Surface treatment of titanium dioxide nanopowder using rotary electrode dielectric barrier discharge reactor

Titanium dioxide (TiO2) nanopowder (P-25;Degussa AG) was treated using dielectric barrier discharge (DBD) in a rotary electrode DBD (RE-DBD) reactor.Its electrical and optical characteristics were investigated during RE-DBD generation.The treated TiO2 nanopowder properties and structures were analyzed using x-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR).After RE-DBD treatment,XRD measurements indicated that the anatase peak theta positions shifted from 25.3° to 25.1°,which can be attributed to the substitution of new functional groups in the TiO2 lattice.The FTIR results show that hydroxyl groups (OH) at 3400 cm-1 increased considerably.The mechanism used to modify the TiO2 nanopowder surface by air DBD treatment was confirmed from optical emission spectrum measurements.Reactive species,such as OH radical,ozone and atomic oxygen can play key roles in hydroxyl formation on the TiO2 nanopowder surface.     

Synergistic Effects of Polybenzimidazole and Aramide on Enhancing Flame-Retardancy and Solubility

Aromatic and functional polymers with processibility derived from biobased starting materials are prerequisite considering sustainable society. Poly(2,5-benzimidazole)s are rigid-rod polymers to show ultrahigh thermal stability such as flame retardance, while usually suffer from poor solubility. Here, poly(benzimidazole-co-amide)s are synthesized from two biobased monomers, 3,4-diaminobenzoic acid and a semirigid comonomer, 4-aminohydrocinnamic acid. The copolymers with an amide composition of 80 mol% and higher are soluble in widely used polar solvents to fabricate the films keeping high flame retardance, which is comparable with popular high-performance polymers such as aromatic polyimides, polyetheretherketone, polyphenylene sulfide, etc.     

Evaluation of inelastic constitutive models under plasticity-creep interaction for steel at 600°C

Uniaxial tests to identify plasticity-creep interaction in steel at 600°C were carried out as the Benchmark Project by the Subcommittee on Inelastic Analysis and Life Prediction, JSMS. The purpose of this paper is to present recent experimental data and predictions of constitutive models obtained in the project. Ten types of constitutive models were utilized to compare analytical predictions to sixteen benchmark experiments which are grouped into four categories: (I) tensile and creep tests under monotonic loading, (II) mixed mode tests under plastic and creep loading, (III) ratcheting deformation tests under program loads, and (IV) cyclic deformation tests under the combination of different strain rates. The benchmark tests in Group IV are used to estimate the creep-fatigue life of steel; the results will be published in a separate paper.     

Preparation of Laminin-apatite-polymer Composites Using Metastable Calcium Phosphate Solutions

A synthetic polymer with a laminin-apatite composite layer on its surface would be useful as a percutaneous device. The preparation of such a composite was attempted in the present study using poly（ ethylene terephthalate ） （PET） and polyethylene （PE） as the synthetic polymer. PET and PE plates and those pretreated with an oxygen plasma were alternately dipped in calcium and phosphate ion solutions, and then immersed in a metastable calcium phosphate solution supplemented with laminin （ LCP solution ）. The PET and PE plates pretreated with an oxygen plasma formed a uniform and continuous layer of a laminin-apatite composite on their surfaces. In contrast, the PET and PE plates that had not been pretreated with an oxygen plasma did not form a continuous layer of a laminin-apatite composite on their surfaces. The hydrophilic functional groups on the PET and PE surfaces introduced by the plasma treatment were responsible for the successful laminin-apatite coruposite coating.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

A 0.1-μm delta-doped MOSFET fabricated with post-low-energyimplanting selective epitaxy

A simple fabrication technology for delta-doped MOSFETs, named post-low-energy implanting selective epitaxy (PLISE) is presented. The PLISE technology needs no additional photo-lithography mask, deposition step or etching step even for CMOS devices. The only additional step is growing undoped epitaxial channel layers by UHV-CVD after the channel implantation. With this technology, delta-doped NMOSFETs with 0.1-μm gate length were successfully fabricated. By optimizing the epi-layer thickness and the channel doping level, short-channel effects are suppressed enough to achieve 0.1-μm gate length. Moreover, the junction capacitance at zero bias is reduced by 50%     

The temperature dependence of luminescence from a long-lasting phosphor exposed to ionizing radiation

The temperature dependence of luminescence from a long-lasting phosphor (LLP), SrAl₂O₄ : Eu²⁺,Dy³⁺, exposed to ionizing radiation has been measured to understand the LLP luminescence mechanism. Evaluation of the decay constants of the LLP exposed to -, β- or γ-rays at temperatures from 200 to 390 K showed that the decay constant is divided into four components ranging from 10⁻⁴ to 10⁻¹ s⁻¹ with activation energies of 0.02–0.35 eV.

Total luminous intensity from the LLP with changing irradiation temperature has its maximum value around the room temperature. Irradiation at elevated temperature (390 K) has the total luminescence pattern with monotonous decrease as temperature rises. As a result of evaluating the temperature dependence of luminescence, the luminescence mechanism is considered as follows:

Full-size image

 

Fiber-optic devices for local area network application

Recent developments on fiber-optic devices are reviewed from the local area network (LAN) application viewpoint. Future technical trends are also discussed, along with current research activities. In local area network systems, low device cost and easy maintenance or maintenance-free devices are especially required. Light sources and photodetectors suitable for the systems are described. InGaAsP/InP light emitting diodes can cover a broad application field, up to a gigabits per second super high-speed network region. Optical passive devices, which include branching couplers, switches and connectors, are mentioned as essential components. Compact transmitter/receiver module technology is a key factor in realizing optical-fiber local area network systems. An example of 200-Mbit/s transmitter/receiver module is reported.