掺钪AlN材料特性及HBAR器件性能研究

该文基于掺钪AlN薄膜制备了高次谐波体声波谐振器(HBAR),研究了钪(Sc)掺杂浓度对AlN压电薄膜材料特性及器件性能的影响。研究表明,当掺入Sc的摩尔分数从0增加到25%时,压电应力系数e₃₃增加、刚度 下降,导致Al₁-_xSc_xN压电薄膜的机电耦合系数 从5.6%提升至15.8%,从而使HBAR器件的有效机电耦合系数 提升了3倍。同时,当Sc掺杂摩尔分数达25%时,Al₁-_xSc_xN(x为Sc掺杂摩尔分数)压电薄膜的声速下降13%,声学损耗提高,导致HBAR器件的谐振频率和品质因数降低。     

The analysis and comparison of two novel kinds of focusing elements as reflectors

In this article, two novel kinds of focusing elements as reflectors are analyzed and compared. One is the grooved Fresnel zone plate reflector with continuous phase‐correcting. The other called subzone paraboloid reflector, has the profile that consists of a series of paraboloids. Their diffraction efficiencies and bandwidths are described. The two elements still preserve the advantages of Fresnel zone plates, namely, low profile, high efficiency, and simple fabrication. Two dual‐reflector antennas using the proposed focusing elements as the main reflectors are simulated and the results show that these antennas have good radiation performances. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:101–108, 2015.     

Rational Designs for Lithium-Sulfur Batteries with Low Electrolyte/Sulfur Ratio

Lithium-sulfur batteries (LSBs) are considered a promising next-generation energy storage device owing to their high theoretical energy density. However, their overall performance is limited by several critical issues such as lithium polysulfide (PS) shuttles, low sulfur utilization, and unstable Li metal anodes. Despite recent huge progress, the electrolyte/sulfur ratio (E/S) used is usually very high (≥20 µL mg⁻¹), which greatly reduces the practical energy density of devices. To push forward LSBs from the lab to the industry, considerable attention is devoted to reducing E/S while ensuring the electrochemical performance. To date, however, few reviews have comprehensively elucidated the possible strategies to achieve that purpose. In this review, recent advances in low E/S cathodes and anodes based on the issues resulting from low E/S and the corresponding solutions are summarized. These will be beneficial for a systematic understanding of the rational design ideas and research trends of low E/S LSBs. In particular, three strategies are proposed for cathodes: preventing PS formation/aggregation to avoid inadequate dissolution, designing multifunctional macroporous networks to address incomplete infiltration, and utilizing an imprison strategy to relieve the adsorption dependence on specific surface area. Finally, the challenges and future prospects for low E/S LSBs are discussed.     

High-rate capability of carbon-coated micron-sized hexagonal TT-Nb2O5 composites for lithium-ion battery

With excellent specific capacity, superior cycle stability, safety and strong practical, Nb₂O₅ has been considered as one of the prospective anode materials for lithium-ion batteries (LIBs). However, current study suggests that Nb₂O₅ electrode materials for LIBs still face the vital issues of low electrical conductivity and poor rate performance. Therefore, carbon-coated TT-Nb₂O₅ materials are designed and synthesized through solid state method in this work, which present high specific capacity (228 mA h g^?1 at 0.2C), satisfactory rate properties (107 mA h g^?1 at 20 C). The outstanding electrochemical property can not only give the credit to the pseudocapacitance effect of TT-Nb₂O₅, but also attribute to introduction of carbon. The homogeneous carbon-coated materials enhance the electrical conductivity, increase the electron transmission speed and alleviate particle crushing. This research not only offers a new method for preparing excellent electrode materials, but also provides a kind of excellent anode material with prospective application for LIBs.     

Corrosion behavior of Cu–Sn bronze alloys in simulated archeological soil media

The corrosion behavior of synthetic Cu–Sn bronze alloys with six different Sn contents was examined through an electrochemical test and a synthetic test in a simulated corrosive medium. The mechanism of corrosion and the morphology of the corroded surfaces were characterized through field emission scanning electron microscopy equipped with energy-dispersive spectroscopy. At the corrosion potential, the corrosion behavior appears to be determined by the charge transfer step and the diffusion process. It was found that the bronze-IV (Cu–26.8Sn) specimen exhibited the best corrosion resistance, as evidenced by a low corrosion current density and a high impedance. This improvement resulted from an increase in the content of the Cu–Sn solid solution in the alloy, which was conducive to forming a relatively more protective passive film on the surface of the bronze alloy. This finding would be valuable in the anticorrosion protection of archeological artefacts after their excavation.     

Analysis of the Scattering Characteristic of Several Waveguide Components Using Boundary Element Method

Several kinds of waveguide components such as curved waveguide bends, arbitrary angle waveguide bends and T-junctions have been analyzed with boundary element method in this paper. A new discretization method for the boundary element method to solve the waveguide discontinuities has been given. The numerical results obtained agree well with the experimental results and numerical results in other literature. Especially, the scattering characteristics of Forded E-, H-plane T-junctions in 3mm band have been analyzed using boundary element method and the calculation results are presented.     

Long multifilament Bi-2223 Ag-sheathed superconducting tapes and solenoids

Multifilament Ag-sheathed BiPbSrCaCuO (2223) superconducting tapes containing 49 filaments were fabricated by the powder-in-tube route and the roll-anneal process. The transport critical current densityJ _c was 1.3×10⁴ A cm^–2 at 77 K and 7×10⁴ A cm^–2 at 4.2 K in self-field. A 12-m-long tape was used to construct superconducting solenoids (50, 28, and 14 mm internal diameters) generating dc fields 380–1070 G at 4.2 K. Measurements of the variation ofJ _c with field (0–1.6 T) and bend strain (0–5%) are used to explain the performance of the solenoids. The critical bend strain of tapes was about 1.5%.     

云南丽江旅游的发展与大研古镇的发展方向问题

一、发展过程与现状 (一)古城和雪山完美地结合,特点突出,古镇拉动效应明显 丽江有丰富的旅游资源,如独特的东巴文化、古城、雪山等等。经过一段时间发展,丽江旅游产品也形成几个比较突出的亮点,如古城-雪山产品,古城如此完整,雪山的风貌如此突出,而且古城和雪山在不大的地理范围内集中到一起,这在国内是很难得的。古城被评为世界文化遗产后还形成了一个显著的市场拉动效应。     

cdma1x无线子系统导频信道功率分配分析

分析了目前联通CDMA网络建设中的主要问题之一——导频功率分配问题。主要介绍了cdma 1x系统的信道类型，以及前向链路信道功率分配原则，并且对导频信道功率与无线网络覆盖和容量之间的关系进行了初步探讨。