Machine learning algorithm selection for windage alteration fault diagnosis of mine ventilation system

Machine learning algorithms have been widely used in mine fault diagnosis. The correct selection of the suitable algorithms is the key factor that affects the fault diagnosis. However, the impact of machine learning algorithms on the prediction performance of mine fault diagnosis models has not been fully evaluated. In this study, the windage alteration faults (WAFs) diagnosis models, which are based on K-nearest neighbor algorithm (KNN), multi-layer perceptron (MLP), support vector machine (SVM), and decision tree (DT), are constructed. Furthermore, the applicability of these four algorithms in the WAFs diagnosis is explored by a T-type ventilation network simulation experiment and the field empirical application research of Jinchuan No. 2 mine. The accuracy of the fault location diagnosis for the four models in both networks was 100%. In the simulation experiment, the mean absolute percentage error (MAPE) between the predicted values and the real values of the fault volume of the four models was 0.59%, 97.26%, 123.61%, and 8.78%, respectively. The MAPE for the field empirical application was 3.94%, 52.40%, 25.25%, and 7.15%, respectively. The results of the comprehensive evaluation of the fault location and fault volume diagnosis tests showed that the KNN model is the most suitable algorithm for the WAFs diagnosis, whereas the prediction performance of the DT model was the second-best. This study realizes the intelligent diagnosis of WAFs, and provides technical support for the realization of intelligent ventilation.     

Experimental study on mitigating wind erosion of calcareous desert sand using spray method for microbially induced calcium carbonate precipitation

Wind erosion is one of the significant natural calamities worldwide, which degrades around one-third of global land. The eroded and suspended soil particles in the environment may cause health hazards, i.e. allergies and respiratory diseases, due to the presence of harmful contaminants, bacteria, and pollens. The present study evaluates the feasibility of microbially induced calcium carbonate precipitation (MICP) technique to mitigate wind-induced erosion of calcareous desert sand (Thar desert of Rajasthan province in India). The temperature during biotreatment was kept at 36 °C to stimulate the average temperature of the Thar desert. The spray method was used for bioaugmentation of Sporosarcina (S.) pasteurii and further treatment using chemical solutions. The chemical solution of 0.25 pore volume was sprayed continuously up to 5 d, 10 d, 15 d, and 20 d, using two different concentration ratios of urea and calcium chloride dihydrate viz 2:1 and 1:1. The biotreated samples were subjected to erosion testing (in the wind tunnel) at different wind speeds of 10 m/s, 20 m/s, and 30 m/s. The unconfined compressive strength of the biocemented crust was measured using a pocket penetrometer. The variation in calcite precipitation and microstructure (including the presence of crystalline minerals) of untreated as well as biotreated sand samples were determined through calcimeter, scanning electron microscope (SEM), and energy-dispersive X-ray spectroscope (EDX). The results demonstrated that the erosion of untreated sand increases with an increase in wind speeds. When compared to untreated sand, a lower erosion was observed in all biocemented sand samples, irrespective of treatment condition and wind speed. It was observed that the sample treated with 1:1 cementation solution for up to 5 d, was found to effectively resist erosion at a wind speed of 10 m/s. Moreover, a significant erosion resistance was ascertained in 15 d and 20 d treated samples at higher wind speeds. The calcite content percentage, thickness of crust, bulk density, and surface strength of biocemented sand were enhanced with the increase in treatment duration. The 1:1 concentration ratio of cementation solution was found effective in improving crust thickness and surface strength as compared to 2:1 concentration ratio of cementation solution. The calcite crystals formation was observed in SEM analysis and calcium peaks were observed in EDX analysis for biotreated sand.     

Effect of different control strategies on rapid cold start-up of a 30-cell proton exchange membrane fuel cell stack

Many places experience extreme temperatures below −30 °C, which is a great challenge for the fuel cell vehicle (FCV). The aim of this study is to optimize the strategy to achieve rapid cold start-up of the 30-cell stack at different temperature conditions. The test shows that the stack rapidly starts within 30 s at an ambient temperature of −20 °C. Turning on the coolant at −25 °C show stability of the cell voltage at both ends due to the end-plate heating, however, voltage of intermediate cells fluctuates sharply, and successful start-up is completed after 60 s. The cold start strategy changes to load-voltage cooperative control mode when the ambient temperature reduced to −30 °C, the voltage of multiple cells in the middle of the stack fluctuate more drastic, and start-up takes 113 s. The performance and consistency of the stack did not decay after 20 cold start-up experiments, which indicates that our control strategies effectively avoided irreversible damage to the stack caused by freeze-thaw process.     

加氢反应器头盖密封质量控制探讨

加氢反应器是加氢装置的重要组成部分,反应器头盖因工况复杂,导致密封难度较大,密封不严,会导致整个装置不能正常运转。为此,就其头盖拆装及密封问题进行探讨,提出有效的质量控制措施。     

Compound fault-tolerant attitude control for hypersonic vehicle with reaction control systems in reentry phase

In this paper, a novel compound fault-tolerant attitude control (FTC) scheme is proposed for reentry hypersonic vehicles with aerodynamic surfaces and reaction control systems (RCS) in the presence of parameter uncertainties, external disturbances and aerodynamic surfaces faults. Aerodynamic surfaces work as the primary actuators and RCS serve as auxiliary actuators. When aerodynamic surfaces cannot provide the required attitude control torque due to low dynamic pressure or faults, RCS are activated to assist aerodynamic surfaces to generate the residual torque. A nonlinear disturbance observer-based sliding mode controller is designed to calculate the required attitude control torque which can handle the parametric uncertainties and external disturbances together. The quadratic programming method is applied to obtain the optimal aerodynamic surfaces deflections from the required control torque. An innovative fuzzy rule-based decision-making system is design to solve the RCS control allocation problem, which is conceptually easy to understand and computationally efficiently compared with existing approaches. Based on quantized control theory, the closed-loop control system stability is rigorously analyzed. Simulation results are given to demonstrate the effectiveness and efficiency of developed FTC scheme.     

On the theory of economic MPC: ELOC and approximate infinite horizon EMPC

In recent years, the notion of Economic Model Predictive Control (EMPC) has gained significant interest. Despite a marked improvement in economic performance, it has been shown that this performance will degrade substantially if implemented with a horizon that is not sufficiently large. In the current effort, it is shown that if applied to a particular reaction process, EMPC performance will abruptly collapse at a critical horizon size. To alleviate this issue, we develop an Infinite Horizon EMPC (IH-EMPC) formulation. While this IH-EMPC problem is computationally intractable, it does lead to an approximation of the optimal policy. The resulting Approximate IH-EMPC (AIH-EMPC) is identical to the original finite horizon EMPC, but includes a final cost term that represents the objective function from the finite horizon to infinity. With two example systems, a chemical reactor and a power system with energy storage, it is shown that the AIH-EMPC policy is virtually insensitive to its computational horizon size.     

定子分段式永磁直线同步电机速度波动抑制方法研究

为了解决定子分段式永磁直线同步电机(PMLSM)存在的因磁阻效应、负载阻力、摩擦力、参数摄动以及动子进出定子时耦合面积变化所造成的控制性能下降的难题,根据动子和定子的耦合状态,提出一种在完全耦合阶段和动子退出定子阶段的分段式控制方法。首先,在动子与定子完全耦合阶段采用改进滑模控制器减小推力波动导致的速度波动,再通过加入扰动观测器降低滑模切换项所带来的抖振现象;在动子退出定子阶段,建立相关电磁参数与动子位置的函数关系,实时补偿由耦合面积变化引起的动子失速,使动子速度在退出时接近给定值。仿真及实验结果表明动定子完全耦合过程中的速度稳态误差为0.005 m/s,收敛时间为0.3 s,动子退出定子阶段的速度波动不超过0.04 m/s,满足定子分段式PMLSM用于长行程自动运输系统对平稳性及快速性的需求。