天然气水合物储层泥质细粉砂挡砂介质堵塞规律与微观挡砂机制

中国南海海域部分天然气水合物储层中地层砂为高泥质含量细粉砂，开采防控砂难度较大。针对高泥质细粉砂挡砂机制问题，使用粒度中值为10.13 μm的泥质细粉砂样品，模拟单向气液携砂流动条件，使用绕丝筛板、金属烧结网、金属纤维、预充填陶粒4类挡砂介质在20~80 μm挡砂精度下进行挡砂模拟实验，采用显微成像系统观察挡砂介质内部及表面砂粒沉积与堵塞动态，分析介质流通性能和挡砂性能变化，总结堵塞规律、微观挡砂机制与形态及其控制因素。研究结果表明，不同类型和精度的挡砂介质对泥质细粉砂的堵塞总体呈现堵塞开始、堵塞加剧和堵塞平衡3个阶段。随着驱替进行，挡砂介质渗透率逐渐降低，幅度会高达90%以上；同时过砂速度减缓，最终过砂率为5%~10%。根据堵塞规律和微观图像分析，提出了粗组分分选桥架、局部砂团适度挡砂、整体砂桥阻挡等挡砂介质对泥质细粉砂的3种微观挡砂机制。以粗组分分选桥架挡砂机制为主的挡砂工况下，挡砂介质堵塞渗透率较高，但过砂率超过15%，挡砂效果较差；以整体砂桥挡砂机制为主时，过砂率在10%以下，挡砂性能较好，但各类挡砂介质的堵塞渗透率不足1 D，流通性能较差。局部砂团适度挡砂机制为主时介质挡砂性能及流通性能介于两者之间。挡砂介质对天然气水合物储层泥质细粉砂的微观挡砂机制和形态受挡砂介质类型、精度、地层砂特征以及流动条件等因素控制，其规律对于水合物泥质细粉砂防控砂优化有指导意义。     

海上热采防砂封隔器研制与室内试验

海上稠油热采开发过程中,通常采用蒸汽吞吐的方式进行原油开采。为满足稠油热采长效密封要求,研制了HPHT-215型热采防砂封隔器。封隔器胶筒采用特制的氟硅基复合材料+玻璃纤维网结构,并开展了材料性能评价测试。通过有限元分析和室内胶筒组合测试,对胶筒材料和组合结构进行了评价优化。室内全尺寸整机测试表明:封隔器能够满足耐温350 ℃、耐压21 MPa密封性能要求,并开展了高低温多轮次密封性能评价测试。该型热采防砂封隔器的研制成功,为海上稠油蒸汽吞吐多轮次开发提供了保障,具有广泛的应用前景。     

乌兰矿采矿现状及技术应对方案

本文分析了乌兰矿投产前期采矿现状及存在的主要问题,针对该矿所处蒙古国经济落后、投资风险大的现实状况,为避免生产中断、规避投资风险,早日回收前期投资考虑,采取了双斜坡道开拓、全尾胶结充填、高端壁空场嗣后充填采矿、多中段组合式连续开采等系列技术应对方案。大大降低了一次性投资规模及投资风险,前期投资得以快速回笼的同时,矿山产能也充分释放,确保了矿山的持续稳定,取得了较好的经济和社会效益。为海外地下近地表矿体开采矿山规避投资风险提供了很好的技术方案借鉴。     

Effect of fiber-reinforcement on the mechanical behavior of sand approaching the critical state

Several types of ground improvement methods that employ fiber-reinforcement have been developed in recent years. A series of consolidated drained triaxial compression tests has been conducted here to examine the effect of short fibers on the mechanical properties of Toyoura sand. Sand with 0%, 0.2%, 0.4%, and 1% fiber contents, prepared to yield random distribution, was sheared under several confining pressures and controlled via their initial relative densities. The test results showed that the maximum and residual deviatoric stresses increased, whereas the volumetric expansion decreased with an increase in fiber content. Although the stress ratio η (=q/p′) and specific volume changed depending on the fiber content and confining pressure with shear progression, they each reached the same values for a definite fiber content at the end of shearing, independent of initial relative density. In other words, the unique critical state line can be found for a definite fiber content. Moreover, the greater the fiber content, the larger the slope of the critical state line at the end of shearing. Additionally, as the length of fibers shortened with the same percentage of fiber inclusions in sand, the deviatoric stress and the stress ratio decreased, approaching the shear-strain-volumetric response of unreinforced sand.     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

Ceramics composites from iron ore tailings and blast furnace slag

The search for materials and methods capable of reducing human impacts on the environment is of utmost importance nowadays. This study's primary purpose was to analyze the technical feasibility of ceramic composites production utilizing Fundão Dam's Iron Ore Tailings (IOT), Blast Furnace Slag (BFS) from charcoal, and Foundry Sand (FS) as partial substitutes for the traditional raw materials – sand and clay – for application in building industry materials. The composites were molded in rectangular specimens and fired at temperatures of 900, 950, 1000, 1050, and 1200 °C. The developed materials were analyzed and characterized by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), Thermogravimetry (TGA), and Differential Thermal Analysis (DTA). The obtained materials had flexural strength modulus of up to 12.19 MPa, water absorption ranging from 2 to 22%, linear shrinkage ranging from 0.02 to 6.50%, and apparent density ranging from 2.03 to 1.63 g/cm³. The study of the internal structure formation process revealed the formation of amorphous structures in the composites. The results demonstrated that these waste materials may be jointly used in construction materials, contributing to the reduction of natural resource extraction, besides enabling their correct disposal, minimizing environmental impacts, and improving the life quality of the surrounding communities.     

The influence of volume fraction of amorphous phase on corrosion resistance of Mg67Zn 29Ca 4 alloy

The aim of this study was to investigate the structure and corrosion resistance of amorphous, amorphous‐crystalline, and crystalline Mg₆₇Zn₂₉Ca₄ alloy for biodegradable applications. This paper presents a preparation method and results of the structural characterization and corrosion resistance analysis of the material. Samples were prepared in the form of 3 mm diameter rods. The structure of the alloy was examined with the use of X‐ray diffractometry and scanning electron microscopy. The thermal properties of the samples were examined with differential scanning calorimetry (DSC). Results of DSC analysis were used to determine heat treatment temperatures, allowing to obtain different fractures of crystalline phase in the material. Corrosion resistance of heat‐treated samples was investigated by immersion tests and electrochemical measurements performed in the simulated body fluid. The X‐ray diffraction results confirmed that the prepared Mg₆₇Zn₂₉Ca₄ alloy's structure is fully amorphous. After heat treatment, samples with different fractions of amorphous phase in the structure were obtained. Immersion tests of the samples showed that the structure significantly influenced corrosion resistance in examined materials. It should be pointed out, that certain amounts of crystalline phase in amorphous matrix can greatly improve the corrosion resistance of Mg₆₇Zn₂₉Ca₄ alloy.     

海月构造带东三段滩坝砂分布及成藏主控因素分析

辽河滩海地区海月构造带东三段沉积期,三角洲前缘砂体受湖岸流和波浪的改造,形成了一系列滩坝砂沉积,细分为滩砂和坝砂,水动力强则形成坝砂,水动力弱则形成滩砂;滩坝砂平行于湖岸线呈带状分布,易于形成岩性圈闭。滩坝砂受砂体发育规模、储层物性、断裂输导体系及封堵性等多种因素控制,在滩坝砂较为发育的东三下段,靠近海南断层、盖州滩断层且封堵条件优越的滩坝砂最易于成藏。     

提高加盖钢包自开率的研究与实践

首钢京唐300t钢包加盖后自开率明显下降，分析了加盖钢包自开率下降的机理，确定了主要原因是包衬温度升高后造成的液态渣回流。通过对引流砂的流动性、密度和渗钢性研究，设计了一种适用于加盖钢包的引流砂成分配比，并通过控制Al2O3和MgO含量，保证铬矿砂纯度。改进了钢包热修工艺，设计了针对加盖钢包的投砂操作和防钢渣回流措施。研究结果经推广使用后，钢包月不自开炉数由8～9炉降低至2炉以内，综合自开率达99.9%，双精炼工艺自开率达100%。     

优化特征提取的互动式人脸活体检测研究

针对人脸识别系统中出现的通过照片或视频“欺诈”解锁问题，提出一种活体检测方法，通过随机指令判断被检测对象是否为真人。利用HOG特征和随机森林算法对摄像头采集的图像进行人脸检测，预测脸部68个特征点位置，把68个特征点位置和脸部位置的相对位置归一化后作为姿态的特征，提取的姿态特征与SVM分类器相结合，训练出分类效果较好的头部姿态估计分类器。通过多次实验，对特征提取方法进行优化，进一步提高检测准确率。最后，使用随机互动式命令序列对被检测人发出指令，实现活体检测。该方法对头部姿态估计具有较高的鲁棒性，并且可以有效地防范照片和视频认证攻击。