Control Model for Large‐Sized Gantry Type Linear Motor Slider

At present, many industrial carrier devices utilize linear motor sliders. However, a heavier load requires a linear motor (which is an example of a direct drive device) to get higher power, compared with a rotary motor with a ball screw slider (which is an example of an indirect drive device). In order to obtain higher power at a lower cost, a linear slider with multiple motors can be utilized, for example, a gantry type linear motor slider. Moving the gantry type slider requires two linear motors that are set up in parallel to enable synchronization control. Some conventional synchronization control methods have been proposed for the parallel twin linear slider; however, a large‐scaled gantry type linear motor slider has two unique problems: mechanical distortion caused by the limitations of installation environment and coupling caused by joints with low stiffness. This paper proposes a control model to solve these problems, and an identification method of each parameter. Furthermore, the effectiveness of the control model is verified by comparison with simulation results and experimental results.     

Development of –1 MV DC Filter and High‐Voltage DC Measurement Systems for ITER NBI

This paper presents the development results of a ?1 MV dc filter and dc measurement systems for an ITER (International Thermonuclear Experimental Reactor) neutral beam injector (NBI) system. High accuracy of 0.5% and fast responsivity of 3.3 μs, ?3 dB are required for the dc measurement systems: both dc voltage dividers and DCCTs. Circuit design and thermal flow design were carried out to clarify and minimize their effects on the accuracy and responsivity. The validity of the established design was demonstrated by the actual‐product tests; temperature rise of each components fell below the allowable value; inner components of dc filter withstood dc ?1.2 MV; each voltage divider accurately measured the voltage during the dc ?1.2 MV withstand voltage test; the voltage dividers and the DCCTs were adequate to the requirements of responsivity (3.3 μs, ?3 dB).     

Ethylene Absorbent to Maintain Quality of Lightly Processed Fruits and Vegetables

Ethylene had an undesirable effect on the quality of kiwifruits, bananas, broccoli, and spinach leaves that were prepared and stored as lightly processed products. A 2.or 20 ppm ethylene treatment hastened the softening of the pulp of kiwifruits and bananas held at 20°C. Use of charcoal with palladium chloride, as ethylene absorbent, prevented the accumulation of the ethylene and was effective in reducing the rate of softening in kiwifruits and bananas and of chlorophyll loss in spinach leaves, but not in broccoli.     

1-乙氧基-2-丙醇/水/癸烷的液液平衡

引　言石油是目前最重要的能源 ,除了液体石油外 ,油砂和油岩也能作为石油资源 .油岩分散存在于砂岩层中 ,只能通过物理的方法开采 ,乳化是可利用的提取方式之一 .为了了解乳化的原理及其体系的变化动态 ,作者曾经考察了 2 乙氧基乙醇、癸烷和水的液液三相平衡[1] .作为系统研     

High‐Voltage Power Generation on Spacecraft

Spacecraft need high‐voltage power generation for high power. However, the high voltage can cause severe discharge problem on spacecraft. This paper describes the mechanism of spacecraft charging and discharging. Mitigation methods are also mentioned.     

Development of Electrolytic Capacitor Less Photovoltaic Grid Connected Inverter with Boost‐Up Type Active Buffer Circuit

This paper proposes a configuration of a single‐phase voltage source inverter that features power decoupling capability. Generally, the converter connected to a single‐phase grid employs bulky dc link capacitors such as electrolytic capacitors in order to decouple the power ripple with twice the frequency of the power supply. The power ripple in the proposed circuit is compensated by an active buffer with small capacitors. In this paper, the fundamental operations of the proposed converter are confirmed by experimental results. From the experimental results, the output current total harmonic distortion (THD) is 3.51%, the ratio of the input current is 14.3%, and the output power factor is over 99%. In addition, the volume of the proposed circuit is reduced by 61% when the carrier frequency is 64 kHz compared to that with a carrier frequency of 16 kHz. Finally, from an evaluation of the power density using Pareto front curves, the proposed circuit achieves high power density in comparison with the conventional circuit.     

Work of Fracture and Crack Healing in Glass

The work of fracture, γwoF, of a soda-lime-silica glass was determined as 5.5 J/m² in an inert atmosphere and 4.4 J/m² in air by using a short bar specimen with a chevron notch. The critical stress intensity factor K_IC calculated from γ_wof obtained in an inert atmosphere agreed with the value, 0.88 MN/m^3/2, determined by the indentation method. In unloading-loading cycles during stable crack growth, crack healing was observed both on the diagram of load vs load-point displacement and visually. Crack healing is more prevalent in an inert atmosphere, occurring only minimally in air. The energy for healing was measured as 0.65 J/m² in an inert atmosphere and ∼0.21 J/m² in air.     

RAPID MESOCARP CELL ELONGATION ENHANCES GUMMING SYNDROME IN JAPANESE APRICOT (PRUNUS MUME SIEB. ET ZUCC.) FRUIT

ABSTRACT

Japanese apricot (Prunus mume Sieb. et Zucc.) ‘Benisashi’ fruit tends to show the physiological disorder of a gumming syndrome, while the fruit known as ‘Nanko’ rarely show this. The accumulated gum becomes a solid gel during the processing period and the commercial value of the mume pickle is consequently decreased. In the present experiment, gum accumulation in the mesocarp tissue and the cell size of the tissue during fruit growth were observed in the two cultivars. In mid‐May, the initiation of the gum duct was observed in vascular bundles in the mesocarp tissue of the two cultivars and plant gum was then observed to accumulate in the duct. No difference in these phenomena was observed between the cultivars until late May. Thereafter, ‘Benisashi’ developed a gum lump visible to the naked eye during Stage III, while the gum lump of ‘Nanko’ did not develop to the visible size as shown in ‘Benisashi’; the lumps could not be confirmed with the naked eye until the mature stage. ‘Benisashi’ showed more rapid fruit growth compared with ‘Nanko’ during Stage III due to explosive mesocarp cell elongation close to the endocarp. Moreover, the rate of gumming fruit of ‘Benisashi’ was higher in bigger fruits than smaller ones. These results indicate that the peculiar cell growth of ‘Benisashi’ fruit may accelerate gum lump formation.

PRACTICAL APPLICATIONS

Gumming syndrome affects the quality of mume pickle. In this experiment, we investigated the mechanisms of gum accumulation in fruit flesh. ‘Benisashi’, which frequently shows the gumming syndrome, presented rapid inner mesocarp cell growth on fruits developing Stage III. This peculiar cell growth may accelerate gum lump formation. Therefore, we have to prevent the cultivational misconduct that induces rapid fruit growth in this period to suppress the gumming syndrome and to increase the commercial value of mume pickle. Moreover, this knowledge is also important in order to breed the new cultivars which do not contain the gumming syndrome.

     

Rinsing Behavior of Deposited Layers Formed on Membranes in Ultrafiltration

Skim milk and aqueous milk protein suspensions were ultrafiltered in a tubular module under controlled conditions (temperature, pressure, flow rate) and were subsequently rinsed with water also under controlled conditions. The effect of rinsing on the deposited layer was followed by observing the flux with time. Ultrafiltration and rinsing should be carried out at high flow rates and at low pressures. Increasing the pressure led to an undesirable increase in the compactness of the deposit. Theoretical considerations of the mechanism of transport in and at the deposited layer made it possible to obtain data on the thickness of the deposits, on mass transfer coefficients and velocity profiles within deposits. The experimental rinsing curves could be well explained by the calculated results. The results should help to optimize the performance and cleaning of UF modules.     

Microstructural development with crystallization of hexagonal boron nitride

Abstracts are not published in this journal This revised version was published online in November 2006 with corrections to the Cover Date.