Synthesis of Janus polyaniline–polyelectrolyte complex membrane via in situ confined polymerization

Polyelectrolyte complex (PEC) membranes prepared from poly(styrene sulfonate) (PSS) and poly(diallyldimethylammonium chloride) (PDADMAC) were modified by crossflow polymerization of aniline (ANI). The PEC membranes were used as separators in a two-compartment setup where ANI monomer and ammonium persulfate (APS) oxidant diffused through the membranes to form polyaniline (PANI). APS and ANI having different distributions throughout the membranes, the reaction led to the asymmetric polymerization of PANI on one face of each PEC membrane thus producing Janus membranes. Due to the excess PANI content, the membrane displayed distinct asymmetric electrical conductivities on each face. Interestingly, very different ANI polymerizations were obtained when nonstoichiometric PEC membranes having different molar ratio of cationic and anionic polyelectrolytes (P⁺:P^? represents PDADMAC:PSS) were used and transport of APS was fastest through the 2:1 PEC when compared to the 1:2 PEC. In all experiments, the polymerization was most intense on the ANI side of the membranes. Also, the influence of NaCl both during PEC fabrication and during polymerization was studied and found to have some effect on the solute permeability. Results showed that a higher content of PANI was formed on PEC membranes having excess P⁺ and with no NaCl added during PEC fabrication. Although X-ray diffraction confirmed the presence of PANI on both sides of each membrane, scanning electron microscopy images demonstrated that both sides of each membrane had different PANI content deposited. Electrical conductivity measurements using a four-point probe setup also showed that the PEC–PANI exhibits asymmetric electrical property on different sides. © 2021 Society of Industrial Chemistry.     

Droplet Entrainment Analysis in a Flash Evaporator with an Image-Based Measurement Technique

Local droplet sizes and volumes of entrained liquid are captured with an image-based measurement technique for comparison with a conventional, integral method for entrainment analysis. Experiments in a forced circulation flash evaporation were performed for different operating conditions and with two different chemical systems. Droplet size and frequency rise with an increase in thermal energy input. The local readings confirm the trends found by the integral measurement method. The modification of the image-based probe enables the detection of small (≈ 10 µm) and at the same time fast droplets under challenging operating conditions, such as vacuum and superheated feed similar to industrial process conditions.     

Exergy analysis of the diesel pre-reforming solid oxide fuel cell system with anode off-gas recycling in the SchIBZ project. Part I: Modeling and validation

Solid oxide fuel cell (SOFC) systems with anode off-gas recirculation (AGR) and diesel pre-reforming are advantageous because they can operate with the current fuel infrastructure. In the SchIBZ-project, the prototype of such a SOFC system for maritime applications has already been commissioned. In this first paper, we model the system devices to conduct an exergy analysis of this real SOFC plant and validate them with experimental values from experiments in laboratory scale. The results of our simulation agree well with the experimental values. The calculations with the validated results may be closer to the real thermodynamic behavior of such system components than previous literature.     

Evaluation of dynamic modulus measurement for C/C-SiC composites at different temperatures

The determination of elastic properties at application temperature is fundamental for the design of fibre reinforced ceramic composite components. An attractive method to characterize the flexural modulus at room and high temperature under specific atmosphere is the nondestructive Resonant Frequency Damping Analysis (RFDA). The objective of this paper was to evaluate and validate the modulus measurement via RFDA for orthotropic C/C-SiC composites at the application temperature. At room temperature flexural moduli of C/C-SiC with 0/90° reinforcement were measured under quasi-static 4-point bending loads and compared with dynamic moduli measured via RFDA longitudinally to fibre direction. The dynamic modulus of C/C-SiC was then measured via RFDA up to 1250°C under flowing inert gas and showed an increase with temperature which fitted with literature values. The measured fundamental frequencies were finally compared to those resulting from numerical modal analyses. Dynamic and quasi-static flexural moduli are comparable and the numerical analyses proved that bending modes are correctly modeled by means of dynamic modulus measured via RFDA. The nondestructive RFDA as well as the numerical modeling approach are suitable for evaluation of C/C-SiC and may be transferred to other fibre reinforced ceramic composite materials.     

Three stage creep behavior of MgO containing ordinary refractories in tension and compression

In service tensile and compressive stresses occur in refractory linings, these stresses lead to creep of refractories. Ordinary refractories experience creep of the primary stage and may further proceed to the secondary and tertiary creep stage. For the development of advanced material models for finite element simulations it is necessary to investigate the creep behavior in all three creep stages under tensile and compressive loads. Hence, two advanced high temperature uniaxial creep testing devices, applying a wide range of tensile and compressive loads, were used to determine the three creep stages in a reasonable time under service related loading conditions. The Norton–Bailey creep equations and an inverse identification procedure were applied for the evaluation of the experimental results. A magnesia refractory was studied at elevated temperatures and its respective creep parameters for each stage were determined. The stress dependency on the creep behavior can be seen clearly on the creep curves and the corresponding creep parameters. Furthermore, a comparative study of creep parameters and creep rates was performed between the magnesia refractory and a magnesia-chromite refractory. The results demonstrate the significant asymmetrical creep behavior in tension and compression for both materials. The creep investigation in this paper favors the requirement for consideration of the three stage creep behavior and the asymmetrical creep behavior in thermomechanical modelling activities of industrial vessels.     

Heat propagation in thermally conductive polymers of PA6 and hexagonal boron nitride

Thermally conductive polymers offer new possibilities for the heat dissipation in electric and electronic components, for example, by a three‐dimensional shaping of the heat sinks. To face safety regulations, improved fire performance of those components is required. In contrast to unfilled polymers, those materials exhibit an entirely different thermal behavior. To investigate the flammability, a phosphorus flame retardant was incorporated into thermally conductive composites of polyamide 6 and hexagonal boron nitride. The flame retardant decreased the thermal conductivity only slightly. However, the burning behavior changed significantly, due to a different heat propagation, which was investigated using a thermographic camera. An optimum content of hexagonal boron nitride for a sufficient thermal conductivity and fire performance was found between 20 and 30 vol%. The improvement of the fire performance was due to a faster heat release out of the pyrolysis zone and an earlier decomposition of the flame retardant. For higher contents of hexagonal boron nitride, the heat was spread faster within the part, promoting an earlier ignition and increasing the decomposition rate of the flame retardant.     

Creep testing of carbon containing refractories under reducing conditions

Mechanical testing of carbon containing refractories at high temperatures requires measures to protect the sample from oxidation. Therefore, special setups for tensile and compressive creep testing were developed to prevent the oxidation of carbon in the sample. A MgO-C refractory was selected for a case study. These developments allow the quantification of the tensile and compressive creep behaviour of MgO-C refractories at temperatures up to 1500?°C. The creep parameters are determined by an inverse evaluation method for the obtained experimental data. They enable the consideration of creep in a thermomechanical finite element simulation of refractory linings in service.     

Elastic instabilities,microstructure transformations,and pattern formations in soft materials

Large deformations of soft materials can give rise to the development of various elastic instabilities. The phenomenon is associated with a sudden and dramatic change in structure morphologies. The underlying mechanism is crucial for the formation of complex morphologies in biology. Moreover, the concept of instability-induced pattern transformations is promising for designing novel materials with switchable functions and properties. In this paper, we review the state of the art in elastic instability phenomena in soft materials. We start by considering the classical buckling in beam-based structure lattice designs. Then, we discuss the instability-induced microstructure transformations in soft porous materials, and heterogeneous multiphase and fiber composites. Next, the mechanisms – often involving the post-buckling consideration – leading to the wrinkling and folding, creasing, fringe, and fingering are discussed.     

Diamine oxidase supplementation improves symptoms in patients with histamine intolerance

Food Science and Biotechnology - Histamine intolerance (HIT) is thought to be caused by a disproportionate amount of histamine in the body. The enzyme diamine oxidase (DAO) is considered for the...