Direct ink writing of vancomycin-loaded polycaprolactone/ polyethylene oxide/ hydroxyapatite 3D scaffolds

Novel inks were formulated by dissolving polycaprolactone (PCL), a hydrophobic polymer, in organic solvent systems; polyethylene oxide (PEO) was incorporated to extend the range of hydrophilicity of the system. Hydroxyapatite (HAp) with a weight ratio of 55–85% was added to the polymer-based solution to mimic the material composition of natural bone tissue. The direct ink writing (DIW) technique was applied to extrude the formulated inks to fabricate the predesigned tissue scaffold structures; the influence of HAp concentration was investigated. The results indicate that in comparison to other inks containing HAp (55%, 75%, and 85%w/w), the ink containing 65% w/w HAp had faster ink recovery behavior; the fabricated scaffold had a rougher surface as well as better mechanical properties and wettability. It is noted that the 65% w/w HAp concentration is similar to the inorganic composition of natural bone tissue. The elastic modulus values of PCL/PEO/HAp scaffolds were in the range of 4–12 MPa; the values were dependent on the HAp concentration. Furthermore, vancomycin as a model drug was successfully encapsulated in the PCL/PEO/HAp composite scaffold for drug release applications. This paper presents novel drug-loaded PCL/PEO/HAp inks for 3D scaffold fabrication using the DIW printing technique for potential bone scaffold applications.     

Ternary type BaY2ZnO5: Eu3+ deep-red phosphor for possible latent fingerprint,security ink and WLED applications

Pc-WLEDs are considered to play a spectacular role in future generation light sources in view of their outstanding energy efficiency. In this regard, Eu³⁺ activated BaY₂ZnO₅ phosphor was prepared and investigated by XRD, PL and SEM analyses. Rietveld refinement analysis was carried out to confirm the structure of the synthesized phosphor. The prepared phosphor shows an intense red emission around 627 nm under excitation by near UV light. The ⁵D₀-⁷F₂ transition intensity of the prepared phosphor is three times higher compared to the commercial (Y,Gd)BO₃:Eu³⁺ red phosphor. The CIE colour coordinates of BaY₂ZnO₅:Eu³⁺ (9mol%) phosphor corresponds to be (0.6169, 0.3742) and it has a high 97.9 % colour purity. The obtained results reveal the utility of BaY₂ZnO₅:Eu³⁺ phosphor as an efficient red component in WLEDs, anti-counterfeiting and fingerprint detection applications.     

The impact of the thermal treatment during ink preparation on the ionomer-supported catalyst interactions in the catalyst layers

Catalyst slurries (inks) were prepared with and without thermal treatment to determine the support/ionomer structures and interactions in the catalyst layer (CL) which impact on membrane electrode performance and durability. The thermal treatment of the ink has a nominal effect on the ionomer/support structure in which the carbon support is non-graphitised. The agglomerate/aggregate structures have a high degree of support/ionomer interface and sufficient macroporosity for water movement in the CL. This improves the membrane electrode assembly (MEA) performance, but also accelerates electrochemical carbon degradation. Thermal treatment of graphitised support-containing inks resulted in increased performance facilitated by a larger support/ionomer interface. Without thermal treatment, the more hydrophobic support would form aggregate structures in which water contact was restricted, limiting proton transfer, isolating catalyst, decreasing performance. The water limited access, would however, prolong stability during accelerates carbon degradation. The electrochemical properties were studied using full and half MEA cells.     

三聚硫氰酸单钠盐的制备及应用研究进展

三聚硫氰酸单钠盐是一种新型的多官能团化精细化学品。介绍了三聚硫氰酸单钠盐的制备方法,以及其在橡胶硫化、橡胶与金属的硫化粘合等领域的应用研究进展。     

Preparation and characterization of calcium phosphate cement with enhanced tissue adhesion for bone defect repair

Anti-washout and tissue adhesion properties are essential for the clinical application of injectable bone materials. In this study, we prepared calcium phosphate cement (CPC) with anti-washout and tissue adhesion properties and attempted to build covalent bonds between CPC and the amino groups in bone tissue under a self-regulating pH system in the CPC (acidic to basic). The results of push-out tests demonstrated that a significant enhancement (from 6.42 ± 0.76 N to 61.5 ± 4.09 N) in tissue adhesion was obtained with the addition of 6% (w/w) oxidized sodium alginate (OSA) in CPC. The FTIR, XRD, anti-washout test, XPS, pH test, and SEM results suggested that the synergistic effect of OSA-citric acid (CA) led to the formation of a three-dimensional gel network structure in the CPC, and the Schiff base reaction between aldehyde and amino groups induced adhesion between CPC and the bone tissue. Further, the addition of less OSA had no significant negative effect on the hydration properties of CPC. Our work aims to promote the development of injectable bone material in clinical applications.     

Immiscible PHB/PBS and PHB/PBSA blends: morphology,phase composition and modelling of elastic modulus

This paper reports the thermal, morphological and mechanical properties of environmentally friendly poly(3-hydroxybutyrate) (PHB)/poly(butylene succinate) (PBS) and PHB/poly[(butylene succinate)-co-(butylene adipate)] (PBSA) blends, prepared by melt mixing. The blends are known to be immiscible, as also confirmed by the thermodynamic analysis here presented. A detailed quantification of the crystalline and amorphous fractions was performed, in order to interpret the mechanical properties of the blends. As expected, the ductility increased with increasing PBS or PBSA amount, but in parallel the decrease in the elastic modulus appeared limited. Surprisingly, the elastic modulus was found properly described by the rule of mixtures in the whole composition range, thus attesting mechanical compatibility between the two blend components. This unusual behavior has been explained as due to co-continuous morphology, present in a wide composition range, but also at the same time as the result of shrinkage occurring during sequential crystallization of the two components, which can lead to physical adhesion between matrix and dispersed phase. For the first time, the elastic moduli of the crystalline and mobile amorphous fractions of PBS and PBSA and of the mobile amorphous fraction of PHB at ambient temperature have been estimated through a mechanical modelling approach. © 2021 The Authors. Polymer International published by John Wiley & Sons Ltd on behalf of Society of Industrial Chemistry.     

Preparation of P(St-NMA) microsphere inks and their application in photonic crystal patterns with brilliant structural colors

Patterned photonic crystals with structural colors on textile substrates have attracted a special attention due to the great advantages in application, which currently become a research hot-spot. This study utilized an ink-jet printing technology to prepare high-quality photonic crystal patterns with structural colors on polyester substrates. The self-assembly temperature of poly(styrene-N-methylol acrylamide) (P(St-NMA)) microspheres set to construct photonic crystals were deeply optimized. Moreover, the structural colors of prepared photonic crystal patterns were characterized and evaluated. When the mass fraction of P(St-NMA) microspheres was 1.0 wt.%, the pH value ranged from 5 to 7, and the surface tension was in the range of 63.79 to 71.20 mN/m, inks could present the best print performance. At 60 °C, prepared P(St-NMA) microsphere inks were good for printing to obtain patterned photonic crystals with regular arrangement and beautiful structural colors. Specifically, photonic crystals with different colors could be constructed by regulating the diameter of microspheres in inks, and prepared structural colors exhibited distinct iridescent phenomenon. The present results could provide a theoretical basis for the industrial realization of patterned photonic crystals by ink-jet printing technology.     

军工船舶发电机用特种漆包线的研制

为提升漆包线产品的技术水平与行业市场竞争力,使产品进入漆包线产品的高端市场,扩大公司漆包线新品种与技术储备,提升公司科研创新和新产品的研发能力,与客户合作开展对军工船舶发电机用特种漆包线的研制。根据特种漆包线的性能要求和关键技术,对其漆膜绝缘材料的选择、产品结构的设计与优化及研制的生产工艺技术进行探讨,研制出的特种漆包线通过对其性能考核,完全满足客户的各项性能指标要求。     

Formulating Pantone colors by unused base inks,formulation software,and a spectrophotometer

Unused base inks that are not going to be used for printing production are considered to be hazardous materials. Their disposal is expensive, and strict environmental regulations should be followed for their disposal. As an alternative, this article describes how spectral data of unused base inks can be gathered and mixed to generate new colors to incorporate them back to print production for small‐volume jobs. In this study, 30 different Pantone colors were selected as target colors. The CIE L*a*b* spectral data of Pantone colors and unused base inks were gathered via a spectrophotometer. A commercial formulation software, based on multiflux theory and CIE L*a*b* color space, was used to formulate ink recipes that contained the base inks. To quantify the performance of ink recipes, they were mixed and printed using an offset printability tester. The CIELAB ΔE*_ab metric, developed by CIE, was used to detect the visual differences between the target Pantone Color and printed colors.