An analytical model for gas leakage through contact interface in proton exchange membrane fuel cells

Sealing performance between two contacting surfaces is of significant importance to stable operation of proton exchange membrane (PEM) fuel cells. In this work, an analytical micro-scale approach is first established to predict the gas leakage in fuel cells. Gas pressure and uneven pressure distribution at the interface are also included in the model. At first, the micro tortuous leakage path at the interface is constructed by introducing contact modelling and fractal porous structure theory. In order to obtain the leakage at the entire surface, contact pressure distribution is predicted based on bonded elastic layer model. The gas leakage through the discontinuous interface can be obtained with consideration of convection and diffusion. Then, experiments are conducted to validate the numerical model, and good agreement is obtained between them. Finally, influences of surface topology, gasket compression and gasket width on leakage are studied based on the model. The results show that gas leakage would be greatly amplified when the asperity standard deviation of surface roughness exceeds 1.0 μm. Gaskets with larger width and smaller thickness are beneficial to sealing performance. The model is helpful to understand the gas leakage behavior at the interface and guide the gasket design of fuel cells.     

Investigation of fabrication of gas diffusion substrate for proton exchange membrane fuel cells

The gas diffusion substrate (GDS) is essential in the proton exchange membrane fuel cells. Its fabrication techniques affect the performance significantly and are worthy of investigation. In this study, a manufacturing process of the GDS is proposed to understand the formation process of GDS and promote its structure and performance more pertinently. Different states during the preparation process, raw carbon paper, pre-curing, curing, carbonation, and graphitization, are characterized and measured. Experimental and numerical methods are employed to determine the relationships between microstructure, transport, and mechanical performance variation with the fabricating processes. The results show that its porosity, average pore size, and effective diffusivity decrease first and increase after curing. These parameters after graphitization are lower than that of the carbon paper (CP). The electrical resistivity increases dramatically while pre-curing and decreases gradually after curing, carbonation, and graphitization, and it is much reduced after graphitization. Moreover, mechanical measurement results show that both the picks of tensile strength and flexural modulus occur after curing. Its tensile strength shows little change after graphitization compared to the initial paper's. In contrast, the flexural modulus is improved significantly.     

Facile preparation of SnS2 nanoflowers and nanoplates for the application of high-performance hybrid supercapacitors

In this work, the SnS₂ nanoflowers (SnS₂ NFs) were solvothermally prepared in the solvent of ethanol, while SnS₂ nanoplates (SnS₂ NPs) were obtained through the identical conditions except for the solvent of water. The flowers were assembled with numerous nanosheets with very thin thickness, and the NPs exhibited hexagonal shape. When used as the battery-type electrode material for supercapacitors, the SnS₂ NFs delivered a specific capacity of as high as 264.4 C g^?1 at 1 A g^?1, which was higher than the 201.6 C g^?1 of SnS₂ NPs. Furthermore, a hybrid supercapacitor (HSC) was assembled with the SnS₂ as positive electrode and activated carbon (AC) as negative electrode, respectively. The SnS₂ NFs//AC HSC exhibited a high energy density of 28.1 Wh kg^?1 at 904.3 W kg^?1, which was higher than the 24.2 Wh kg^?1 at 844.3 W kg^?1 of SnS₂ NPs//AC HSC. Especially, when the power density was enhanced to the highest value of 8666.8 W kg^?1, the NFs-based device could still hold 20.4 Wh kg^?1. In addition, both HSC devices showed an excellent cycling stability after 5000 cycles at 5 A g^?1. The present method is simple and can be extended to the preparation of other transition metal sulfides (TMSs)-based electrode materials with brilliant electrochemical performance for supercapacitors.     

Combining a new baseboard radiator with a fan coil system for improving heating performance and reduce energy consumption

In the present work, the heating performance of a new system combined with a new modified baseboard radiator and fan coil is investigated. Using longitudinal fins with special geometry and also forced airflow at the end of the system causes that at the lower inlet water temperature compared with the conventional models, higher heat output rate be obtained. The heat output rate of the new modified system is obtained by experimental metrology based on the European Standard No. EN-442. Temperature and velocity distribution in the room space is done by simulation of the modified system in the Flovent software. Computational fluid dynamics (CFD) results are validated against experimental results and there is a good agreement between them. Also, the energy consumption of the system during the winter season is calculated in TRANSYS software. Experimental results show that the heat output rate of a new modified heating system with inlet water temperature in the range of 45–55°C is on average 4.17 times higher compared with the conventional model. CFD simulation also showed that the combined system provides good thermal comfort conditions. Energy consumption of the new system reduced about 13% compared with conventional models.     

Influencer-defaulter mutation-based optimization algorithms for predicting electricity prices

Efficient electricity price forecasting plays a significant role in our society. In this paper, a novel influencer-defaulter mutation (IDM) mutation operator has been proposed. The IDM operator has been combined with six well-known optimization algorithms to create mutated optimization algorithms whose performance has been tested on twenty-four standard benchmark functions. Further, the artificial neural network is integrated with mutated optimization algorithms to solve the electricity price prediction problem. The policymakers can identify appropriate variables based on the predicted prices to help future market planning. The statistical results prove the efficacy of the IDM operator on the recent optimization algorithms.     

高效液相色谱法测定化妆品中依克多因的含量

建立高效液相色谱法测定化妆品中依克多因的分析方法,采用Agilent Poroshell 120 EC-C₁₈色谱柱（100 mm×3.0 mm,2.7μm）分离,以甲醇和p H为3.0的40 mmol/L磷酸二氢钠-10 mmol/L 1-庚烷磺酸钠缓冲溶液梯度洗脱,流速0.8 m L/min,柱温30℃,检测波长210 nm。采用外标法定量测定化妆品中的依克多因含量。结果表明,依克多因在5～800 mg/L的质量浓度范围内呈现良好线性关系,相关系数为0.999 8,方法的检出限和定量限分别为0.3和1.0 mg/L。该方法具有分离效率高、分析时间短、节省溶剂等优点,解决了依克多因在C₁₈色谱柱上保留弱的问题。     

Effect of ligand environment of rare-earth ions on temperature measurement performance of SrAO4:xEu3+ (A = Mo and W) phosphors

Molybdate and tungstate with scheelite-type structure are excellent self-luminescent materials, which can be used as ideal hosts for the doping of rare-earth ions. In this study, a series of Eu³⁺-activated SrAO₄ (A = Mo and W) phosphors were successfully synthesized, and their crystal structures, photoluminescence properties, and temperature measurement performance were analyzed in detail. These phosphors were excited by UV light (291 nm and 247 nm, respectively), with clear energy transfer (ET) (MoO₄^2?→Eu³⁺ or WO₄^2?→Eu³⁺). According to fluorescence intensity ratio (FIR) and Judd–Ofelt (J–O) theory, compared to SrWO₄:0.01Eu³⁺ phosphor, SrMoO₄:0.01Eu³⁺ phosphor exhibited better thermal stability, with relatively low Sa value (maximum values were 5.082 %K^?1 and 20.74 %K^?1, respectively), and their Sr values were not significantly different (maximum values were 0.864 %K^?1 and 0.83 %K^?1, respectively). Sa value was negatively correlated to central asymmetry of Eu³⁺, but the optimal Sr value tended to be more suitable for central asymmetry of Eu³⁺. In addition, Eu³⁺ exhibited stronger central asymmetry as well as covalency of Eu–O bond in SrMoO₄. Results reveal that SrMoO₄:xEu³⁺ and SrWO₄:xEu³⁺ can be used for luminescent thermometers.     

Impact of TiO2 nanoparticles and nanowires on corrosion protection performance of chemically bonded phosphate ceramic coatings

The impact of the addition of TiO₂ nanoparticles and nanowires on the morphology, phase characteristics, contact angle, and electrochemical performance of chemically bonded phosphate ceramic coatings (CBPCs) was investigated. The chemical composition and surface morphology of the TiO₂ nanoparticle and nanowire modified with and without (heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane were characterized. Results indicated that the hydrophobic –CF₂– and –CF₃ groups were successfully introduced into the TiO₂ nanoparticles and nanowires after modification. Corrosion resistance of CBPCs with TiO₂ was evidently improved compared with that without TiO₂. Such improvement was mainly due to the combined effects of low surface energy materials and micro/nano structures. In addition, CBPCs with TiO₂ nanowires exhibited higher hydrophobicity and corrosion resistance than those with TiO₂ nanoparticles because of the special columnar structure of the nanowires.     

非常规气藏储层改造体积评价方法研究

为精确描述非常规气藏压裂后的复杂流动特征及定量评价储层改造体积（SRV），利用自主研发的缝网重构算法“破裂树生长法”建立压后缝网模型，并以此为基础提出了使用拟稳态流动时特定的压力等值线来确定SRV范围的定量评价方法，最后以长宁201井区为例进行了矿场实例分析。该方法根据微地震监测点的位置，重构出微裂缝网的连通关系。在复杂微裂缝网的基础上建立离散裂缝地质模型并进行生产数值模拟，根据数值模拟结果的压力分布精确划定SRV的范围。利用该方法计算出长宁201井区的SRV体积为0.052 1 km3，以该缝网模型的数值模拟产量预测结果符合实际生产规律，方法实用性较好。     

Predictive environmental hydrogen embrittlement on fracture toughness of commercial ferritic steels with hydrogen-modified fracture strain model

In this work, a practical numerical model with few parameters was proposed for the prediction of environmental hydrogen embrittlement. The proposed method adopts hydrogen enhanced plasticity-based mechanism in a fracture strain model to describe hydrogen embrittlement. Fracture toughness degradation of three commercial steels SA372J70, AISI4130 and X80 in high pressure hydrogen environment were investigated. Firstly, governing equations for hydrogen distribution and material damage evolution was established. Hydrogen enhanced localized flow softening effect was coupled within fracture strain dependency on stress triaxiality. Then, the numerical implementation and identification process of model parameters was described. Model parameters of the investigated steels were determined based on experiment results from literatures. Finally, with the calibrated model, fracture toughness reduction of the steels was predicted in a wide range of hydrogen pressure. The prediction results were compared with experimental results. Reasonable accuracy was reached. The proposed method is an attempt to reach balance between physical accurate prediction and engineering practicality. It is promising to provide a simplified numerical tool for the design and fit for service evaluation of hydrogen storage vessels.