微纳层叠聚丙烯腈凝胶流动特性的数值模拟研究

建立了层叠流道的三维模型和有限元网格模型，根据流变测试数据，采用Polymat对物料的黏度模型参数进行拟合，并利用Polyflow软件对聚丙烯腈（PAN）凝胶在层叠流道内的三维等温流动过程进行了数值模拟分析。研究发现，当入口流量增大时，层叠流道出口速度的不均匀性增加；沿流动方向流道内压力逐渐降低，并在出口处降低至同一最低值；流道进出口压力差与入口流量大小具有正相关性；在流道的中心截面上剪切速率分布均匀，波动较小。     

地表径流速度对城市内涝影响规律

为分析地表径流速度对城市内涝的影响,采用一维地下排水管网与二维城区地形的动态耦合模型,选取大连市某排水区块作为研究区域,设置4种地表径流速度10种设计降雨场景,模拟分析在不同重现期设计降雨及不同地表径流速度下研究区的内涝积水特性。结果表明:随着地表径流速度降低,管道排水压力变小,管道排水达标率最高可提升48.05%,且降雨重现期越短,地表径流流速对管道排水压力的削减效果越明显;地表径流流速对检查井溢流量影响显著,随着地表径流速度降低,检查井溢流量峰值最高可减小2 750 m~3,峰现时间最长可滞后56 min,同时随着降雨重现期增长,地表径流流速对检查井溢流量的削减效果减弱;研究区低、高风险区淹没面积随地表径流速度降低,最高可分别减小1.64万、8.37万m~2,但中风险区淹没面积变化反复。     

基于CFD⁃DEM的水下切粒装置水室内颗粒流动过程数值模拟

基于CFD?DEM耦合方法，研究了颗粒在水室内的流动状态，分析了不同刀盘转速、粒子水通入量和水室出口角度对造粒过程的影响，发现提高刀盘转速、增加粒子水通入量和水室出口倾斜一定的角度都有利于水室内颗粒的排出。进一步研究了颗粒与碎屑在水室内的流动，发现在水室出口处二者的流动基本呈现出一定的分离角度。     

The effects of washing a collagen sample prior to TEM examination

Transmission electron microscopy (TEM) is an important analysis technique to visualize (bio)macromolecules and their assemblies, including collagen fibers. Many protocols for TEM sample preparation of collagen involve one or more washing steps to remove excess salts from the dispersion that could hamper analysis when dried on a TEM grid. Such protocols are not standardized and washing times as well as washing solvents vary from procedure to procedure, with each research group typically having their own protocol. Here, we investigate the influence of washing with water, ethanol, but also methanol and 2-propanol, for both mineralized and unmineralized collagen samples via a protocol based on centrifugation. Washing with water maintains the hydrated collagen structure and the characteristic banding pattern can be clearly observed. Conversely, washing with ethanol results in dehydration of the fibrils, often leading to aggregation of the fibers and a less obvious banding pattern, already within 1 min of ethanol exposure. As we show, this process is fully reversible. Similar observations were made for methanol and propanol. Based on these results, a standardized washing protocol for collagenous samples is proposed.     

高熔体流动速率薄壁注塑聚丙烯专用料的结构与性能分析

采用多种分析测试方法，对3类高熔体流动速率薄壁注塑聚丙烯（PP）专用料的熔融结晶性能、光学性能、分子量分布、力学性能、毛细管流变性能、热收缩性能进行了分析研究。结果表明，K1860与2种市售主流PP1、PP2各项性能相当，其中K1860分子量分布相对PP1、PP2较窄，弯曲性能、拉伸性能更优，可满足大型薄壁注塑制品的生产要求。     

我国中空吹塑行业发展现状及“十四五”期间重点产品、工艺和设备发展方向

从原料、中空成型机和吹塑工艺等方面介绍了我国中空吹塑行业发展现状，并对电子化学品专用超洁净桶、高压储氢四型瓶、全电动中空成型机、微发泡中空成型技术和挤吹聚对苯二甲酸乙二醇酯（PET）容器等在“十四五”期间的重点产品、工艺和设备发展方向进行了展望。     

Microstructure and Mechanical Properties of Mg–RE–TM Cast Alloys Containing Long Period Stacking Ordered Phases: A Review

Casting magnesium alloys hold the greatest share of magnesium application products due to their short processing period, low cost and near net shape forming. Compared with conventional commercial magnesium alloys or other Mg–RE-based alloys, the novel Mg–RE–TM cast alloys with long period stacking ordered(LPSO) phases usually possess a higher strength and are promising candidates for aluminum alloy applications. Up to now, two ways: alloying design and casting process control(including subsequent heat treatments), have been predominantly employed to further improve the mechanical properties of these alloys. Alloying with other elements or ceramic particles could alter the solidifi cation pattern of alloys, change the morphology of LPSO phases and refi ne the microstructures. Diff erent casting techniques(conventional casting, rapidly solidifi cation, directional solidifi cation, etc.) introduce various microstructure characteristics, such as dendritic structure, nanocrystalline, metastable phase, anisotropy. Further heat treatments could activate the transformation of various LPSO structures and precipitation of diverse precipitates. All these evolutions exert great impacts on the mechanical properties of the LPSO-containing alloys. However, the underlying mechanisms still remain a subject of debate. Therefore, this review mainly provides the state of the art of the casting magnesium alloys research and the accompanying challenges and summarizes some topics that merit future investigation for developing high-performance Mg–RE–TM cast alloys.     

海洋非成岩天然气水合物原位快速制备实验及评价

我国的海洋天然气水合物（以下简称水合物）资源主要分布在沿海大陆架水深介于300～3 000 m的深水区，具有弱胶结、非成岩的特征，为了测试和研究该类型水合物必须原位、大量、快速制备样品，而目前常用的搅拌法、喷淋法、鼓泡法等制备技术却存在着生成速度慢、储气密度低等问题。为此，自主设计、研制了1 062 L非成岩水合物快速制备釜，针对我国南海非成岩水合物的物性特征，开展了搅拌法、鼓泡法、喷淋法单一制备方法及“三合一”法（上述3种方法相结合）水合物制备实验，测试了实验过程中温度、压力、电阻率及反应时间等数据，分析比较了几种不同制备方法的水合物生成情况与制备效率。实验结果表明：①搅拌法、鼓泡法、喷淋法制备水合物过程中，生成的水合物均缓慢增加并逐渐铺满整个液面；②搅拌法制备过程中可以观测到明显的诱导期，而喷淋法、鼓泡法及“三合一”法却无明显的诱导期；③单一制备方法及“三合一”法制备水合物过程中，电阻率均随反应时间的增加而增加，其变化趋势亦与水合物制备速率基本一致；④“三合一”法的制备周期明显短于单一制备方法（搅拌法、喷淋法、鼓泡法单一方法的制备时间分别约为“三合一”法的5.14倍、3.59倍、3.16倍）。结论认为，所研制的1 062 L水合物快速制备釜能够实现海洋非成岩水合物样品的原位、快速制备；较之于单一制备方法，“三合一”法大大提高了水合物的制备效率。     

热处理对挤压态Mg-6Gd-5Y-1Zn合金组织与性能的影响

通过对Mg-6Gd-5Y-1Zn(质量分数,%)合金在固溶和时效处理状态下显微组织和力学性能的研究发现,α-Mg基体、沿挤压方向分布的条状18R-LPSO相、少量的Mg₂₄(GdYZn)₅ 相以及细层片状的14H-LPSO相构成了挤压态合金的组成相。挤压态合金经固溶(T4)处理后,一部分18R-LPSO相溶入基体,并且基体中的14H-LPSO相伸长同时粗化。挤压态合金经过固溶加时效(T6)处理后,大量β′相从α-Mg基体中析出。T6态合金的室温力学性能最好,其屈服强度、抗拉强度及伸长率分别为272 MPa、406 MPa和6.1%。β′相沉淀也发生在挤压态合金的直接人工时效(T5)处理过程,但相比于T6处理,14H-LPSO相和β′相在基体中的体积分数均偏低。     

线性富磷化阻燃剂在聚氨酯泡沫中的应用研究

通过界面聚合法合成了一种线性富磷化阻燃剂（LPRFR），将LPRFR与可膨胀石墨（EG）复配制备了阻燃聚氨酯泡沫（RPUF），使用红外光谱分析仪、核磁共振分析仪对阻燃剂LPRFR的化学结构进行了表征，并通过极限氧指数仪、锥形量热仪、扫描电子显微镜和红外光谱分析仪对RPUF的燃烧性能、微观形貌和化学结构进行了分析。结果表明，仅10 %（质量分数，下同）的LPRFR 与8 %EG复配后，RPUF的极限氧指数（LOI）便达到26.1 %；LPRFR和EG能大幅降低RPUF的热释放速率，并提高基体的成炭能力； LPRFR参与了燃烧过程中的成炭反应，形成了含P—O—C及P=O结构的高质量炭层，有效隔绝了氧气和热量；LPRFR是一种对于聚氨酯泡沫阻燃性能优异的新型阻燃剂。