Non-Halogenated-Solvent Processed and Additive-Free Tandem Organic Solar Cell with Efficiency Reaching 16.67%

Organic solar cells (OSCs) have recently reached a remarkably high efficiency and become a promising technology for commercial application. However, OSCs with top efficiency are mostly processed by halogenated solvents and with additives that are not environmentally friendly, which hinders large-scale manufacture. In this study, high-performance tandem OSCs, based on polymer donors and two small-molecule acceptors with different bandgaps, are fabricated by solution processing with non-halogenated solvents without additive. Importantly, the two active layers developed from non-halogenated solvents show better phase segregation and charge transport properties, leading to superior performance than halogenated ones. As a result, a tandem OSC with high efficiency of up to 16.67% is obtained, showing unique advantages in future massive production.     

Nitrate Additives Coordinated with Crown Ether Stabilize Lithium Metal Anodes in Carbonate Electrolyte

Lithium metal anodes (LMAs) are promising for next-generation batteries but have poor compatibility with the widely used carbonate-based electrolytes, which is a major reason for their severe dendrite growth and low Coulombic efficiency (CE). A nitrate additive to the electrolyte is an effective solution, but its low solubility in carbonates is a problem that can be solved using a crown ether, as reported. A rubidium nitrate additive coordinated with 18-crown-6 crown ether stabilizes the LMA in a carbonate electrolyte. The coordination promotes the dissolution of NO₃⁻ ions and helps form a dense solid electrolyte interface that is Li₃N-rich which guides uniform Li deposition. In addition, the Rb (18-crown-6)⁺ complexes are adsorbed on the dendrite tips, shielding them from Li deposition on the dendrite tips. A high CE of 97.1% is achieved with a capacity of 1 mAh cm⁻² in a half cell, much higher than when using the additive-free electrolyte (92.2%). Such an additive is very compatible with a nickel-rich ternary cathode at a high voltage, and the assembled full battery with a cathode material loading up to 10 mg cm⁻² shows an average CE of 99.8% over 200 cycles, indicating a potential for practical use.     

Microbial susceptibility of various polymers and evaluation of thermoplastic elastomers with antimicrobial additives

The incursion of microbial growth on polymeric products can deteriorate their performance and lead to the development of undesirable staining and odors. A growing trend in the industry has aimed to reduce microbial populations on high-touch surfaces via the use of antimicrobials to protect material aesthetics and durability or to prevent the spread of pathogenic microorganisms. In this study, a variety of plastic substrates (30 unique polymer compounds), including poly(acrylonitrile-co-butadiene-co-styrene), poly(butylene terephthalate), poly(etherimide), various thermoplastic elastomers (TPEs), poly(carbonates), and poly(amides), were screened for susceptibility to microbial attack using American Society for Testing and Materials (ASTM) G21 (fungi susceptibility), Japanese Industrial Standard (JIS) Z2801, and modified ASTM E1428-15a (bacterial susceptibility) test standards. TPEs were determined to be most susceptible to microbial attack under the appropriate environmental conditions. Subsequent studies assessed the use of an antimicrobial additive, zinc pyrithione (ZPT), for potential efficacy in a variety of TPE blends for diverse target market applications. ZPT proved to be very effective in protecting TPEs, reducing Staphylococcus aureus and Escherichia coli populations by 99.9% or more in JIS Z2801 testing and inhibiting fungal growth (rating = 0) according to the ASTM G21 standard.     

Microstructure and mechanical properties of α/β-Si3N4 composite ceramics with novel ternary additives prepared via spark plasma sintering

In this study, α/β-Si₃N₄ composite ceramics with high hardness and toughness were fabricated by adopting two different novel ternary additives, ZrN–AlN–Al₂O₃/Y₂O₃, and spark plasma sintering at 1550 °C under 40 MPa. The phase composition, microstructure, grain distribution, crack propagation process and mechanical properties of sintered bulk were investigated. Results demonstrated that the sintered α/β-Si₃N₄ composite ceramics with ZrN–AlN–Al₂O₃ contained the most α phase, which resulted in a maximum Vickers hardness of 18.41 ± 0.31 GPa. In the α/β-Si₃N₄ composite ceramics with ZrN–AlN–Y₂O₃ additives, Zr₃AlN MAX-phase and ZrO phase were found and their formation mechanisms were explained. The fracture appearance presented coarser elongated β-Si₃N₄ grains and denser microstructure when 20 wt% TiC particles were mixed into Si₃N₄ matrix, meanwhile, exhibited maximum mean grain diameter of 0.98 ± 0.24 μm. As a result, the compact α/β-Si₃N₄ composite ceramics containing ZrN–AlN–Y₂O₃ additives and TiC particles displayed the optimal bending strength and fracture toughness of 822.63 ± 28.75 MPa and 8.53 ± 0.21 MPa?m^1/2, respectively. Moreover, the synergistic toughening of rod-like β-Si₃N₄ grains and TiC reinforced particles revealed the beneficial effect on the enhanced fracture toughness of Si₃N₄ ceramic matrix.     

Dense and core-rim structured B4C-TiB2 ceramics with Mo-Co-WC additive

B₄C-TiB₂ ceramics (TiB₂ ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B₄C-TiB₂ without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB₂ grains. The interface of the rim between TiB₂ and B₄C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B₄C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B₂ rim around the TiB₂ core may occur as a result of the solid solution and dissolution-precipitation between TiB₂ phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB₂ content increased, alongside the decreased hardness. B₄C-30 vol% TiB₂ specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m^1/2.     

Highly transparent Yb:Y2O3 ceramics obtained by solid-state reaction and combined sintering procedures

(Y_0.87-xLa_0.1Zr_0.03Yb_x)₂O₃ (x?=?0.02, 0.04, 0.05) transparent ceramics were obtained by solid-state reaction and combined sintering procedures with La₂O₃ and ZrO₂ as sintering additives. A method based on two-step intermediate sintering in air followed by vacuum sintering was applied in order to control the densification and grain growth of the samples during the final sintering process. The results indicate that La₂O₃ and ZrO₂ co-additives can improve the microstructure and optical properties of Yb:Y₂O₃ ceramics at relatively low sintering temperature. On the other hand, the addition of Zr⁴⁺ ions leads to the formation of dispersed scattering volumes in the ceramic bodies. Transmittance of 78.8% was measured for the 2.0?at% Yb:Y₂O₃ ceramic sample at the wavelength of 1100?nm. The spectroscopic properties of Yb:Y₂O₃ ceramics were investigated at room temperature. The obtained results show that the absorption cross-section at 978?nm is in the range of 2.08?×?10^–20 to 2.36?×?10^–20 cm², whereas the emission cross-section at 1032?nm is ~1.0?×?10^–20 cm².     

Synergistic effect of binary fluoride sintering additives on the properties of silicon nitride ceramics

A variety of combinations of YF₃ and MgF₂ were used as sintering aids in the fabrication of Si₃N₄ ceramics via gas pressure sintering (GPS). The synergistic effects of YF₃ and MgF₂ on the liquid viscosity, mechanical properties, thermal conductivities, and grain growth kinetics of the Si₃N₄ ceramics were investigated. The results showed that appropriately adjusting the YF₃/MgF₂ ratio could decrease liquid viscosity, reducing the diffusion energy barrier of the solute atom and promoting mass transfer. Meanwhile, the chemical bonding strength in the grain boundary complexions formed by the metal cations also influenced grain boundary migration. Samples doped with 4 mol% YF₃ and 2 mol% MgF₂ achieved the lowest grain growth exponent (n = 2.9) and growth activation energy (Q = 616.7 ± 16.5 kJ mol^?1) as well as the highest thermal conductivity (83 W m^?1 K^?1) and fracture toughness (8.82 ± 0.13 MPa m^1/2).     

Low-temperature hot-press sintering of AlN ceramics with MgO–CaO–Al2O3–SiO2 glass additives for ceramic heater applications

Aluminum nitride (AlN) is used a ceramic heater material for the semiconductor industry. Because extremely high temperatures are required to achieve dense AlN components, sintering aids such as Y₂O₃ are typically added to reduce the sintering temperature and time. To further reduce the sintering temperature, in this study, a low-melting-temperature glass (MgO–CaO–Al₂O₃–SiO₂; MCAS) was used as a sintering additive for AlN. With MCAS addition, fully dense AlN was obtained by hot-press sintering at 1500 °C for 3 h at 30 MPa. The mechanical properties, thermal conductivity, and volume resistance of the sintered AlN–MCAS sample were evaluated and compared with those of a reference sample (AlN prepared with 5 wt% Y2O3 sintering aid sintered at 1750 °C for 8 h at 10 MPa). The thermal conductivity of AlN prepared with 0.5 wt% MCAS was 91.2 W/m?K, which was 84.8 W/m?K lower than that of the reference sample at 25 °C; however, the difference in thermal conductivity between the samples was only 14.2 W/m?K at the ceramic-heater operating temperature of 500 °C. The flexural strength of AlN–MCAS was 550 MPa, which was higher than that of the reference sample (425 MPa); this was attributed to the smaller grain size achieved by low-temperature sintering. The volume resistance of AlN–MCAS was lower than that of the reference sample in the range of 200–400 °C. However, the resistivity of the proposed AlN–MCAS sample was higher than that of the reference sample (500 °C) owing to grain-boundary scattering of phonons. In summary, the proposed sintering strategy produces AlN materials for heater applications with low production cost, while achieving the properties required by the semiconductor industry.     

节能减排的颜料印染与助剂(一)

颜料印染对当前印染行业节能减排,降低能耗很有意义,但要做到对纤维没有亲和力的颜料印染,必需制备润湿性、分散性良好的超细颜料粒子。重点阐述利用各种表面活性剂和助剂制备出一种包覆阴离子的超细粒子的稳定分散液,包括各种润湿剂、分散剂、黏合剂和纤维阳离子改性剂,还概述了相关基础理论。     

Microstructure and mechanical properties of TiC0.7N0.3-HfC cermet tool materials

TiC_0.7N_0.3-HfC cermet tool materials were fabricated by hot-press sintering. Effects of different metal additives (Ni, Co, Ni-Co and Ni-Mo), sintering temperature and holding time on the microstructures and mechanical properties of TiC_0.7N_0.3-HfC cermets were investigated. Results showed that Ni-Mo or Ni-Co as metal additives was better for the mechanical properties of TiC_0.7N_0.3-HfC cermets than only Ni or only Co as the metal additives and Ni-Mo better than Ni-Co. HfC particle dispersion existed in these four cermets and only in the TiC_0.7N_0.3-HfC-Ni-Mo cermet the core-rim structure obviously existed. TiC_0.7N_0.3-HfC-Ni-Mo cermet had significantly smaller grains than the other three cermets because Ni-Mo can significantly refine the grain. With the sintering temperature increasing from 1450?°C to 1650?°C, grains grew gradually; Vickers hardness and flexural strength decreased gradually and the fracture toughness increased firstly and then decreased. With the holding time increasing from 15?min to 60?min, grains grew gradually; Vickers hardness, flexural strength and the fracture toughness increased firstly and then decreased. TiC_0.7N_0.3-HfC-Ni-Mo cermets sintered at 1450?°C with 30?min holding time had the better comprehensive mechanical properties with flexural strength of 1346.41?±?31?MPa, fracture toughness of 8.46?±?0.23?MPa?m^1/2 and Vickers hardness of 22.91?±?0.22?GPa.