Characteristic tryptic peptides and gelling properties of porcine skin gelatin affected by thermal action

Thermal action in extraction process had effects on characteristic tryptic peptides identification and gelling properties of porcine gelatin. SDS-PAGE, HPLC-LTQ/Orbitrap high-resolution mass spectrometry, texture analyser and rheometer were used to evaluate collagen depolymerisation degree, characteristic tryptic peptides and gelling properties of gelatins prepared in various thermal actions. Results showed that with increasing temperature and time, depolymerisation degree enlarged, while gel strength, gelling and melting temperature decreased. Mass spectra showed that 47 and 49 common characteristic tryptic peptides were identified in gelatins extracted at 50 °C and 100 °C with various times, respectively. Moreover, 34 common characteristic tryptic peptides were identified in all gelatin samples. Further comparison between this work and our previous investigations yielded 20 common characteristic tryptic peptides, which stably exist in various thermal actions. These common characteristic tryptic peptides may be very helpful for the accurate authentication of porcine gelatin.     

Flash Lamps as Ignition and Initiation Sources of the VS-2 Pyrotechnic Composition

In the present work it is found that the pyrotechnic composition VS-2 can be initiated with flash lamps IFC-500 and EVIS. VS-2 pyrotechnic composition contains 90% of mercury（Ⅱ） 5-hydrazinotetrazolate perchlorate and 10% of optically transparent copolymer of 2-methyl-5-vinyltetrazole and methacrylic acid （PVMT）. We have found that the flash lamps make it possible to initiate combustion of VS-2 composition with its transition to detonation both in cylindrical charges placed in brass caps of 5 mm diameter and 2 mm high， and film charges with 10 mm×80 mm in size and surface weights of 60 mg·cm^-2 and 90 mg·cm^-2， showing ignition delay times 10 μs and 3 μs， respectively. We also measured detonation velocities for VS-2 composition film charges， which were 4375-4505 m·s^-1 （of the charge being surface mass 60 mg·cm^-2） and 4221-4281 m·s^-1 （of the charge being surface mass 90 mg·cm^-2） and their blasting action on the aluminum plate. The depths of the normal shock wave imprints at the charge-barrier interface were 0.6-0.7 mm （for surface mass of the film charges 60 mg·cm^-2） and 1.2-1.3 mm （for surface mass of the film charges 90 mg·cm^-2）.     

Subdivision based isogeometric analysis for geometric flows

We present a new isogeometric analysis (IGA) approach based on extended Loop subdivision scheme for solving various geometric flows defined on subdivision surfaces. The studied flows include the second-order, fourth-order, and sixth-order geometric flows, such as averaged mean curvature flow, constant mean curvature flow, and minimal mean-curvature-variation flow, which are generally derived by minimizing the associate energy functionals with $L^2$-gradient flow respectively. The geometric flows are discretized by means of subdivision based IGA, where the finite element space is formulated by the limit form of the extended Loop subdivision for different initial control meshes. The basis functions, consisting of quartic box-splines corresponding to each subdivided control mesh, are utilized to represent the geometry exactly. For the cases of the evolution of open surfaces with any shape boundary, high-order continuous boundary conditions derived from the mixed variational forms of the geometric flows should be implemented to be consistent with the isogeometric concept. For time discretization, we adopt an adaptive semi-implicit Euler scheme. By several numerical experiments, we study the convergence behaviors of the proposed approach for solving the geometric flows with high-order boundary conditions. Moreover, the numerical results also show the accuracy and efficiency of the proposed method.     

Experimental study on the load bearing behavior of geosynthetic reinforced soil bridge abutments with different facing conditions

This paper presents an experimental study on reduced-scale model tests of geosynthetic reinforced soil (GRS) bridge abutments with modular block facing, full-height panel facing, and geosynthetic wrapped facing to investigate the influence of facing conditions on the load bearing behavior. The GRS abutment models were constructed using sand backfill and geogrid reinforcement. Test results indicate that footing settlements and facing displacements under the same applied vertical stress generally increase from full-height panel facing abutment, to modular block facing abutment, to geosynthetic wrapped facing abutment. Measured incremental vertical and lateral soil stresses for the two GRS abutments with flexible facing are generally similar, while the GRS abutment with rigid facing has larger stresses. For the GRS abutments with flexible facing, maximum reinforcement tensile strain in each layer typically occurs under the footing for the upper reinforcement layers and near the facing connections for the lower layers. For the full-height panel facing abutment, maximum reinforcement tensile strains generally occur near the facing connections.     

Construction and analysis of photovoltaic directly coupled conditions in PEM electrolyzer

The Markov model and the PEM electrolyzer system model for directly coupled photovoltaic are combined to construct an efficient and reliable working condition that fits the fluctuation characteristics of solar energy. The working condition is designed through genetic algorithm so that the average coupling efficiency of the system can reach 98.8%. Then, the durability and recovery test are conducted on the basis of the constructed conditions. It is found that the attenuation rate at the current density of 1A/cm² under the photovoltaic fluctuating condition reached 7.8mV/h, which is twice that under the constant current condition. The charge transfer impedance (R_ct) is the main factor leading to the degradation. It is proved by the recovery experiment that the increase of R_ct is related to the pollution of metal ions. After pickling to remove some metal ions, R_ct can be significantly reduced by 46.8% and 65.2%, respectively. After the durability test, the voltammetric charges under the photovoltaic fluctuating condition and the constant current condition are reduced by 48.3% and 19.1% It indicates that the photovoltaic fluctuation condition will accelerate the attenuation of the effective reaction area of MEA, which is irreversible even after pickling. It can be observed from the SEM images that the catalyst layer of MEA has more obvious peeling under the photovoltaic fluctuation condition, which is not conducive to material transmission and destroys the transmission channel of ions and electrons. This result can provide a reliable reference for the coupling design of PEM electrolyzer and renewable energy in the future.     

基于音频特征的工程车辆工况识别研究

高效率地使用工程车辆是工程项目管理中节约成本的有效方法，无人监管环境下工程车辆的工况识别，是实现工程车辆高效率使用的有效手段。目前以GPS等技术为核心的车辆智能管理系统未对工程车辆进行工况识别，提出一种基于GRU循环神经网络的工程车辆工况识别方法，通过对工程车辆在不同工况下产生的音频信号进行分析，从中提取Mel倒谱系数作为主要特征，构建GRU循环神经网络模型进行训练和识别。实验结果表明，该方法可以实现对工程车辆工况的有效识别。     

多堆厂址始发事件分析探讨

多堆厂址一级概率安全评价（PSA）研究中，机组数目的增加使得建模工作量剧增，给整个核电厂的风险评估带来困难。结合已有基础，本文研究了多堆厂址始发事件分析的筛选方法，提出利用堆芯损伤频率（CDF）上下限值评估方法，分析厂址内不同机组数对厂址CDF的影响。结果表明，双机组厂址适合优先进行具体分析。针对双机组核电站，对多堆厂址内各始发事件进行筛选。结果表明，丧失厂外电、丧失热阱等事件适合建模分析，并对其他筛选结果给出后续分析建议，为多堆厂址一级PSA后续事故序列建模工作提供了重要基础。     

改进的CAGAN在虚拟试衣中的应用

针对CAGAN（Conditional Analogy GAN）换衣后效果模糊，在目标衣服与原始衣服长短不一致时效果一般，相对目标衣服保留过少的细节等问题做了相关研究并对CAGAN进行了改进，提出了新的虚拟试衣方式。经过改进的CAGAN生成一个粗糙的结果，由该结果得到目标衣服穿在模特身上改变形状后的mask，接下来利用mask对目标衣服进行变形，综合变形的衣服和第一步的结果便得到最终的试衣图像。实验结果表明，该方法解决了前面存在的问题，而且取得了非常好的效果。     

Intrinsic Defect Limit to the Growth of Orthorhombic HfO2 and (Hf,Zr)O2 with Strong Ferroelectricity: First-Principles Insights

It is believed that promoting the fraction of ferroelectric orthorhombic phase (o-phase) through O-poor growth conditions can increase the spontaneous polarization of HfO₂ and (Hf,Zr)O₂ thin films. However, the first-principles calculations show that the growth may be limited by the easy formation of point defects in the orthorhombic and tetragonal phases of HfO₂, ZrO₂, and (Hf,Zr)O₂. Their dominant defects, O interstitial (O_i) under O-rich conditions and O vacancy (V_O) under O-poor condition, have low formation energies and quite high density (10¹⁶–10¹⁹ cm⁻³ for 800–1400 K growth temperature). Especially, O_i has negative formation energy in tetragonal HfO₂ under O-rich condition, causing non-stoichiometry and limiting the crystalline-seed formation during o-phase growth. High-density defects can cause disordering of dipole moments and increase leakage current, both diminishing the polarization. These results explain the experimental puzzle that the measured polarization is much lower than the ideal value even in O-poor thin films and highlight that controlling defects is as important as promoting the o-phase fraction for enhancing ferroelectricity. The O-intermediate condition (average of O-rich and O-poor conditions) and low growth temperature are proposed for fabricating HfO₂ and (Hf,Zr)O₂ with fewer defects, lower leakage current, and stronger ferroelectricity, which challenges the belief that O-poor condition is optimal.     

极限工况下的管网“互联互通”改进方案

在全国天然气管道“主干互联、区域成网”(以下简称“互联互通”)基础格局逐渐形成的背景下,天然气管网规模日益扩大、管道分支和气源增加,并且分布不集中、输送方向可变,使得输气方案更加灵活,可以更好地解决某些地域的供气紧张问题;但受现有站场和设备的限制,暂不能满足某些多线组合极限工况,使得“互联互通”的初衷难以全部实现。为了使得现有的各输气干线在实现“互联互通”之后可以满足更多的多线组合工况,在分析“互联互通”背景下M管网工况变化的基础上,研发了可以进行水力仿真和压气站方案制订的计算软件,并对3种极限工况下的不同输气量情况进行了可行性试算,进而基于试算结果提出了相应的管网改进建议。研究结果表明:(1)经验证,软件计算误差满足要求;(2)在M管道某处增设压气站或在某些输气站场配置压缩机组;(3) M管网改进调整后,可以完成大部分的多线组合极限工况,真正实现“互联互通”的输气方案。结论认为,该研究成果有助于推进全国天然气管网早日实现“互联互通”。