Optimal Water Allocation of Surface and Ground Water Resources Under Climate Change with WEAP and IWOA Modeling

Water Resources Management - The water evaluation and planning (WEAP) approach and the invasive weed optimization algorithm (IWOA) are herein employed to determine the optimal operating policies in...     

Statistical Optimization for Production of Light Olefins in a Fluidized‐Bed Reactor

The methanol‐to‐olefins reaction (MTO) was studied in a small‐scale fluidized‐bed reactor over synthesized silicoaluminophosphate (SAPO‐34) catalysts. Mesoporous nanocrystalline SAPO‐34 molecular sieves were synthesized hydrothermally by ultrasonic and microwave‐assisted aging processes in the presence of hexadecyltrimethylammonium bromide (CTAB) and tetradecyldimethyl(3‐trimethoxysilylpropyl)ammonium chloride (TPOAC) as surfactant agents. The Box‐Behnken experimental design method was applied to determine the optimum operating parameters of this process conducted in the fluidized‐bed reactor. The optimum conditions in terms of reaction temperature, ratio of inlet gas velocity to minimum fluidizing velocity, and MeOH weight fraction were evaluated.     

ANNM: A New Method for Adding Noise Nodes Which are Used Recently in Anonymization Methods in Social Networks

Wireless Personal Communications - One of the main concerns at the time of production or share of information on social networking sites for scientific research and business analysis is privacy....     

Compressive strength and wear properties of SiC/Al6061 composites reinforced with high contents of SiC fabricated by pressure-assisted infiltration

Pressure-assisted infiltration was used to synthesize SiC/Al 6061 composites containing high weight percentages of SiC. A combination of PEG and glass water was used to fabricate SiC preforms and the effect of the presence of glass water on the microstructure and mechanical properties of the preforms was evaluated by performing compression tests on the preforms. Also, the compressive strength and the hardness of the SiC/Al composites were investigated. The results revealed that the glass water improved the compressive strength of the preforms by about five times. The microstructural characterization of the composites showed that the penetration of the aluminum melt into the preforms was completed and almost no porosity could be seen in the microstructures of the composites. Moreover, the composite containing 75 wt% SiC exhibited the highest compressive strength as well as the maximum hardness. The results of the wear tests showed that increasing the SiC content reduces the wear rate so that the Al-75 wt% SiC composite has a lower wear rate and a lower coefficient of friction than those of Al-67 wt% SiC composite. This indicated higher wear resistance in these composites than the Al alloy due to the formation of a tribological layer on the surface of the composites.     

Formation and wear mechanism of nickel titanium intermetallics during heat treatment of nickel coating on Ti-6Al-4V substrate

In the present work, inter-diffusion of nickel and titanium and formation of Ni-Ti intermetallic compounds on Ti-6Al-4V substrate have been studied. Initially, nickel was electrodeposited on the alloy using a modified Watts bath solution at a current density of 2 A dm^?2 for 1?h. The coated specimens were then heat treated for different durations at 750, 800 and 850 °C under argon atmosphere. The effects of temperature and time on the characteristics, hardness and wear resistance of intermetallic phases were investigated. The results showed that a multilayer structure was formed after heat treatment, an outer layer of residual nickel, an area of intermetallic layers with different compositions followed by a solid solution of Ni-Ti. It was also observed that an increase in time or temperature at first led to the formation of thicker intermetallic layers; however, after passing a critical point, the intermetallic layers seem to dissolve into the substrate. Furthermore, the wear rates of the diffusion treated samples were four times lower compared to Ti-6Al-4V alloy when sliding against AISI 52100 hardened steel.     

Role of Nd-Ni on structural,spectral and dielectric properties of strontium-barium based nano-sized X-type ferrites

The influence of neodymium and nickel substitution on structural and dielectric parameters was investigated in strontium-barium X-type hexagonal ferrites having composition SrBaCu_2?xNi_xNd_yFe_28?yO₄₆ (x = 0, 0.2, 0.4, 0.6, 0.8, 1 and y = 0, 0.02, 0.04, 0.06, 0.08, 0.1). Sol-gel method was employed for synthesizing these hexagonal ferrites. The XRD plots of all studied materials which were annealed at 1250 °C show single phase characteristics. Lattice parameter ‘c’ increased as a consequence of larger radius of rare earth ion (Nd³⁺) as compared to (Fe³⁺), while lattice parameter ‘a’ showed very small variation. The cell volume was obtained in the range 2508.32–2523.75 (ų). The inclusion of Nd-Ni also affected X-ray density, bulk density and porosity. The FTIR spectroscopy indicated the particular absorption peaks of hexagonal ferrites and it was performed in the range of 500–700 cm^?1. On account of Nd-Ni doping, the dielectric constant, dielectric loss and AC-conductivity showed decreasing trend. The occupancy of Nd³⁺ ions at octahedral site impedes the valence alternation of Fe³⁺; therefore there was decrease in dielectric permittivity. Ac conductivity has been decreased from 9.14 to 6.49 (Ω cm)^?1 at frequency of 2.7 GHz. The Cole-Cole plots of synthesized materials noticeably revealed grain boundary contribution. The appearance of single semi-circle in impedance Cole-Cole graphs confirms the exceptional role of grain boundaries in the conduction process. The considerably lower dielectric parameters of investigated nano X-type ferrites propose their feasibility for high-frequency applications (phase shifters, dielectric resonators, stealth technology etc).     

Temperature/pH/magnetic triple‐sensitive nanogel–hydrogel nanocomposite for release of anticancer drug

Hydrogels, nanogels and nanocomposites show increasing potential for application in drug delivery systems due to their good chemical and physical properties. Therefore, we were encouraged to combine them to produce a new compound with unique properties for a long‐term drug release system. In this regard, the design and application of a nanocomposite hydrogel containing entrapped nanogel for drug delivery are demonstrated. To this aim, we first prepared an iron oxide nanocomposite nanogel based on poly(N‐isopropylacrylamide)‐co‐((2‐dimethylaminoethyl) methacrylate) (PNIPAM‐co‐PDMA) grafted onto sodium alginate (NaAlg) as a biocompatible polymer and iron oxide nanoparticles (ION) as nanometric base (PND/ION‐NG). This was then added into a solution of PDMA grafted onto NaAlg. Through dropwise addition of mixed aqueous solution of iron salts into the prepared polymeric solution, a novel hydrogel nanocomposite with excellent pH, thermal and magnetic responsivity was fabricated. The synthesized samples were fully characterized using Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy with energy‐dispersive X‐ray analysis, vibrating sample magnetometry and atomic force microscopy. A mechanism for the formation of PNIPAM‐co‐PDMA/NaAlg‐ION nanogel–PDMA/NaAlg‐ION hydrogel and PND/ION nanogel is suggested. Swelling capacity was measured at various temperatures (25 to 45 °C), pH values (from 2 to 11) and magnetic field and under load (0.3 psi) and the dependence of swelling properties of the nanogel–hydrogel nanocomposite on these factors was well demonstrated. The release rate of doxorubicin hydrochloride (DOX) as an anticancer drug was studied at different pH values and temperatures in the presence and absence of a magnetic field. The results showed that these factors have a high impact on drug release from this nanocomposite. The result showed that DOX release could be sustained for up to 12.5 days from these nanocomposite hydrogels, significantly longer than that achievable using the constituent hydrogel or nanogel alone (<1 day). The results indicated that the nanogel–hydrogel nanocomposite can serve as a novel nanocarrier for anticancer drug delivery. © 2019 Society of Chemical Industry     

Effect of Different Cosolvents on Transesterification of Waste Cooking Oil in a Microreactor

Biodiesel was prepared from waste cooking oil combined with methanol. The process was performed via transesterification in a microreactor using kettle limescale as a heterogeneous catalyst and various cosolvents under different conditions. n‐Hexane and tetrahydrofuran were selected as cosolvents to investigate fatty acid methyl esters (FAMEs). To optimize the reaction conditions, the main parameters affecting FAME% including reaction temperature, catalyst concentration, oil‐to‐methanol volumetric ratio, and cosolvent‐to‐methanol volumetric ratio were studied via response surface methodology. Under optimal reaction conditions and in the presence of the cosolvents n‐hexane and tetrahydrofuran, high FAME purities were achieved. Considering the experimental results, the limescale catalyst is a unique material, and the cosolvent method can reduce significantly the reaction time and biodiesel production cost.     

In vitro antimicrobial effects of Myristica fragrans essential oil on foodborne pathogens and its influence on beef quality during refrigerated storage

Nutmeg (Myristica fragrans) seed was subjected to the hydro-distillation method to extract its essential oil (NEO). Its main constituents were α-pinene (20.16%), sabinene (14.45%), and β-pinene (13.26%) with great antimicrobial and antioxidant actions. A novel edible coating was then fabricated based on the sage seed mucilage (SSM) and NEO, to ameliorate the quality and shelf-life of beef slices. The NEO-loaded SSM coating was able to significantly decrease the population of total viable count, Escherichia coli, Staphylococcus aureus, psychrotrophic bacteria, and fungi. Moreover, lipid oxidation of beef slices was remarkably suppressed upon the application of bioactive NEO-loaded SSM edible coating, as compared with the control by Day 6. The coated beef sample, especially NEO-rich SSM coated ones perceived a higher consumer acceptance and firmness than the SSM coated and noncoated samples. The SSM edible coating containing NEO could therefore have the potential to control the growth of pathogenic microorganisms and lipid oxidation, and to improve the color stability and sensory properties of meat and meat products.