Laser damage resistance of plasma-sprayed alumina and honeycomb skeleton/alumina composite ceramic coatings

Al₂O₃ and honeycomb skeleton-Al₂O₃ composite coatings on Titanium alloy (Ti–6Al–4V) were prepared by atmospheric plasma spraying. A laser ablation experiment on as-sprayed coatings was performed. In this paper, the laser damage resistance, microstructure, phase composition of Al₂O₃ coatings were examined. 3D Dimensional Confocal Microscopy, Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), and Energy Dispersive Spectrometry (EDS) characterized the laser damage morphology, microstructure, phase composition, and element analysis, respectively. The influence of the honeycomb skeleton on the laser ablation damage on as-sprayed coatings was investigated by a comparative analysis of the laser damage morphology with different laser ablation times and gas flow. The results show that the honeycomb skeleton raises thermal conductivity and thermal diffusivity. Moreover, a “tower”-like dendrite was generated during the laser irradiation of the composite coating. The honeycomb skeleton refined the structure, suppressed crack propagation, and reduced the influence of gas flow on cracks. Under the same experimental laser ablation parameters, the laser damage area of the honeycomb skeleton-Al₂O₃ composite coating was smaller than that of the Al₂O₃ coating. It was demonstrated that the laser damage resistance of the honeycomb skeleton-Al₂O₃ composite coating was superior to that of the Al₂O₃ coating.     

Cold sintered,temperature-stable CaSnSiO5-K2MoO4 composite microwave ceramics and its prototype microstrip patch antenna

Dense (1-x)wt%CaSnSiO₅-xwt%K₂MoO₄ (CSSO-KMO) composite ceramics were fabricated by the cold sintering process at 180 °C under 400 MPa for 60 min. X-ray diffraction, Energy dispersive X-ray and Raman spectroscopy confirmed that CSSO and KMO coexisted without intermediate phases. As KMO weight fraction increased, relative permittivity (ε_r) and temperature coefficient of resonant frequency (τ_f) decreased and the microwave quality factor (Q×f, where f is resonant frequency) increased. Near-zero τ_f (-0.5 ppm/°C) was obtained for 65 wt%CSSO-35 wt%KMO with ε_r ～ 9.2 and Q×f ～ 6240 GHz. No chemical reaction between ceramic composites and silver was observed, demonstrating potential for cofiring with Ag-paste. A prototype antenna was fabricated from 65 wt%CSSO-35 wt%KMO composite ceramic with a bandwidth of 144 MHz @ -10 dB, a gain of 5.7 dBi and a total efficiency of 88.4 % at 5.2 GHz, suitable for 5 G mobile communication systems.     

Effect of impact angle on wear behavior of Mo2NiB2–Ni cermets with different Ni content

Herein, the influence of the impact angle and Ni content on the wear behavior of Mo₂NiB₂–Ni cermets was studied using an erodent-carrying slurry comprising artificial seawater and SiO₂ sands. The results reveal that the material loss may be attributed to the wear damage caused by SiO₂ sands because cermets are expected to exhibit good corrosion resistance in artificial seawater. The relative density of cermets markedly influences their resistance to wear damage, and the material loss experienced by cermets with poor relative density is 2–4 times higher than that of cermets with good relative density; this occurs because a higher relative density can markedly enhance the mechanical properties and reduce the defects in the cermets. Moreover, the results indicate that as the impact angle increases from 0° to 60°, the manifestation of the wear mechanism changes from damaging the Ni binder phase (caused by single cutting wear) to damaging both the Mo₂NiB₂ ceramic and Ni binder phases due to the combination of cutting wear and impact wear. The wear damage is dominated by the cutting wear and impact wear from SiO₂ sand at the low and high impact angles, respectively. Furthermore, the severe deterioration of the single ceramic skeleton at high impact angles indicates that the synergistic influence of the Mo₂NiB₂ ceramic and Ni binder phases on enhancing the wear resistance of the cermets intensifies at high impact angles.     

Synthesizing a uniformly spaced array pattern using integral operator for removing progressive phase shift

In this article, an analytical technique is introduced to obtain the excitation coefficients of uniformly spaced linear antenna arrays in order to achieve a desired array factor. By integration of the prescribed array factor, the array factor dependency to the progressive phase shift is eliminated. A new system of linear equations is consequently obtained whose solution represents the excitation coefficients of the array. Some examples are presented to verify the accuracy of the introduced method. The performance of this strategy is compared with those obtained by the other well‐known techniques such as Woodward‐Lawson and Fourier transform. It is shown that the presented method estimates the desired array pattern with a very good precision.     

Nature inspired 21 branches sneezewort/Achillea ptarmica plant growth pattern–shaped antenna for Ku‐band applications

This reported paper presents the design and analysis of wideband nature inspired planar antenna of 46 × 18 × 1.6 mm³ size, designed using FR4 (Flame Retardant) substrate. The antenna patch is delineated from the growth pattern of sneezewort plant with supplementary notion of golden ratio in branching and branch width. The total number of branches in each stage follows the Fibonacci series and the branch width is calculated from the golden ratio concept. Starting from one feed line and two branches, the maximum numbers of branches are increased to 20. There has been significant enhancement in the radiation performance of proposed geometry by increasing the number of branches to 21 and by modifying ground with T‐shaped slot. The antenna covers wide impedance bandwidth of 8.2 to 16.5 GHz by possessing stable radiation characteristics.     

基于船载卫星通信三轴天线的跟踪搜索技术

针对船载卫星通信三轴天线跟踪系统,介绍了船载三轴天线的系统组成,提出了一种基于捷联惯导的船载三轴天线跟踪搜索技术。天线以目标地理角为中心,通过坐标转换将目标地理角转换为天线的目标甲板角,调整AEC三轴使其及时准确地跟随目标甲板角。目前,该方法已经成功应用于多种船载三轴天线。实践表明,该方法能够快速准确地搜索到目标卫星,并实现对目标卫星的稳定跟踪。     

一种用于星载SAR天线的转动控制技术

针对星载合成孔径雷达（SAR）天线要求在超低转速下平稳转动，同时满足小型化轻量化的要求，本文提出一种基于微步距模式的天线转动控制技术，该技术使用两个带PWM电路的全桥驱动器通过微步距方式驱动步进电机。在给出系统架构、微步距控制原理后，进一步提出可靠性设计的具体措施。经测试和环境试验验证，该技术对同类应用具有一定的参考价值。     

A narrow-frame antenna for WWAN/LTE/WiMAX/WLAN mobile phones

In this paper, we present a novel narrow-frame antenna with a size of 75 × 8 × 5.8 mm³ for 5.7 in. mobile phones. The antenna mainly consists of a monopole with four branches that are coupled to a two-branch grounded strip. Our antenna is able to cover more bands than other narrow-frame antennas by excitation of several resonant modes. The improved range of the antenna covers the following eleven bands: LTE700, GSM850, GSM900, DCS, PCS, UMTS, LTE2300, LTE2500, LTE3400 (3400–3800 MHz)/WiMAX3.5 GHz (3400–3650 MHz), WLAN5.2 GHz (5150–5350 MHz) and WLAN5.8 GHz (5725–5875 MHz). Another advantage of the proposed antenna is that it does not need any lumped element to match the antenna. The working principles of the proposed antenna are thoroughly studied. A prototype of the proposed antenna is fabricated and measured, with the results in good agreement with the simulation results.     

Flower‐shaped ultra‐wideband fractal antenna

A flower‐shaped ultra‐wideband fractal antenna is presented. It comprises a fourth iterative flower‐shaped radiator, asymmetrical stub‐loaded feeding line, and coplanar quarter elliptical ground planes. A wide operating band of 12.12 GHz (4.58‐16.7 GHz) for S ₁₁ ≤ ? 10 dB is achieved along with an overall antenna footprint of 15.7 × 11.4 mm². In addition, other desirable characteristics, that is, omnidirectional radiation patterns, peak gain upto 5 dB, and fidelity factor more than 75% are achieved. A good agreement exists between the simulation and measured results. The obtained results illustrate that this antenna has wide operating range and compact dimensions than available structures.     

A high gain wideband circularly polarized antenna with asymmetric metasurface

An asymmetric‐metasurface based wideband circularly polarized (CP) microstrip antenna using a coaxial probe is proposed for L‐band applications. The antenna involves a stacked asymmetric‐metasurface, a radiating rectangular‐patch and a coaxial feed. An asymmetric‐metasurface is designed using rectangular unit cells and smaller size unit cells along one of the diagonal lines. The asymmetric‐metasurface is placed above a radiating rectangular‐patch with support of foam layer to achieve a wideband CP radiation. The measured performance of the prototype antenna achieves an impedance bandwidth (?10 dB return loss bandwidth) of 15.7% (1.58‐1.85 GHz) with CP bandwidth (3‐dB axial ratio) of 13% (1.58‐1.80 GHz) and gain of ≥9 dBic.