微通道板表面羟基化工艺研究北大核心

研究了3种微通道板基底羟基化的方法,测量了羟基化处理后微通道板基底表面水接触角及通道端面的形貌变化,分析了各种方法中微通道板基底的亲水性和腐蚀情况。实验结果表明:氨水双氧水溶液对基体表面的亲水性能提升不大,NaOH溶液对基体有腐蚀作用,经食人鱼溶液处理的基体表面亲水性明显提高且无腐蚀作用。研究了微通道板在食人鱼溶液中的浸泡时间和浸泡温度对表面亲水性的影响。结果表明:随着浸泡温度的增加,微通道板表面水接触角先减小后增大,当温度为80℃时达到极小值,浸泡时间对微通道板表面的亲水性影响不大。最终确定了微通道板表面羟基化工艺:浸泡温度为80℃,静置时间为20~60 min。     

Experimental study on uplift behavior of shallow anchor plates in geogrid-reinforced soil

Geogrid reinforcement can significantly improve the uplift bearing capacity of anchor plates. However, the failure mechanism of anchor plates in reinforced soil and the contribution of geogrids need further investigation. This paper presents an experimental study on the anchor uplift behavior in geogrid-reinforced soil using particle image velocimetry (PIV) and the high-resolution optical frequency domain reflectometry (OFDR). A series of model tests were performed to identify the relationship between the failure mechanism and various factors, such as anchor embedment ratio, number of geogrid layers, and their location. The test results indicate that soil deformation and the uplift resistance of anchor plates are substantially influenced by anchor embedment ratio and location of geogrids, whereas the number of geogrid layers has limited influence. In reinforced soil, increasing the embedment ratio greatly improves the ultimate bearing capacities of anchor plates and affects the interlock between the soil and geogrids. As the embedment depth increases, the failure surfaces gradually change from a vertical slip surface to a bulb-shaped surface that is limited within the soil. The strain monitoring data shows that the deformations of geogrids are symmetrical, and the peak strains of geogrids can characterize the reinforcing effects.     

行李箱外板浮动整形模设计

介绍了某轿车行李箱外板的翻边侧整形模设计过程,行李箱外板的侧法兰翻边上存在凹包,其翻边方向和凹包成形方向不同,常规需要2道工序分别完成翻边和凹包成形。该模具突破了传统的设计结构,在翻边机构中设置了凹包成形机构,将2个不同方向的成形复合到1道工序中,减少了模具数量,降低了冲压成本和工装成本。     

Experimental study on prediction model of wet gas pressure drop across single-orifice plate in horizontal pipes in the low gas phase Froude number region

The pressure drop prediction of wet gas across single-orifice plate in horizontal pipes had been solved satisfactorily under an annular-mist flow in the upstream of orifice plates. However, this pressure drop prediction is still not clearly determined when the upstream is in an intermittent flow or stratified flow, which is corresponding to a region of low Fr_G (gas phase Froude number) in the flow pattern map of wet gases. In this study, the wet gas pressure drop across a single-orifice plate was experimentally investigated in the low Fr_G region. By the experiment, the flow pattern transition in the downstream of single-orifice plates, as well as the effects of Fr_G and Fr_L (liquid phase Froude number) on Φ_G (gas phase multiplier), were determined and compared when the upstream is in the flow pattern transition and the stratified flow region, respectively. Prediction performances were examined on the available pressure drop models. It was found that no model could be capable of jointly predicting the wet gas pressure drop in the low Fr_G region with an acceptable accuracy. With a new method of correlating Fr_G and Fr_L simultaneously, new correlations were proposed for the low Fr_G region. Among which the modified Chisholm model shows the best prediction accuracies, with the prediction deviations of Φ_G being within 7% and 3% when the upstream is in flow pattern transition and stratified flow region, respectively.     

基于改进Faster R-CNN及YOLO的大角度车牌识别算法

随着大数据时代的到来,智慧城市等一系列概念的提出,人工智能开始在城市各个角落得到广泛应用。其中,车牌识别作为城市道路交通重要的一环,也取得了重大突破。基于深度学习的车牌识别一经提出,各类算法应用于车牌检测及识别上,对比于传统的车牌识别,大大提高了识别的速率和准确率。然而,在非限制条件下,如大角度车牌识别准确率仍有提升的空间。提出了一种改进的FasterR-CNN与YOLO的深度学习车牌识别算法,将对大角度下的车牌识别准确率达到了99.7%。由于是轻量型的框架,为后续的移动设备部署工作提供了便利。     

退火温度对新型锆合金薄板带材析出相和织构的影响

采用扫描电镜和超高分辨透射电镜,对具有良好冲制性能的新型锆合金薄板成品带材进行含晶粒、第二相粒子等在内的显微组织研究,并探索真空退火处理条件下温度对带材显微组织的影响。结果显示:新型锆合金薄板成品带材晶粒平均尺寸2.17 μm,存在{0001}<1010>和{0001}<1120>两种织构,大部分晶粒<1120>平行带材RD方向,较少晶粒<1010>平行带材RD方向;第二相粒子分布在晶粒内部及晶界,平均尺寸114 nm,尺寸较大的为不规则椭圆形的Zr-Nb-Fe相,尺寸较小的为圆形的β-Nb相;热处理退火温度降低,带材晶粒尺寸减小,第二相粒子细小弥散分布;新型锆合金薄板成品带材良好冲制性能主要源于轧制积累应变诱发再结晶过程进行充分,导致晶粒细小及孪晶发生破碎;相对轧制变形,退火对带材冲制性能影响不显著。     

ASME Ⅱ卷D篇表U数据作为设计校核中材料验收标准存在问题及探讨

ASME标准钢板对于短时高温抗拉数据无规定,但设备设计人员在校核时又要用到此数据,于是有些设计文件在技术要求中将ASME II卷表U的数据作为材料验收的标准。针对此种做法引发的争议及涉及的主要问题进行试验验证和分析探讨。研究结果表明,ASME II卷D篇表U中的数据是基于室温抗拉强度保证值,并根据拟合曲线将室温保证值提高了10%得到的,实测数据与ASME规范数据不一致,部分材料在250~350℃存在动态应变时效现象,但仍不满足设计要求。材料经模拟焊后热处理后性能下降,难以到达交货态的要求。给出了短时高温抗拉强度的选用建议。     

整体壁板离散填料滚弯成形有限元模拟

具有一定曲率外形的铝合金整体壁板属于典型的多筋零部件,传统弯曲成形工艺成形困难,容易产生多种缺陷。提出了离散填料辅助滚弯成形整体2A12T4铝合金壁板滚弯工艺,并通过实验与整体填料滚变成形进行了对比,同时采用有限元模拟技术,探究了离散填料辅助整体壁板滚弯成形中的影响因素。研究结果表明:填料数量、上下垫板厚度等因素对成形性能影响较大,填料在3~6块时成形稳定,可以有效地避免筋条屈曲与失稳;随垫板厚度增加,壁板表面圆弧更加光滑、连续,但是回弹性增强;上下垫板分别在10~20 mm厚度时,综合性能较好。通过离散填料辅助滚弯技术可以成形出质量较高的整体壁板。     

Effect of clad ratio on interfacial microstructure and properties of cladding billets via direct-chill casting process

Numerical simulation and experiments were introduced to develop AA4045/AA3003 cladding billets with different clad-ratios. The temperature fields, microstructures and mechanical properties near interface were investigated in detail. The results show that cladding billets with different clad-ratios were fabricated successfully. Si and Mn elements diffused across the bonding interface and formed diffusion layer. With the increase of clad-layer thickness, the interfacial region transforms from semisolid–solid state to liquid–solid state and the diffusion layer increased from 10 to 25 μm. The hardness at interface is higher than that of AA3003 side but lower than that of the other side. The bonding strength increased with the clad-layer thickness, attributing to solution strengthening due to elements diffusion. The cladding billets were extruded into clad pipe by indirect extrusion process after homogenization. The clad pipe remained the interfacial characteristics of as-cast cladding billet and the heredity of clad-ratio during deformation was testified.