A Ti3C2Tx-carbon black-acrylic epoxy coating for 304SS bipolar plates with enhanced corrosion resistant and conductivity

A conducting and anticorrosive coating is crucial for the application of metal bipolar plates (BP) in proton exchange membrane fuel cell (PEMFC). In this work, a Ti₃C₂T_x (T)-carbon black (C)-acrylic epoxy (AE) coating is prepared on 304 stainless steel (SS) with enhanced corrosion resistance and conductivity. The corrosion resistance of the T-C-AE coating is investigated in a 0.5 M H₂SO₄ solution as compared to the AE, T, and T-AE coatings. The T-C-AE coated 304SS exhibits the strongest corrosion resistance with the most positive corrosion potential and the lowest corrosion current density of 0.00673 μA cm^?2 in all the samples, while retaining intact and compact surface morphology with the lowest metal ion dissolution even after immersed for 720 h. The addition of Ti₃C₂T_x and carbon black into the AE matrix greatly decreases interfacial contact resistance (ICR), and the T-C-AE coating achieves a low ICR of 15.5 mΩ cm^?2 under 140 N cm^?2 compaction force. The excellent anticorrosion performance is mainly attributed to the physical barrier and the cathodic protection provided by the stacked Ti₃C₂T_x (MXene) nanosheets in the T-C-AE coating. This eco-friendly, conducting, and anticorrosive T-C-AE coating has a good application prospect on SS BP of PEMFC.     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

Sustainable phenolic thermosets coatings derived from urushiol

The over-exploitation of finite fossil resources and/or the increased environmental and sustainable awareness inspire scientists and technologists to search for inexpensive alternatives from renewable chemicals. Phenol formaldehyde (PF) resins, the oldest type of synthetic polymers with good mechanical properties and heat resistance, are widely used in the production of coatings, laminates, molding compositions, and glues. Here, biobased urushiol-derived PF resins were synthesized from the alkali-catalyzed reaction between urushiol and formaldehyde. The chemical compositions and molecular structures of resole resins were characterized by carbon-13 nuclear magnetic resonance and Fourier transform infrared spectroscopy, and their curing behaviors were studied by differential scanning calorimetry. The as-prepared urushiol-derived resole resins had methylol (Ph−CH₂OH), ortho- and para-hemiformal groups (Ph−CH₂OCH₂OH), and the para−para/ortho−para/ortho−ortho links of methylene groups (Ph−CH₂−Ph), whereas the resole resins had low curing temperatures at about 100–113°C. Additionally, given the long side alkyl group moiety on the aromatic rings of urushiol, the films of cured urushiol-derived resole resins had low glass transition temperatures of 132 ± 2°C. Furthermore, the as-prepared urushiol-derived coatings exhibited excellent physical and mechanical properties.     

Development of a difunctional oxirane and multifunctional acrylate interpenetrating polymer network composite system with antimicrobial properties

This research continued the development of a difunctional Oxirane and multifunctional Acrylate interpenetrating polymer network composite System (OASys) with antimicrobial properties. The effects of 4-Isopropyl-4′-methyldiphenyliodonium tetrakis (pentafluorophenyl) borate (Borate), hexamethylene diamine (HMDA) and N,N-dimethyl p-toluidine (DMPT) on OASys (Epalloy 5001:dipentaerythritol hexaacrylate) composite hardness, contact angle, monomer-to-polymer degree of conversion (DoC), mechanical properties, polymerization shrinkage, shrinkage stress, and antimicrobial properties were determined. Bis-GMA:TEGDMA composites were used as the control. OASys composites with 9 wt% Borate and 0.5 wt% DMPT or 1.5 wt% HMDA had comparable hardness, DoC's and polymerization shrinkages to controls, but had lower contact angles and mechanical properties. Additionally, OASys composites with 1.5 wt% HMDA had significantly less polymerization stress than controls and demonstrated significant antibacterial activity against Streptococcus mutans and Lactobacillus casei out to 3 months. With lower shrinkage stress and long-term antimicrobial activity, OASys composites look promising for increasing the clinical lifetime of dental composites, but improvements in mechanical properties are needed.     

Multivariate process trajectories for molecular description of MF thermal curing and correlation with hydrolytic stability

During curing of thermosetting resins the technologically relevant properties of binders and coatings develop. However, curing is difficult to monitor due to the multitude of chemical and physical processes taking place. Precise prediction of specific technological properties based on molecular properties is very difficult. In this study, the potential of principal component analysis (PCA) and principal component regression (PCR) in the analysis of Fourier transform infrared (FTIR) spectra is demonstrated using the example of melamine-formaldehyde (MF) resin curing in solid state. FTIR/PCA-based reaction trajectories are used to visualize the influence of temperature on isothermal cure. An FTIR/PCR model for predicting the hydrolysis resistance of cured MF resin from their spectral fingerprints is presented which illustrates the advantages of FTIR/PCR compared to the combination differential scanning calorimetry/isoconversional kinetic analysis. The presented methodology is transferable to the curing reactions of any thermosetting resin and can be applied to model other technologically relevant final properties as well.     

杂化包覆玄武岩鳞片/环氧涂料制备与性能

本文在环氧涂料中添加玄武岩鳞片，提高其防腐蚀性能。针对玄武岩鳞片的团聚问题，通过机械力化学改性工艺，采用正硅酸四乙酯、HY-311型钛酸酯偶联剂、E-44型环氧树脂对玄武岩鳞片进行杂化包覆，结果表明，杂化包覆后玄武岩鳞片的沉降时间从2h提高至96 h。杂化包覆玄武岩鳞片添加量为20%涂层的性能最优，附着力为13.40 MPa，耐盐雾时间为2000 h，在3.5%NaCl溶液中浸泡2000 h后，0.01 Hz的阻抗模值仍然有5.15×109 Ω·cm2。     

Synthesis of a novel DOPO‐based polyphosphoramide with high char yield and its application in flame‐retardant epoxy resins

A novel and highly effective flame retardant (FR), DOPO‐TPMP oligomer, was synthesized by a simple condensation of 4‐(hydroxymethyl)‐2,6,7‐trioxa‐1‐phosphabicyclo[2.2.2]octane‐1‐oxide and phosphorus oxychloride followed by a polycondensation reaction with 6‐(2,5‐dihydroxyphenyl)‐6H‐dibenzo[c,e][1,2]oxaphosphinine‐6‐oxide. The chemical structure of DOPO‐TPMP was well characterized using Fourier transform infrared and NMR spectra. DOPO‐TPMP was used as an additive‐type FR for epoxy resin (EP). The FR properties of the resultant EP composites were investigated by limiting oxygen index (LOI) test, UL‐94 vertical burning test and cone calorimeter measurements. Specifically, the EP composite containing 10.0% DOPO‐TPMP achieved a LOI value of 36.1%, V‐0 rating in the UL‐94 test and a 58% reduction in peak heat release rate. Further mechanism analysis attributed the enhanced flame retardancy to the increased char yield on the addition of DOPO‐TPMP. © 2019 Society of Chemical Industry     

汽车同步器齿环用耐高温结构胶膜的性能研究

同步器齿环与碳纤维耐摩擦材料是通过胶粘剂实现粘接,而胶粘剂耐高温性能的优劣则是决定其使用寿命的决定性因素。本文研究了环氧树脂E-51体系、环氧树脂AG80体系以及基材表面处理工艺对于结构胶膜耐高温性能的影响,采用熔融共混法制备了胶粘剂并以玻璃纤维布为背衬制备了耐高温结构胶膜。采用高低温拉力机对不同体系制备的结构胶膜进行了常温、200℃高温的钢材搭接剪切强度的测试。结果表明,对于E-51体系,提高体系交联密度可显著增大常温剪切强度,但高温剪切强度明显下降;对于四官能度的AG80体系,AG80的用量是影响其高温性能的主要因素,同时基材表面喷砂水洗处理后可显著增大结构胶膜与基材粘接有效面积,进而显著改善高温性能。所制备的结构胶膜较常用胶粘剂使用更加便捷,耐高温性能优良,满足同步器齿环使用要求。     

苯并噁嗪树脂的合成及在形状记忆聚合物中的应用研究进展

苯并噁嗪树脂作为一类新型的热固性树脂，具有分子设计性强、阻燃性能和耐腐蚀性能优异、固化时不需要强酸、无小分子放出等优点，在航空、建筑、电子等领域获得了广泛应用。本文主要介绍了苯并噁嗪单体的合成方法（溶剂法、无溶剂法和悬浮法）、降低苯并噁嗪开环聚合温度的方法（合成具有特殊基团的苯并噁嗪单体、添加催化剂）及苯并噁嗪树脂在形状记忆聚合物中的应用（与其他聚合物混合，纯苯并噁嗪化学改性），对苯并噁嗪形状记忆聚合物目前存在的问题进行了概述并对苯并噁嗪形状记忆聚合物的发展前景做出了展望。     

The activation of furfuryl alcohol polymerization by oxygen and its enhanced mechanical properties

The effect of oxygen and additional oxygen providers on furfuryl alcohol polymerization was investigated through chemical analyses and mechanical evaluation. NMR, UV–vis, Fourier transform infrared, and gas chromatography–mass spectrometry (GC–MS) results suggested that atmospheric oxygen and the further addition of an oxygen source functioned as an activator for the entire network polymerization. Interestingly, the construction of a conjugated structure on the furan linear chain, which is key to three-dimensional cross-linking, also appears to be accelerated in the presence of oxygen. Furthermore, the introduction of oxygen providers into the curing system successfully enhanced the mechanical properties of the cured furan resin.