Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Ambient‐cured polyesteramide‐based anticorrosive coatings from linseed oil—A sustainable resource

Ambient‐cured polyesteramide (APEA) coating resin synthesized from dihydroxy fatty amide obtained from linseed oil, a sustainable resource, and poly(styrene‐co‐maleic anhydride), a bifunctional acid component, was found to exhibit improved physicomechanical and anticorrosive properties. The structural elucidation of APEA resin has been carried out by FTIR, ¹H‐NMR, and ¹³C‐NMR spectroscopies. The physicomechanical and chemical resistance properties were investigated by standard methods. The corrosion resistance performance was evaluated in acid, alkali, and organic solvent. The thermal behavior was studied by TGA technique. A comparative study of these properties of APEA with reported baked polyesteramide (PEA) coatings was carried out. A remarkable improvement in the drying property of APEA was observed. The APEA coatings also showed improved physicomechanical and anticorrosive properties as compared to the baked PEA coatings. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1818–1824, 2005     

Theoretical Investigation of Cubic BaVO<Subscript>3</Subscript> and LaVO<Subscript>3</Subscript> Perovskites via Tran–Blaha-Modified Becke–Johnson Exchange Potential Approach

The full potential linearized augmented plane wave method of density functional theory has been used to investigate the structural, electronic, magnetic and thermoelectric properties of cubic perovskites BaVO₃ and LaVO₃. The ferromagnetic ground state has been found to be stable by comparing the total energies of non-spin-polarized and spin-polarized calculations performed for optimized unit cells. For both compounds, the bond length and tolerance factor are also measured. From the band structures and density of states plots, it is found that both compounds are half-metallic. We found that the presence of V at the octahedral site of these perovskites develops exchange splitting through p-d hybridization, which results in a stable ferromagnetic state. The observed exchange splitting is further clarified from the magnetic moment, charge and spin of the anion and cations. Finally, we also presented the calculated thermoelectric properties of these materials, which show that half-metallic BaVO₃ and LaVO₃ materials are potential contenders for thermoelectric applications.     

Probing the intrinsic optical quality of CVD grown MoS<Subscript>2</Subscript>

Optical emission efficiency of two-dimensional layered transition metal dichalcogenides (TMDs) is one of the most important parameters affecting their optoelectronic performance.The optimization of the growth parameters by chemical vapor deposition (CVD) to achieve optoelectronic-grade quality TMDs is,therefore,highly desirable.Here,we present a systematic photoluminescence (PL) spectroscopic approach to assess the intrinsic optical and crystalline quality of CVD grown MoS2 (CVD MoS2).We propose the use of the intensity ratio between the PL measured in air and vacuum as an effective way to monitor the intrinsic optical quality of CVD MoS2.Low-temperature PL measurements are also used to evaluate the structural defects in MoS2,via defect-associated bound exciton emission,which well correlates with the field-effect carrier mobility of MoS2 grown at different temperatures.This work therefore provides a sensitive,noninvasive method to characterize the optical properties of TMDs,allowing the tuning of the growth parameters for the development of optoelectronic devices.     

A study on the effect of polishing fluid volume in ball end magnetorheological finishing process

Ball end magnetorheological finishing is a unique process that utilizes a magnetically controlled ball of polishing fluid at the tip of the rotating tool to finish workpiece of different materials and shapes. The aim of this research is to study the effect of polishing fluid volume on finishing spot size and the surface finish associated with it. A magnetostatic simulation is done to find the variation of flux density in the working gap and on the workpiece surface. The maximum limit of the polishing fluid volume is selected on the basis of area of threshold magnetic flux density (minimum value required for finishing) region on the workpiece surface. The surface characteristics and the diameter of the finished spot are analyzed by varying the fluid volume. The surface obtained with high fluid volume is poorly finished and has scratch marks as the excess fluid flows out from the working gap and forms a thick ring at the periphery of the tool tip. Contrary to this, if the fluid volume is too less, then it merely rotates over the workpiece surface without causing any finishing action. An optimum range of fluid volume produces a good quality surface finish with constant finished spot size.     

Correction on link relative based approach to CUSUM chart

Link relative-based approach was used in an article (see reference 1) to enhance the performance of the cumulative sum (CUSUM) control chart. This technique involves the use of firstly, the link relative variable to convert the process observations in a relative to the mean form and secondly, optimal constants to define a new variable which is used as the plotting statistic of the link relative CUSUM chart. In this article, it is proven through simulation study that the optimal constants with fixed values, as reported in the aforementioned article, give different results. Instead, if the regression technique is used, then the same results will be obtained.     

Selective determination of urea using urease immobilized on ZnO nanowires

Well-aligned zinc oxide (ZnO) nanowire arrays were fabricated on gold-coated plastic substrates using a low-temperature aqueous chemical growth (ACG) method. The ZnO nanowire arrays with 50–130 nm diameters and ∼1 μm in lengths were used in an enzyme-based urea sensor through immobilization of the enzyme urease that was found to be sensitive to urea concentrations from 0.1 mM to 100 mM. Two linear sensitivity regions were observed when the electrochemical responses (EMF) of the sensors were plotted vs. the logarithmic concentration range of urea from 0.1 mM to 100 mM. The proposed sensor showed a sensitivity of 52.8 mV/decade for 0.1–40 mM urea and a fast response time less than 4 s was achieved with good selectivity, reproducibility and negligible response to common interferents such as ascorbic acid and uric acid, glucose, K⁺ and Na⁺ ions.     

Rice-like CuO nanostructures for sensitive electrochemical sensing of hydrazine

In this work, a low temperature aqueous chemical growth methodology was used for the fabrication of CuO nanostructures. The as-synthesised nanostructures were then elaborately characterised by number of analytical techniques such as scanning electron microscopy (SEM) and X-ray powder diffraction (XRD). The obtained nanostructures were observed to possess interlaced rice-shaped structural features with the length and width of individual rice determined to be in the range of 200–300 nm and 50–100 nm respectively. The unique nanostructures when utilised as electrode material exhibited excellent electro-catalytic potential towards oxidation of hydrazine in alkaline media. The excellent conductive of CuO added by the high surface area of obtained nanorice-like structures enabled development of highly sensitive (3087 µA mM⁻¹ cm⁻²), selective and stable electrochemical sensor for hydrazine. In addition, the successfully application of the developed sensor in spiked tap, bottled and industrial water samples for the detection of hydrazine suggested its feasibility for practical environmental application.

     

Pollen morphological investigations of family Cactaceae and its taxonomic implication by light microscopy and scanning electron microscopy

The family Cactaceae is the diversified group of angiosperm plants whose pollen statistics has been used for taxonomic identification. In this article, we present the pollen morphology of eight species belong to seven taxonomically complex genera of Cactaceae including Astrophytum, Cylindropuntia, Echinocereus, Echinopsis, Mammillaria, Opuntia, and Thelocactus using light and scanning electron microscopy. The pollen grains were acetolyzed, measured, described, and electron photomicrographs were taken. Cactaceae can be characterized by presenting different palynomorphological features including pollen type, sculpturing, polar and equatorial diameter, aperture orientation, exine thickness, P/E ratio, and echini features. Four types of pollen shapes, that is, prolate spheroidal (three species), subprolate (two species), prolate (two species), and oblate spheroidal in Echinocereus reichenbachii were observed. The polar and equatorial diameter observed maximum in O. ficus indica 116.95 and 112.27 μm while minimum in M. compressa 38.42 and 21.05 μm. Pollen of two types, tricolpate in members of subfamily Cactioideae and pantoporate in the Opuntioideae were examined. The fertility percentage has been observed maximum in Opuntia macrocentra (83.84%) and minimum in Opuntia ficus‐indica (57.89%). Exine sculpturing showing great variations such as granulate, reticulate, granulate perforate and micro‐echinate foveolate ornamentation was examined only in Echinopsis eyriesii. A key to species, based on pollen micromorphological attributes, has been constructed for correct identification of complex cactus species.