Accelerating the decarbonization of carbonaceous gold ore by suspension oxidation roasting towards the improvement of gold leaching efficiency

Eliminating the gold preg-robbing effect of carbonaceous matter in carbonaceous gold ores is crucial for gold leaching. In this study, suspension oxidation roasting was proposed to accelerate the decarbonization of carbonaceous gold ore. The characteristics of oxidation reaction process and gas release were analyzed by TG-DTA-FTIR. The phase transformation and microstructure evolution of samples during roasting were analyzed by XRD, SEM and BET. The results show that the gold preg-robbing effect was eliminated after the gasification of carbonaceous matter, and the CaO generated by decomposition of carbonates can effectively capture the SO₂. After roasting for 75 min at 650 °C in a 20% O₂ atmosphere, the total carbon removal rate reached 99.42%, the distribution of exposed gold increased from 28.85% to 77.10% and the gold leaching efficiency increased from 4.55% to 84.83%. In addition, about 70% sulfur was mainly fixed in the roasted products in the form of sulfate. Therefore, the suspension oxidation roasting process is an efficient and clean pretreatment method for carbonaceous gold ores.     

离子型稀土矿山淋洗及尾水富集试验研究

对浸矿后离子型稀土原地浸矿场采用清水进行淋洗，在184天的清水淋洗过程中，尾水氨氮值从最开始的507mg/L，降低至140mg/L，淋洗尾水pH4.52~3.10。淋洗尾水采用两级反渗透膜分离，既回收有价资源稀土，又能使出水氨氮达标。结果表明，产水氨氮浓度稳定低于15mg/L，对稀土的截留率高于98.25%，浓水中稀土离子平均浓度313.4mg/L，可进一步回收稀土资源。     

载铜树脂处理高含盐氨氮废水的性能

针对高含盐氨氮废水，选择具有不同功能基团的树脂为载体，进行负载Cu2+改性制得载铜树脂并对其处理高含盐氨氮废水的性能进行研究。在筛选出最佳载铜树脂的基础上，研究pH及Na+浓度、树脂投加量、反应时间对载铜树脂处理高含盐氨氮废水效果的影响，通过对吸附氨氮前后的载铜树脂进行SEM和EDS表征分析并构建吸附动力学模型以进一步探究配位吸附的过程。结果表明，Cu2+可与螯合树脂D751稳定结合且在宽pH值下均表现出耐盐性和良好的氨氮吸附效果；在室温(25℃)、pH=11及Na+浓度4 g/L、树脂投加量8 g/L、反应时间60 min的条件下，D751载铜树脂对氨氮的去除率为34.8%。D751载铜树脂吸附氨氮后其表面出现明显的晶状结构物质，该物质可能为铜氨络合物。D751载铜树脂对高含盐氨氮的吸附符合准二级动力学模型。     

Migration and distribution of saline ions in bauxite residue during water leaching

Bauxite residue, a highly saline solid waste produced from digestion of bauxite for alumina production, is hazardous to the environment and restricts vegetation establishment in bauxite residue disposal areas. A novel water leaching process proposed here was used to investigate the dynamic migration and vertical distribution of saline ions in bauxite residue. The results show that water leaching significantly reduced the salinity of bauxite residue, leaching both saline cations Na⁺, K⁺, Ca²⁺ and anions CO^2?₃, SO^2?₄, HCO^?₃. Na⁺ and K⁺ migrated from 40–50 to 20–30 cm of the column, presenting a high migration capacity. The migration capacity of Ca²⁺ was lower and accumulated at 30–40 cm of the column. CO^2?₃ initially distributed at 20–30 cm of the column, subsequently transported to 30–40 cm of the column, and finally returned to 20–30 cm of the column along with evaporation. SO^2?₄ was originally distributed at 40–50 cm, but finally migrated to 20–30 cm of the column. Nevertheless, HCO^?₃ remained at the bottom of the column, and its migratory was less affected by evaporation.     

铋精矿加压氧化氨浸高效分离铜、硫和铋

针对湖南柿竹园铋精矿火法冶炼过程中存在的成本高、低浓度SO₂和散烟排放污染环境、有价金属综合回收率低等问题, 以柿竹园铋精矿为原料, 提出了加压氧化氨浸分离铋与铜、硫的新工艺, 研究了氨水加入量、浸出温度、浸出时间、浸出压力及浸出液固比等因素对铜、硫、铋浸出率的影响。在氨水用量1.8 mL/g_铋精矿、液固比4∶1、釜压2.8 MPa、浸出温度160 ℃、浸出时间5 h、搅拌速度600 r/min的优化工艺条件下, 铜、硫浸出率分别达93.57%和92.87%, 铋不浸出并以氧化铋形态全部入渣, 实现了铜、硫与铋的高效分离。     

福建某低品位金矿新型浸金剂浸金试验

福建某斑岩型金矿品位低、规模大,金主要以自然金形式存在,可见金的粒度较粗,为高效利用该低品位金矿,开展新型浸金剂金蝉全泥浸出试验和柱浸试验,结果表明：全泥浸出在磨矿细度为-0.074 mm占80%、矿浆浓度25%、加石灰调pH 值11.0左右、初始金蝉浓度为500 mg/L和过程中控制金蝉浓度不小于300 mg/L条件下浸出20 h,金的浸出率为93.43%,金蝉耗量为1.02 kg/t；柱浸在矿石粒度为-30 mm条件下喷淋浸出23天,金累计浸出率和金蝉累计耗量分别为86.54%和1.22 kg/t。     

湿法炼锌酸浸渣常规干燥实验研究

本文以湿法炼锌酸性浸出渣为研究对象,实验研究干燥温度、物料量、干燥时间对酸浸渣相对脱水率的影响,综合考虑干燥工艺的时效性、经济效益以及工艺效率,控制物料量为50g、干燥温度为90℃、干燥时间为80min时,酸浸渣相对脱水率可达到98.32%。实验研究对促进酸浸渣中有价金属的资源综合利用、改善环境等具有重要的指导意义。     

云南镇源难处理金精矿工艺矿物学研究

利用X射线衍射、X射线荧光光谱（XRF）、X射线能谱分析（EDX）和矿物解离分析（MLA）等检测手段对云南镇源难处理金精矿的化学组成、矿物组成、硫化物特征以及金的分布情况进行了详细的工艺矿物学研究。结果显示：该金矿以硫化矿、碳酸盐和硅酸盐类矿物为主，含有3.18%的有机碳和2.37%的无机碳。通过金的诊断浸出发现96.16%的金被硫化物包裹，少量金以单体形式存在。通过对主要载金矿物黄铁矿、辉锑矿和毒砂的粒度、包裹及裸露情况进行分析，得出大部分硫化矿以解离单体的形式存在，少部分与其他矿物共生。根据MLA测试及金的诊断浸出，认为大部分金被硫化矿完全包裹，处理该矿石时应先进行硫化物包裹层的氧化处理，再进行金矿的浸出。     

多级深度还原法制备Ti6Al4V合金粉体的基础研究

目前Ti6Al4V合金粉体的生产方法主要有雾化法、机械合金法和氢化脱氢法,它们都以Kroll法生产海绵钛为基础。使用钛的氧化物作为原料的熔盐电解法和金属热还原法仍处于研究阶段。本文依据变价金属Ti和V的氧化物在还原过程中逐级还原的特性,提出使用金属氧化物(TiO₂, V₂O₅)作为原料的多级深度还原法制备Ti6Al4V合金粉体的新思路。首先计算了TiO₂-V₂O₅-Mg-Ca体系的吉布斯自由能变,结果表明先进行镁热自蔓延反应,后进行钙热深度还原反应制备Ti6Al4V合金粉体在热力学上具备可行性。然后通过实验进行了的验证。镁热自蔓延反应产物酸浸后除去MgO可得到氧含量为15.84%的多孔Ti-Al-V-O前驱体。配入金属Ca后进行深度脱氧可得到低氧Ti6Al4V合金粉体(Al: 6.2wt.%, V: 3.64wt.%, O: 0.24wt.%, Mg: 0.01wt.%, Ca: < 0.01wt.%)。     

Combining molybdenum carbide with ceria overlayers to boost Mo/CeO2 catalyzed ammonia synthesis

The design of an efficient non-noble metal catalyst is of burgeoning interest for ammonia synthesis. Herein, we report a Mo₂C/CeO₂ catalyst that is superior in ammonia synthesis activity. In this catalyst, molybdenum carbide coexisted with the ceria overlayers which is from the ceria support as the strong metal–support interaction. There is a high proportion of low-valent Mo species, as well as high concentration of Ce³⁺ and surface oxygen species. The presence of Mo₂C and CeO₂ overlayers not only leads to enhancement of hydrogen and nitrogen adsorption, but also facilitates the desorption and exchange of adsorbed species with the gaseous reagents. Compared with the Mo/CeO₂ catalyst prepared without carbonization, the Mo₂C/CeO₂ catalyst is more than sevenfold higher in ammonia synthesis rate. This work not only presents an explicit example of designing Mo-based catalyst that is highly efficient for ammonia synthesis by tuning the adsorption and desorption properties of the reactant gases, but opens a perspective for other elements in ammonia synthesis.