the continuous exposure of fresh Al to react.     

The enhanced photocatalytic activity of Na0.9Mg0.45Ti3.55O8 co‐loaded with silver and platinum

Noble metals Ag and Pt were loaded on Na_0.9Mg_0.45Ti_3.55O₈ (NMTO) by chemical bath deposition method, which was synthesized firstly in our recent work. The scanning electron microscopy and transmission electron microscopy results show that Ag and Pt nanoparticles were distributed on the different surfaces of NMTO. NMTO loaded with Ag and Pt can efficiently enhance the separation of photogenerated electron‐hole pairs, exhibiting much higher photodegradative ability for methylene blue and rhodamine B than the pure NMTO. The best weight concentrations of Ag and Pt are 9.00% and 3.70%, respectively. The electrostatic field is built in the Schottky barrier between NMTO and noble metals, leading to the energy band bending. Then, photogenerated electrons and holes are efficiently separated to enhance the photocatalytic activity.     

Predictive association of metal–organic systems in the solid-state: the molecular electrostatic potential based approach

Designing crystalline solids with improved properties or performances remains a challenging task, despite great strides that have been made within the field of crystal engineering since its birth several decades ago. Herein, we are bringing examples that illustrate recent successes in taking supramolecular synthetic guidelines from the organic crystal engineering and adjusting those to metal-containing systems, particularly to the lower-dimensional ones. The versatility of calculated molecular electrostatic potential (MEP) as a new crystal engineering tool is demonstrated.     

Facile fabrication of graphene oxide-polyethylenimine composite and its application for the Cr(VI) removal

A binary composite consisting of graphene oxide (GO) and polyethylenimine (PEI) was fabricated by a facile physical mixing. Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscope (FE-SEM), thermo-gravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and Zeta potential were used to characterize the prepared graphene oxide-polyethylenimine composite (GOPC). A series of experiments were carried out to investigate the effects of some important parameters, such as molecular weight of PEI, pH, time and temperature, on the adsorption efficiency of GOPC. Due to the high amine density of GOPC, its adsorption for Cr(VI) occurred more easily at lower pH mainly via electrostatic interaction. The adsorption process matched well with the Langmuir isotherm model and the pseudo-second-order kinetic model. The maximum adsorption capacity from the Langmuir model was 370.37 mg/g at pH 2.0 and 45°C for GOPC. Thermodynamic parameters revealed spontaneous and endothermic nature of the Cr(VI) adsorption onto GOPC. The main adsorption mechanism of GOPC toward Cr(VI) was electrostatic interaction. The adsorption-desorption experiments suggested GOPC was easily recycled and its stable adsorption capacity endowed it great potential as an adsorbent of Cr(VI) from wastewater.     

带扩张段构型超声速气流中横向射流数值模拟

针对带扩张段构型的发动机燃烧室,采用欧拉-拉格朗日仿真方法研究喷注方式、喷孔参数及隔离段燃烧室构型的改变对于射流雾化效果的影响,用以更好地指导发动机设计.结果表明,在保证发动机总体流量不变的条件下,喷孔孔径减小或者喷孔总数量减少使得液气动量通量比增大,有利于同时增大单孔射流穿透深度以及液滴展向宽度.贫燃工况下如当量比为0.7条件下,射流流量减小,混合效果可能变差.而在发动机结构设计方面,隔离段到燃烧室的过渡设计不宜采用大转角,15°转角是相对较为理想的设计方案.采用小角度突扩构型设计比渐扩构型更容易找到相对好的点火位置.