Microstructural and mechanical properties assessment of transient liquid phase bonding of CoCuFeMnNi high entropy alloy

The transient liquid phase (TLP) bonding of CoCuFeMnNi high entropy alloy (HEA) was studied. The TLP bonding was performed using AWS BNi-2 interlayer at 1050 °C with the TLP bonding time of 20, 60, 180 and 240 min. The effect of bonding time on the joint microstructure was characterized by SEM and EDS. Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time. For samples bonded at 20, 60 and 180 min, athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn₃Si intermetallic compound. For all samples, the γ solid solution was formed in the isothermal solidification zone of the bonding zone. To evaluate the effect of TLP bonding time on mechanical properties of joints, the shear strength and micro-hardness of joints were measured. The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints. The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min, respectively.     

基于C#持久蠕变强度外推功能的实现

持久蠕变强度外推是预测材料在高温高压环境下工作寿命的有效方法。目前常用的外推方法有等温法和参数法。这两种方法都是通过在实验室中采用较短时间的试验，获取试验数据后，通过Excel或者MATLAB等数据处理软件进行数据的拟合处理和外推计算。这些数据归纳统计和数学建模的过程有时需要耗费试验人员的大量精力。介绍了持久蠕变强度外推的软件实现方法，该功能包含在持久蠕变试验设备配备的软件中，试验完成后，软件直接根据试验结果进行数据拟合和持久蠕变强度的外推计算，无需试验数据的统计和建模，大大提高了持久蠕变强度外推计算的效率。     

等温退火对8030铝合金导线组织性能的影响

研究了不同等温退火工艺对8030铝合金导线组织及性能的影响。结果表明:等温退火前后合金均由α-Al基体和Al₆Fe相组成。在同一等温温度下,随着等温时间的延长组织逐渐趋于均匀化;同一等温时间下,随着等温温度的升高,组织趋于均匀化的时间缩短。经过等温退火处理后铝合金导线的导电率均有所提高,在470 ℃均匀化退火24 h后再经240 ℃等温4 h,合金导电率达到最高值57.21%IACS,比未经热处理试样的导电率提高了2.4%IACS。经过等温退火处理后铝合金导线的硬度及抗拉强度均有所降低,塑性大幅度提高。在470 ℃均匀化退火24 h后再经260 ℃等温8 h,合金的伸长率最高可达23.64%。热处理前后合金均为塑性断裂。     

自旋对角接触球轴承弹流润滑与油膜刚度的影响

根据角接触球轴承自旋运动特征，同时考虑弹流润滑效应，建立角接触球轴承考虑自旋运动的弹流润滑模型；采用多重网格法求解弹性变形，利用有限差分法迭代求解雷诺方程，得到较为精确的数值解；分析不同赫兹接触压力、滚道表面粗糙度下自旋对角接触球轴承弹流润滑和油膜刚度的影响。结果表明：考虑自旋时随着Hertz接触压力、自旋角速度增大，油膜厚度减小，油膜压力增大，油膜承压区域呈细长状，并向接触中心靠近；随着滚道表面粗糙度幅值增大，油膜压力和膜厚均出现了波动，且考虑自旋运动时，轴承油膜厚度明显减小，油膜局部压力峰值更大；随着卷吸速度、润滑油黏度增大，油膜刚度减小，而考虑自旋运动时油膜刚度值更大；随着自旋角速度增大，油膜刚度逐渐增大。     

Nb和时效时间对热轧中锰TRIP钢中P偏聚的影响

热轧态中锰TRIP钢首先经650 ℃退火2 h,随后在550 ℃进行等温时效热处理,采用场发射扫描电镜(FE-SEM)研究该钢中P的偏聚和时效析出行为的变化情况。结果表明,中锰TRIP钢中P在晶界的偏聚是一种非平衡偏聚现象,临界时间约为50 h,与理论计算结果48 h较为吻合。在局部偏聚区域内,C与P存在共偏聚的关系,即P偏聚量高的地方,C含量也高。而合金元素Nb具有抑制P偏聚的效果,在20~70 h时效时间内,可以相对降低6.57%~19.5%的最大P偏聚量。根据电子背散射衍射(EBSD)菊池线分析,P偏聚量低于2.28at%时,P为固溶状态,高于2.28at.%时,P为析出状态。     

考虑结构动态变形的缸套-活塞环润滑建模分析

缸套在燃烧冲击和活塞敲击激励下会产生接近表面粗糙度的动态变形,极有可能影响缸套-活塞环组件间的摩擦润滑过程。为了研究缸套动态变形潜在的影响,将动力学仿真获取的缸套内表面的动态变形经过处理后导入到润滑模型中,同时采用数值积分计算的方式对油液压力应力因子和剪切应力因子进行实时计算求解,使仿真计算更加符合实际情况。通过搭建同时考虑缸套变形与油液剪切特性影响的改进润滑模型,计算得到整个工作循环内活塞环上的最小油膜厚度和摩擦力曲线。结果表明:考虑缸套动态变形后的最小油膜厚度和摩擦力曲线出现了明显的波动,而且考虑缸套动态变形后的摩擦力比未考虑之前出现了明显下降。     

含煤盆地深层“超饱和”煤层气形成条件

中国深层煤层气资源丰富，但总体勘探和认识程度较低，尚未形成较为系统的深层煤层气地质理论。通过解剖分析准噶尔盆地白家海凸起和鄂尔多斯盆地临兴区块深层"超饱和"煤层气井的试气/生产动态，估算原地游离气的含气量，分析了深层"超饱和"煤层气的形成条件。研究表明：①深层"超饱和"煤层气储层中除吸附气外，还含有原地游离气，用常规试气方法可直接获得气流，煤层气的产出不明显依赖于排水降压；②埋藏超过一定深度，在煤阶和温度的综合作用下，煤的吸附能力将随埋深的继续增加而降低，煤层中吸附气的饱和度有增加的趋势，在达到吸附饱和后，出现原地游离气并形成"超饱和"煤层气，盆地深层具有"超饱和"煤层气形成的优势条件；③由于地温梯度和压力梯度的不同，不同盆地"超饱和"煤层气出现的临界深度不同，异常高压和异常高热流可以降低深层"超饱和"煤层气形成的临界深度；④深层"超饱和"煤层气开发具有大大缩短见气时间、充分利用地层能量和累积产水量低等优势，有望成为未来煤层气勘探开发的一个重要领域。     

Enhancing the Tribological Behavior of Lubricating Oil by Adding TiO2, Graphene,and TiO2/Graphene Nanoparticles

This article investigates the tribological behavior of nanoparticles (NPs) of titanium dioxide anatase TiO₂ (A), graphene, and TiO₂ (A) + graphene added to the pure base oil group ΙΙ (PBO-GΙΙ). The morphology of these two nanostructures of TiO₂ (A) and graphene was characterized by transmission electron microscopy (TEM). Oleic acid (OA) was blended as a surfactant into the formulation to help stabilize the NPs in the lubricant oil. A four-ball test rig was used to determine the tribological performance of six different samples, and an image acquisition system was used to examine and measure the wear scar diameter of the stationary balls. Field emission–scanning electron microscopy (FE-SEM) was used to examine the wear morphology. Energy-dispersive X-ray spectroscopy (EDX), element mapping, and Raman spectroscopy were employed to confirm the presence of (TiO₂ (A) + graphene) and the formation of a tribolayer/film on the mating surfaces. Moreover, a 3D optical surface texture analyzer was utilized to investigate the scar topography and tribological performance. The experiments proved that adding (0.4?wt% TiO₂ (A) + 0.2?wt% graphene) to the PBO-GΙΙ optimized its tribological behavior. These excellent results can be attributed to the dual additive effect and the formation of a tribofilm of NPs during sliding motion. Furthermore, the average reductions in the coefficient of friction (COF), wear scar diameter (WSD), and specific wear rate (SWR) were 38.83, 36.78, and 15.78%, respectively, for (0.4?wt% TiO₂ (A) + 0.2?wt% graphene) nanolubricant compared to plain PBO-GΙΙ lubricant.     

Wear and thermal behavior of basalt fiber reinforced rice husk/polyvinyl chloride composites

Plant fiber reinforced polymer composites (PFRPs) in practical application are often subjected to both complex friction and variable temperature environments. The present work explores the possibility of reinforcing rice husk/polyvinyl chloride (RH/PVC) composites with basalt fibers (BF) for developing a new wear resistant material with improved thermal stability. The results showed that the structural strength and wear resistance of the composites increased at first and then decreased with an increasing ratio of BF/RH, the highest value occurred at a BF/RH ratio of 8/42. The thermal stability of composites had a positive relationship with BF/RH ratio. The composites added with BF all possessed improved performance in comparison with unadded composites. Hence, the findings of this article proposed some new perspectives on improving the wear resistance and thermal stability of PFRPs that would broaden their practical application.