全文获取类型
收费全文 | 167篇 |
免费 | 0篇 |
国内免费 | 9篇 |
专业分类
电工技术 | 1篇 |
综合类 | 2篇 |
化学工业 | 4篇 |
金属工艺 | 62篇 |
机械仪表 | 16篇 |
建筑科学 | 6篇 |
轻工业 | 9篇 |
无线电 | 1篇 |
一般工业技术 | 49篇 |
冶金工业 | 26篇 |
出版年
2022年 | 1篇 |
2021年 | 2篇 |
2020年 | 1篇 |
2019年 | 4篇 |
2018年 | 1篇 |
2017年 | 1篇 |
2016年 | 3篇 |
2015年 | 2篇 |
2014年 | 9篇 |
2013年 | 2篇 |
2012年 | 5篇 |
2011年 | 9篇 |
2010年 | 8篇 |
2009年 | 24篇 |
2008年 | 11篇 |
2007年 | 20篇 |
2006年 | 11篇 |
2005年 | 14篇 |
2004年 | 9篇 |
2003年 | 5篇 |
2002年 | 7篇 |
2000年 | 8篇 |
1999年 | 3篇 |
1994年 | 2篇 |
1993年 | 7篇 |
1992年 | 4篇 |
1988年 | 2篇 |
1987年 | 1篇 |
排序方式: 共有176条查询结果,搜索用时 15 毫秒
1.
冷成型模具低温锌系磷化 总被引:4,自引:1,他引:3
研制出适用于冷成型模具高硬度表面的低温锌系磷化工艺。其中磷化液含Zn(H2 PO4 ) 2 ·2H2 O 6 0g/L ,Zn(NO3) 2 ·6H2 O 90g/L ,NaNO2 1.5g/L ,稀土促进剂 0~ 1.0g/L ,游离酸度 4~ 6点 ,总酸度 70~ 75点。该磷化液在 4 0℃下 ,处理 30~ 4 0min后可获得厚约 10 μm的磷化膜。性能测试表明 ,其减摩、润滑性能良好 ,摩擦系数约降 0 .1,与未处理试样相比磨损量下降 96 % ,附着力 1级。 相似文献
2.
3.
Large-scale field shear tests on ten specimens of the red-sandstone embankment at a highway in Hunan, China, were performed to examine mechanical characteristics and parameters of red-sandstone. The curves of thrust-dispiacement, failure mode, and shear strength parameters for red-sandstone with different water contents, different compactions, and different grain size distributions were obtained from the tests. A practical procedure of in-situ test for red-sandstone embankment was proposed to normalize the test equipment and test steps. Based on three-dimensional thrust-sliding limit equilibrium method, the formulas for calculating strength parameters of red-sandstone considering three-dimensional sliding surface were inferred. The results show that red-sandstone has typical complete curves of stress-strain, strain softening, which are caused by the special structure of red-sandstone; water content and compaction are important factors for strength and failure mode of red-sandstone; The average value of cohesion and internal friction angle of the specimens calculated by three-dimensional technique are 21.56 kPa and 29.29°, respectively, and those by traditional two-dimensional method are 25.52 kPa and 33.76°, respectively. 相似文献
4.
5.
等离子显示器(PDP)用BaMgAl10O17:Eu2+蓝粉的烧结工艺研究 总被引:5,自引:0,他引:5
研究了烧结温度、保温时问以及粘结剂对荧光粉二次性能的影响。结果表明,当采用较低烧结温度时,有机粘结剂没有完全分锵是造成荧光粉亮度下降的主导因素,包覆在荧光粉表面的残留部分降低了荧光粉的表面光透率;当烧结温度升高,粘结剂的影响逐渐下降,而过高的烧结温度在导致荧光粉劣化各种因素之间起到了决定性的作用。在此基础上,依据对粘结剂中成膜物质乙基纤维素的降解特性的分析,对浆料烧结工艺进行了优化。结果表明,当浆料加热至480℃,有机粘结剂分解已趋于饱和,从而可以有效降低烧结工序对荧光粉的不利影响。 相似文献
6.
7.
8.
9.
在碳酸铝铵法制备氧化铝工艺的基础上,通过加入晶体生长促进剂及改变热分解工艺等方法,有效控制了α-Al2O3颗粒的大小和形貌。结果表明:促进剂对α-Al2O3的相变过程影响很大,加入促进剂后使其相转变温度降低了200℃,至1000℃时已完全转变为α-Al2O3相;升温方式对α-A2lO3颗粒的形貌影响很大,将含促进剂的样品直接入高温炉煅烧时,倾向于形成六角片状颗粒;而先低温后高温煅烧时则会形成圆饼状颗粒。通过控制升温过程,可以控制得到粒径较小的圆饼状α-Al2O3颗粒,且分散性良好。 相似文献
10.
研究了Ba含量及掺杂Mg、Sr对BaAl12O19单相合成的影响.研究结果表明Ba1+xAl12O19+x中Ba含量在1.1~1.2时,α-Al2O3和BaAl2O4相残余难以被XRD检出;Mg的掺入可以优化BaAl12O19的结晶,Ba11MgyAl12-yO191-y/2中Mg的含量在0.8~1.1时可以获得单相;掺Sr使部分衍射峰位置向高角度方向漂移,Ba1
2-zSrzMg0 8Al1.2O18.8中Sr的掺入量为0.4左右时合成出更为纯净的单相. 相似文献