Investigation of fabrication of gas diffusion substrate for proton exchange membrane fuel cells

The gas diffusion substrate (GDS) is essential in the proton exchange membrane fuel cells. Its fabrication techniques affect the performance significantly and are worthy of investigation. In this study, a manufacturing process of the GDS is proposed to understand the formation process of GDS and promote its structure and performance more pertinently. Different states during the preparation process, raw carbon paper, pre-curing, curing, carbonation, and graphitization, are characterized and measured. Experimental and numerical methods are employed to determine the relationships between microstructure, transport, and mechanical performance variation with the fabricating processes. The results show that its porosity, average pore size, and effective diffusivity decrease first and increase after curing. These parameters after graphitization are lower than that of the carbon paper (CP). The electrical resistivity increases dramatically while pre-curing and decreases gradually after curing, carbonation, and graphitization, and it is much reduced after graphitization. Moreover, mechanical measurement results show that both the picks of tensile strength and flexural modulus occur after curing. Its tensile strength shows little change after graphitization compared to the initial paper's. In contrast, the flexural modulus is improved significantly.     

One-step to prepare high-performance gas diffusion layer (GDL) with three different functional layers for proton exchange membrane fuel cells (PEMFCs)

Gas diffusion layer (GDL) is one of the most important components of fuel cells. In order to improve the fuel cell performance, GDL has developed from single layer to dual layers, and then to multiple layers. However, dual or multi layers in GDL are usually prepared by layer-by-layer methods, which cost too much time, energy, and resources. In this work, we successfully developed a facile one-step method to prepare a GDL with three functional layers by utilizing the different sedimentation rates and filtration rates of short carbon fiber (CF) and carbon nanotube (CNT). The treatment temperature for this GDL is much lower than that of traditional method. The thickness of the GDL can be effectively controlled from as thin as 50 μm to more than 200 μm by simply adjusting the content of CF. The GDL with high flexibility is suitable to develop high performance flexible electronics. The fuel cell with the GDL has the maximum power density 1021 mW cm^?2, which shows 19% improvement comparing to the conventional one. Therefore, this work breaks the traditional concept that GDL for fuel cells only can be prepared by very complex and high-cost procedure.     

综采工作面活性磁化水防尘技术研究

煤矿生产是环境较为封闭的井下作业，具有一定的特殊性，作业空间湿度高、生产环境复杂，其中粉尘是危害最大的因素之一，会对机器和人体造成不同程度的损害。粉尘的危害主要由两方面决定:煤尘能够燃烧，在浓度较高时还会爆炸；粉尘会危害人的身体健康。以平煤股份十矿-320 m水平己四采区东翼下段的己_15-16-24130工作面为研究对象，研究磁化水除尘的方法及原理，通过对比分析优选出活性磁化水添加剂，在该工作面试验后具有良好的除尘效果，大大增加了可见度、降低了空气中悬浮的煤尘。研究对该矿井其他工作面除尘工作具有指导意义。     

Paper mill sludge as a renewable substrate for the production of acetone-butanol-ethanol using Clostridium sporogenes NCIM 2337

In the present study, pre-treated paper mill sludge (PMS) was evaluated extensively as a substrate for production of acetone-butanol-ethanol using Clostridium sporogenes NCIM 2337. The PMS was subjected to three types of pre-treatment methods namely alkali, mechanical, and thermal treatment and was analyzed by SEM. The pre-treatment of PMS by alkali was observed to be more effective over the other pre-treatment methods. The alkali pre-treated sludge was then made to undergo fermentation, which showed the conventional process of acidogenesis followed by solventogenesis. The acetone, butanol, and ethanol concentration for 15% alkali pre-treated PMS was estimated to be maximum.     

Nonreciprocal properties of 1D magnetized plasma photonic crystals with the Fibonacci sequence

In this paper, the nonreciprocal properties of a novel kind of 1D magnetized plasma photonic crystals(MPPCs) with the Fibonacci sequence are investigated. The isolation of the proposed 1D MPPCs is also used to analyze the nonreciprocal properties. Compared to the conventional 1D MPPCs with periodic structure, the nonreciprocal performance can be significantly improved.The effects of several parameters of the proposed 1D MPPCs on the nonreciprocal properties are studied by the transfer matrix method, which includes the incident angle, order of the Fibonacci sequence, plasma frequency, plasma cyclotron frequency and plasma filling factor. The obtained results show that the nonreciprocal propagation properties can be improved by increasing the values of the plasma cyclotron frequency and incident angle, but they will worsen by blindly increasing the order of the Fibonacci sequence, plasma frequency and filling factor of plasma.The peaks of transmittance also are obviously reduced. In addition, the value of isolation will increase with increasing the incident angle, order of Fibonacci sequence, plasma frequency and plasma filling factor. However, when the plasma cyclotron frequency is increased, the value of isolation will be increased at lower frequencies, but is almost unchanged at higher frequencies.     

Preceramic paper-derived Ti3Al(Si)C2-based composites obtained by spark plasma sintering

The paper describes the structure and properties of preceramic paper-derived Ti₃Al(Si)C₂-based composites fabricated by spark plasma sintering. The effect of sintering temperature and pressure on microstructure and mechanical properties of the composites was studied. The microstructure and phase composition were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. It was found that at 1150 °C the sintering of materials with the MAX-phase content above 84 vol% leads to nearly dense composites. The partial decomposition of the Ti₃Al(Si)C₂ phase becomes stronger with the temperature increase from 1150 to 1350 °C. In this case, composite materials with more than 20 vol% of TiC were obtained. The paper-derived Ti₃Al(Si)C₂-based composites with the flexural strength > 900 MPa and fracture toughness of >5 MPa m^1/2 were sintered at 1150 °C. The high values of flexural strength were attributed to fine microstructure and strengthening effect by secondary TiC and Al₂O₃ phases. The flexural strength and fracture toughness decrease with increase of the sintering temperature that is caused by phase composition and porosity of the composites. The hardness of composites increases from ~9.7 GPa (at 1150 °C) to ~11.2 GPa (at 1350 °C) due to higher content of TiC and Al₂O₃ phases.     

Modification of exposure conditions by the magnetic field configuration in helicon antenna-excited helium plasma

Modification of exposure conditions downstream in the diffusion chamber has been performed in helicon antenna-excited helium plasma by adjusting the magnetic field(intensity and geometry).In the inductively coupled mode(H mode), a reduction in ion and heat fluxes is found with increasing magnetic field intensity, which is further explained by the more highly magnetized ions off-axis around the last magnetic field lines(LMFL). However, in helicon wave mode(W mode), the increase in magnetic field intensity can dramatically increase the ion and heat fluxes.Moreover, the effect of LMFL geometry on exposure conditions is investigated. In H mode with contracting LMFL, off-axis peaks of both plasma density and electron temperature profiles shift radially inwards, bringing about a beam with better radial uniformity and higher ion and heat fluxes. In W mode, although higher ion and heat fluxes can be achieved with suppressed plasma cross-field diffusion under converging LMFL, the poor radial uniformity and a small beam diameter will limit the size of samples suitable for plasma irradiation experiments.     

Moulded pulp products manufacturing with thermoforming

For an effective optimization of pulp thermoforming and of the moulded pulp products manufactured by this process, a full understanding of the process physics combined with full knowledge of the pressing equipment is necessary. For this reason, in this Addendum, we clarify how the process parameters “Holding time,” “Vacuum time,” “Cycle time,” and “Temperature” were interpreted and subsequently defined for the analysis of the process and product‐related outputs of the thermoforming experiments.     

Controllable electrodeposition synthesis of Pd/TMxOy-rGO/CFP composite electrode for highly efficient methanol electro-oxidation

A novel and high-efficiency Pd/TM_xO_y-rGO/CFP (TM_xO_y = Co₃O₄, Mn₃O₄, Ni(OH)₂) electrocatalyst for directly integrated membrane electrode was synthesized by controllable cyclic voltammetry electrodeposition combined with hydrothermal process. The results showed excellent performance towards methanol oxidation reduction. The Pd/Co₃O₄-rGO/CFP as-prepared catalyst has the best electrocatalytic activity, and mass activity is 5181 mA·mg⁻¹_Pd, which is about 40 times and 4.3 times that of the commercial Pd/C and Pt/C catalyst (JM). It can be attributed that the small size of Pd nanoparticle, uniformity of distribution, and the synergistic interaction between transition metal oxide on the support surface and Pd nanoparticles. The prepared Pd/TM_xO_y-rGO/CFP composite electrode is a promising catalyst for integrated membrane electrode assembly of proton exchange membrane fuel cells in the future.     

七层熔融共挤出石头纸在昆钢的工业化实践

通过制备印刷层、遮盖层、发泡层、增强层母料,再将上述各挤入层的熔融胶状物通过同一模头挤出发泡,经常规三辊压光、冷却、牵引、收卷,即得到七层熔融共挤出石头纸。采用该方法制备的石头纸,挺度好、印刷适应性好,比重低,不透明度高、平滑度好、厚度均匀,各项性能指标符合GB/T22806-2008"白卡纸"的性能指标要求,可用于印制美术印刷品、卡片、名片、包装纸盒等。该制备方法在云南昆钢石头纸环保材料有限得到工业化实践。