Farmers' preferences for adopting on-farm concentration of raw milk: Results from a discrete choice experiment in Germany

Milk concentrates are used in the manufacturing of dairy products such as yogurt and cheese or are processed into milk powder. Processes for the nonthermal separation of water and valuable milk ingredients are becoming increasingly widespread at farm level. The technical barriers to using farm-manufactured milk concentrate in dairies are minimal, hence the suspicion that the practice of on-farm raw milk concentration is still fairly uncommon for economic reasons. This study, therefore, set out to investigate farmers' potential willingness to adopt a raw milk concentration plant. The empirical analysis was based on discrete choice experiments with 75 German dairy farmers to identify preferences and the possible adoption of on-farm raw milk concentration. The results showed that, in particular, farmers who deemed the current milk price to be insufficient viewed on-farm concentration using membrane technology as an option for diversifying their milk sales. We found no indication that adoption would be impeded by a lack of trustworthy information on milk processing technologies or capital.     

Probabilistic learning on manifolds (PLoM) with partition

The probabilistic learning on manifolds (PLoM) introduced in 2016 has solved difficult supervised problems for the “small data” limit where the number N of points in the training set is small. Many extensions have since been proposed, making it possible to deal with increasingly complex cases. However, the performance limit has been observed and explained for applications for which N is very small and for which the dimension of the diffusion-map basis is close to N. For these cases, we propose a novel extension based on the introduction of a partition in independent random vectors. We take advantage of this development to present improvements of the PLoM such as a simplified algorithm for constructing the diffusion-map basis and a new mathematical result for quantifying the concentration of the probability measure in terms of a probability upper bound. The analysis of the efficiency of this extension is presented through two applications.     

Impact of viscous dissipation and Dufour on MHD natural convective flow past an accelerated vertical plate with Hall current

The present research work concentrates on viscous dissipation, Dufour, and heat source on an unsteady magnetohydrodynamics natural convective flow of a viscous, incompressible, and electrically conducting fluid past an exponentially accelerated infinite vertical plate in the existence of a strong magnetic field. The presence of the Hall current induces a secondary flow in the problem. The distinguishing features of viscous dissipation and heat flux produced due to gradient of concentration included in the model along with heat source as they are known to arise in thermal-magnetic polymeric processing. The flow equations are discretized implicitly using the finite difference method and solved using MATLAB fsolve routine. Numerical values of the primary and secondary velocities, temperature, concentration, skin friction, Nusselt number, and Sherwood number are illustrated and presented via graphs and tables for various pertinent parametric values. The Dufour effect was observed to strengthen the velocity and temperature profile in the flow domain. In contrast, due to the impact of viscous dissipation, the local Nusselt number reduces. The study also reveals that the inclusion of the chemical reaction term augments the mass transfer rate and diminishes the heat transfer rate at the plate.     

电商平台产品共同购买网络的影响因素研究

共同购买网络的推荐系统应用越加广泛，仅基于网络内生结构变量研究其共同购买链接的经济意义已有局限，故加入网络口碑这一外生变量，进行更全面的分析。采用了社会网络方法中指数随机图模型进行建模，主要围绕产品销售量、产品入度、差评率和评论数4个方面因素，探究其对共同购买网络中共同购买链接形成的影响。结果显示，销售量、产品入度和评论数对共同购买链接形成的影响呈正比关系，而差评率则会显著地降低产品共同购买的几率。该指数随机图构建出的共同购买网络为在线电商平台管理网络口碑和推荐系统优化设计提供有益参考。     

Preparation of faceted TaN grains by heating Ta-containing oxides in BN crucible with Na

Single-crystal grains of TaN were synthesized by heating Ta₂O₅, FeTa₂O₆, or FeTaO₄ in a BN crucible together with Na metal in an Ar atmosphere at 1100 °C. The BN crucible acted a solid source of nitrogen. Aggregates of columnar ε-TaN single crystals 10–150 μm in size were formed on the inner wall of the BN crucible when either Ta₂O₅ or FeTa₂O₆ was used. On the other hand, platelet-like single crystals of θ-TaN 1–50 μm in size were obtained from FeTaO₄. The results of wavelength-dispersive X-ray spectrometry indicated that the compositions of the ε-TaN and θ-TaN crystals were close to the stoichiometric ideal.     

基于JJG(闽)1086-2018放射治疗CT模拟定位机X射线辐射源的质控分析

整个精确放疗流程最关键、最基础的一个环节就是定位CT扫描精确程度,做好定位CT的质控关乎整个放疗流程的成败。介绍了JJG(闽)1086-2018放射治疗CT模拟定位机X射线辐射源在检定和质控中的流程和方法,从剂量性能要求、图像成像质量和机器机械精度方面对CT模拟定位机的质量控制做了定量的要求。连续8个月的测试结果表明:CT测量值误差在30HU以内,图像均匀性≤5.0HU,空间分辨力7Lp/cm,低对比度分辨力在对比度为1.0%,0.5%,0.3%时分别≤3.0mm,≤5.0mm,≤6.0mm,达到了规程的要求。CT模拟定位机的图像质量和机械精确程度得到了很好的保障,定位CT的剂量准确,影像参数和位置精确度有规可循。     

超精密气体静压系统节流器法向随机微振动研究

以无气腔平面节流器为研究对象,对节流器流固耦合法向随机微振动进行了理论仿真和实验研究。受限于节流器厚度与气膜厚度尺寸的差异和输入初始边界条件,建立了节流器的COMSOL仿真简化模型,对节流器-气膜微流场进行双向流固耦合数值模拟。仿真结果表明,节流器的法向随机微振动幅值关于节流器中心对称,且由中心向边缘逐渐增大;微振动幅值随气体入口流速的增大而增大。实验采用纳米级激光测振仪,依次测量供气压力为0.1,0.2,…,0.5 MPa时尺寸为75 mm×50 mm×14 mm的HEXAGON双环联结型节流器多个不同位置的法向振动,实验结果表明,法向随机微振动幅值分布特性与仿真结果一致,关于节流器中心对称,且由中心向边缘逐渐增大,验证了节流器法向微振动的"跷跷板"振动形式;在0.5 MPa供气压力下,边缘振动幅值超过1 nm。对实验数据进行功率谱密度分析,结果表明不同供气压力下法向随机微振动均在9.4 kHz和10.6 kHz处产生较大功率,可认为与节流器-气膜流固耦合系统的固有频率有关。研究结果有效地揭示了节流器法向随机微振动的特性,为气体静压系统避开随机共振区、优化气体静压系统的设计提供了理论指导。     

Design and optimization of radioisotope sources for betavoltaic batteries

A Monte Carlo source model using PENELOPE was developed to investigate different tritiated metals in order to design a better radioisotope source for betavoltaic batteries. The source model takes into account the self‐absorption of beta particles in the source which is a major factor for an efficient source design. The average beta energy, beta flux, source power output, and source efficiency were estimated for various source thicknesses. The simulated results for titanium tritide with 0° and 90° angular distributions of beta particles were validated with experimental results. The importance of the backscattering effect due to isotropic particle emission was analyzed. The results showed that the normalized average beta energy increases with the source thickness, and it reaches peak energy depending on the density and the specific activity of the source. The beta flux and power output also increase with increasing source thickness. However, the incremental increase in beta flux and power output becomes minimal for higher thicknesses, as the source efficiency decreases significantly at higher thicknesses due to the self‐absorption effect. Thus, a saturation threshold is reached. A low‐density source material such as beryllium tritide provided a higher power output with higher efficiency. A maximum power output of approximately 4 mW/cm³ was obtained for beryllium tritide with SiC. A form factor approach was used to estimate the optimum source thickness. The optimum source thickness was found near the thickness where the peak beta particle average energy occurs.     

Stochastic collocation-based nonlinear analysis of concrete bridges with uncertain parameters

This paper focuses on the stochastic response of concrete bridges considering uncertainty in bearing and abutment stiffness. A multi-span simply supported bridge with concrete girders is selected. A 3D-dimensional model is prepared, and nonlinear response history analyses are performed. For the numerical dynamic simulation, the non-sampling stochastic method based on generalized polynomial chaos (gPC) expansion is utilised. The uncertain parameters include the vertical and shear stiffness of bearings and the lateral stiffness of abutments are presented by the truncated gPC expansions. Furthermore, the system response such as base shear, acceleration, velocity and displacement in different columns is presented by gPC expansion with unknown deterministic coefficients. The stochastic Galerkin projection is employed to calculate a set of deterministic equations. A non-intrusive solution, as a set of collocation points, determines the unknown gPC coefficients of the system response and the results are compared with Monte Carlo simulations. The key advantage of spectral discretization is the combination of the mentioned method with the spatial discretization, e.g. finite element model. This study also emphasises the accuracy in results and time efficiency of the proposed non-sampling method for uncertainty quantification of stochastic systems comparing to sampling procedure (e.g. Monte Carlo simulation).