基于纸喷雾离子化衍生质谱法快速检测PM2.5中的醌污染物

醌类化合物是PM2.5中的一类有害物质。本研究建立了纸喷雾离子化衍生质谱法快速测定PM2.5中的醌类污染物。通过衍生化反应在醌化合物中引入氨基，提高醌在纸喷雾中的离子化效率。随后对衍生化试剂种类、电压、喷雾溶剂种类等反应条件进行优化。在最优实验条件下，采用内标法定量分析1,4-苯醌、甲基对苯醌、1,4-萘醌和1,4-蒽醌，4种化合物均呈现较好的线性关系，其检出限分别为4.49、20.89、0.13、0.17 ng。利用该方法分析PM2.5实际样品中的萘醌和蒽醌，均获得了较好的定性和定量结果。     

One-step to prepare high-performance gas diffusion layer (GDL) with three different functional layers for proton exchange membrane fuel cells (PEMFCs)

Gas diffusion layer (GDL) is one of the most important components of fuel cells. In order to improve the fuel cell performance, GDL has developed from single layer to dual layers, and then to multiple layers. However, dual or multi layers in GDL are usually prepared by layer-by-layer methods, which cost too much time, energy, and resources. In this work, we successfully developed a facile one-step method to prepare a GDL with three functional layers by utilizing the different sedimentation rates and filtration rates of short carbon fiber (CF) and carbon nanotube (CNT). The treatment temperature for this GDL is much lower than that of traditional method. The thickness of the GDL can be effectively controlled from as thin as 50 μm to more than 200 μm by simply adjusting the content of CF. The GDL with high flexibility is suitable to develop high performance flexible electronics. The fuel cell with the GDL has the maximum power density 1021 mW cm^?2, which shows 19% improvement comparing to the conventional one. Therefore, this work breaks the traditional concept that GDL for fuel cells only can be prepared by very complex and high-cost procedure.     

Investigation of fabrication of gas diffusion substrate for proton exchange membrane fuel cells

The gas diffusion substrate (GDS) is essential in the proton exchange membrane fuel cells. Its fabrication techniques affect the performance significantly and are worthy of investigation. In this study, a manufacturing process of the GDS is proposed to understand the formation process of GDS and promote its structure and performance more pertinently. Different states during the preparation process, raw carbon paper, pre-curing, curing, carbonation, and graphitization, are characterized and measured. Experimental and numerical methods are employed to determine the relationships between microstructure, transport, and mechanical performance variation with the fabricating processes. The results show that its porosity, average pore size, and effective diffusivity decrease first and increase after curing. These parameters after graphitization are lower than that of the carbon paper (CP). The electrical resistivity increases dramatically while pre-curing and decreases gradually after curing, carbonation, and graphitization, and it is much reduced after graphitization. Moreover, mechanical measurement results show that both the picks of tensile strength and flexural modulus occur after curing. Its tensile strength shows little change after graphitization compared to the initial paper's. In contrast, the flexural modulus is improved significantly.     

Moulded pulp products manufacturing with thermoforming

For an effective optimization of pulp thermoforming and of the moulded pulp products manufactured by this process, a full understanding of the process physics combined with full knowledge of the pressing equipment is necessary. For this reason, in this Addendum, we clarify how the process parameters “Holding time,” “Vacuum time,” “Cycle time,” and “Temperature” were interpreted and subsequently defined for the analysis of the process and product‐related outputs of the thermoforming experiments.     

On the capacity of the state‐dependent interference relay channel

This paper considers the state‐dependent interference relay channel (SIRC) in which one of the two users may operate as a secondary user and the relay has a noncausal access to the signals from both users. For discrete memoryless SIRC, we first establish the achievable rate region by carefully merging Han‐Kobayashi rate splitting encoding technique, superposition encoding, and Gelfand‐Pinsker encoding technique. Then, based on the achievable rate region that we derive, the capacity of the SIRC is established in many different scenarios including (a) the weak interference regime, (b) the strong interference regime, and (c) the very strong interference regime. This means that our capacity results contain all available known results in the literature. Next, the achievable rate region and the associated capacity results are also evaluated in the case of additive Gaussian noise. Additionally, many numerical examples are investigated to show the value of our theoretical derivations.     

总变差模型在书画打印宣纸印刷质量预测中的应用

为了建立适用于书画打印宣纸印刷质量的预测模型,本研究测量了14种书画打印宣纸的粗糙度、白度、不透明度、定量、光泽度和针对宣纸特别设定的帘纹深浅以及帘纹疏密度等表面物理参量,并在相同条件下,使用喷墨打印设备输出并测量印品色度值,利用总变差模型构建去除帘纹色差的测定方法,得到与人眼视觉特征相符的色差。运用GRNN广义回归神经网络结合书画打印宣纸表面物理参量与宣纸去帘纹后的色差值,建立预测模型。结果表明,该模型能够在仅测量书画打印宣纸表面物理参量的情况下,便能较为准确地预测书画打印宣纸印刷质量,为书画打印宣纸印刷前的选纸工作提供指导依据。     

Fabrication and characterization of MnO2 based composite sheets for development of flexible energy storage electrodes

Development of cost efficient, flexible and light weight paper electrodes for high-tech applications is high in demand in era of modern disposable technology. In this study α-MnO₂ nanorods were fabricated through hydrothermal method by varying growth time and further combined with lignocelluloses fibers extracted from self growing plant, Monochoria Vaginalis. Crystal structure, morphology and thermal properties of MnO₂ nanorods were characterized by X. Ray Diffraction (XRD), Field Emission Scanning Electron Microscope (FESEM) and Thermogravimetric Analysis (TGA), respectively. FESEM image analysis revealed the highest aspect ratio of 48.016 for 4?h treated MnO₂ sample and high purity level was confirmed by XRD. MnO₂ sample with high aspect ratio, relatively pure and larger yield was selected for incorporation of lignocelluloses fibers to fabricate flexible, light-weight and environmentally safe LC/MnO₂ composite paper sheet. Furthermore, LC/MnO₂ composite sheet was employed as working electrode in 2?M sodium sulfate electrolyte for cyclic voltammetry measurements. Presented LC/MnO₂ composite sheet revealed specific capacitances 117, 59, 39, 25 and 23?F/g at scan rates of 5, 10, 20, 50 and 100?mV/s, respectively. Incorporation of LC fibers within MnO₂ nanorods as binders will open the possibilities to fabricate the flexible paper electrode for application in supercapacitors and batteries due to facile synthesis, light-weight and environmentally friendly aspects.     

Synthesis of ZnO rod arrays on aluminum recyclable paper and effect of the rod size on power density of eco-friendly nanogenerators

In this work, we demonstrated a novel and effective approach on the use of low-cost electrodes, an eco-friendly substrate and zinc oxide (ZnO) micro or nanorods (MRs or NRs, respectively) for building triboelectric devices (TENGs). The reported strategy focuses on using low-cost materials and fabrication processes. For the first time and without any pre-treatment, an aluminum recyclable paper from the milk carton (named ARP) was used as a substrate and TENG bottom electrode. A systematic study on the growing of ZnO structures on ARP by chemical bath deposition has been carried out. We found that the ZnO rods size, and resistivity of the TENG upper electrode considerably influence the power density of the device. Such sustainable, low-priced ZnO-based TENGs can produce up to 1.6μW/cm² output power density when operated at 50?Hz. The fabrication of an eco-friendly nanogenerator demonstrates the possibility of manufacturing low-cost, flexible, and large-area energy harvesting devices for future applications.     

Effects of chemical etching on structure and properties of Y0.5Gd0.5Ba2Cu3O7-z coated conductors

Corrosion resistance is a crucial property to achieve successful superconducting joints of Y_0.5Gd_0.5Ba₂Cu₃O_7-z (YGdBCO) coated conductors (CCs). Cu and Ag metallic layers need to be fully removed from the area of conductor to be joint to allow for a superconducting path across the joint. Therefore, when using a wet etching process to remove the metallic layers, the joint performance can be significantly influenced by the etching conditions. The effects of chemical etching with ammonia water and hydrogen peroxide mixture on crystal structure, surface microstructure and critical current (I_c) of YGdBCO CCs were systematically investigated. We found the set of etching parameters that does not affect conductor performance, leaving the I_c of the YGdBCO conductor unchanged upon etching. However, when the etching conditions are not optimal, decrease in I_c was found and the underlying reasons driving the degradation were investigated. Raman spectroscopy and XRD analysis indicated that the reduced I_c is mainly due to oxygen deficiency in the YGdBCO crystal lattice.