汽车加油口双色注射模设计

分析了汽车加油口塑件结构,确定了注射成型方案、进胶方式,并介绍了通过滑块与开模动作配合实现塑件脱模的过程。     

Nitrogen Removal Performance of Denitrifying Ammonium Oxidation System in Treating Sulfamethoxazole-laden Secondary Wastewater Effluent

In this study,nitrogen removal performance of the denitrifying ammonium oxidation(DAO)process was investigated when treating sulfamethoxazole(SMX)-laden secondary wastewater effluent.The influent SMX concentration showed negligible effect on efficiencies for removal of nitrate and COD.However,the ammonium ions removal rate was moderately reduced,when the influent SMX concentration in wastewater reached 6 mg/L.Total nitrogen removal efficiency remained as high as 76.77%towards the day 158 at the end of experiment.Candidatus_Brocadia and Candidatus_Kuenenia were the functional anammox strains.The unclassified_f__Rhodobacteraceae sp.was predominant heterotrophic denitrifying strain in the studied reactor.The concentrations of soluble extracellular polymeric substances in sludge obviously increased from 16.76 mg/g VSS to 32.31 mg/g VSS,which might protect the nitrogen removal strains from high-concentration SMX.This result provides a theoretical and technical foundation for the application of denitrifying ammonium oxidation process in treating sulfamethoxazole-laden secondary wastewater effluent.     

Preparation of faceted TaN grains by heating Ta-containing oxides in BN crucible with Na

Single-crystal grains of TaN were synthesized by heating Ta₂O₅, FeTa₂O₆, or FeTaO₄ in a BN crucible together with Na metal in an Ar atmosphere at 1100 °C. The BN crucible acted a solid source of nitrogen. Aggregates of columnar ε-TaN single crystals 10–150 μm in size were formed on the inner wall of the BN crucible when either Ta₂O₅ or FeTa₂O₆ was used. On the other hand, platelet-like single crystals of θ-TaN 1–50 μm in size were obtained from FeTaO₄. The results of wavelength-dispersive X-ray spectrometry indicated that the compositions of the ε-TaN and θ-TaN crystals were close to the stoichiometric ideal.     

人造金刚石填充聚酰亚胺树脂基复合材料防刺性能

为研究树脂材料的防刺性能及防刺机制,利用手糊成型与热压法成型制备了手糊分层结构和均布结构层2种结构的人造金刚石填充聚酰亚胺树脂基复合树脂片,并探讨了人造金刚石粒径、填充体积分数对树脂片防刺性能的影响。研究结果表明:经过人造金刚石填充的聚酰亚胺树脂片的防刺性能得到提高,并且均布结构层分层复合结构的树脂片的防刺性能更好;随着人造金刚石粒径的减小,树脂片防刺性能出现先减小后增加的趋势,故防刺机制基本在于碰撞概率与树脂基的防挡;比较防刺力和消耗功发现,不同填充体积分数的单层防刺树脂片的防刺性能随人造金刚石填充体积分数的增加而逐渐降低,该趋势的成因在于复合树脂片的脆化与破坏;在颗粒等效粒径为300 μm、体积分数为10%时,其防刺性能最好。     

氮含量对HPD-1双相不锈钢组织及力学性能的影响

通过显微组织观察与力学性能测试研究了氮含量(0.08%~0.22％,质量分数)对HPD-1双相不锈钢硬度、拉伸性能、低温冲击性能及疲劳性能的影响。结果表明,氮含量变化可显著影响试验钢γ/α相比例,当氮含量由0.08％升高到0.22％,γ相含量由38.1％提高至56.5％。α相的硬度由273 HV10提高到343 HV10,γ相的硬度由238 HV10提高到299 HV10,试验钢强度明显提升。氮元素对两相比例和奥氏体相韧性的双重影响导致试验钢低温冲击性能呈先上升后下降的趋势;更高的氮含量抑制疲劳裂纹萌生与拓展,是影响HPD-1双相不锈钢室温疲劳性能的主要因素。撕裂棱是疲劳断口的显著特征。     

载铜树脂处理高含盐氨氮废水的性能

针对高含盐氨氮废水，选择具有不同功能基团的树脂为载体，进行负载Cu2+改性制得载铜树脂并对其处理高含盐氨氮废水的性能进行研究。在筛选出最佳载铜树脂的基础上，研究pH及Na+浓度、树脂投加量、反应时间对载铜树脂处理高含盐氨氮废水效果的影响，通过对吸附氨氮前后的载铜树脂进行SEM和EDS表征分析并构建吸附动力学模型以进一步探究配位吸附的过程。结果表明，Cu2+可与螯合树脂D751稳定结合且在宽pH值下均表现出耐盐性和良好的氨氮吸附效果；在室温(25℃)、pH=11及Na+浓度4 g/L、树脂投加量8 g/L、反应时间60 min的条件下，D751载铜树脂对氨氮的去除率为34.8%。D751载铜树脂吸附氨氮后其表面出现明显的晶状结构物质，该物质可能为铜氨络合物。D751载铜树脂对高含盐氨氮的吸附符合准二级动力学模型。     

整体壁板离散填料滚弯成形有限元模拟

具有一定曲率外形的铝合金整体壁板属于典型的多筋零部件,传统弯曲成形工艺成形困难,容易产生多种缺陷。提出了离散填料辅助滚弯成形整体2A12T4铝合金壁板滚弯工艺,并通过实验与整体填料滚变成形进行了对比,同时采用有限元模拟技术,探究了离散填料辅助整体壁板滚弯成形中的影响因素。研究结果表明:填料数量、上下垫板厚度等因素对成形性能影响较大,填料在3~6块时成形稳定,可以有效地避免筋条屈曲与失稳;随垫板厚度增加,壁板表面圆弧更加光滑、连续,但是回弹性增强;上下垫板分别在10~20 mm厚度时,综合性能较好。通过离散填料辅助滚弯技术可以成形出质量较高的整体壁板。     

装填设备载荷影响因素分析及动力学仿真

大型货物的装填过程中影响载荷的因素较多,其中对中精度对装填载荷影响较为明显。通过动力学仿真软件ADAMS对装填过程中载荷进行模拟,并对各影响因素进行定量分析,得到对中偏差与装填载荷的关系。将仿真结果与试验数据进行对比,验证该仿真方法的正确性,可作为后续研究装填载荷的一种方法,为结构设计提供指导。