Synthesis of thermoresponsive copolymer/silica-coated magnetite nanoparticle composite and its application for heavy metal ion recovery

To enhance chemical stability and suppress of aggregation of magnetite nanoparticles (MNPs), which are used as a support for thermoresponsive copolymer immobilization, silica coating of the MNPs is applied via the electrooxidation method. Although the resulting silica coated-MNPs also formed aggregates, the size distribution of the aggregate shifted to smaller size range. Because of that, the surface area available for copolymer immobilization increased approximately 6.7 times at maximum as compared with that of the uncoated MNPs. It contributed to the increase of the amount of the immobilized copolymer on the silica-coated MNPs, which is approximately four times larger than that on the uncoated MNPs. Fe₃O₄ dissolution test confirmed enhancement of chemical stability of MNPs. The thermoresponsive copolymer immobilized on the silica-coated MNPs shows the ability to recycle Cu(II) ion from Cu(II) containing solution by changing temperature with significantly shorter time than those in other thermoresponsive adsorbents in gel form.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Recent activities in the field of Nuclear Operational Management and Nuclear Safety Engineering

Recent activities in the field of Nuclear Operational Management and Nuclear Safety Engineering, the studies related to risk analysis methodology, design, and operational management, physical phenomena, and emergency preparedness and nuclear security, have been progressed. Especially, ‘risk analysis methodology’ and ‘design and operational management’ are the main categories of the field, in which more than half of published articles on Journal of Nuclear Science and Technology are related to these categories.     

Aqueous One-pot Synthesis of Glycopolymers by Glycosidase-catalyzed Glycomonomer Synthesis Using 4,6-Dimetoxy Triazinyl Glycoside Followed by Radical Polymerization

Glycopolymers have attracted increased attention as functional polymeric materials, and simple methods for synthesizing glycopolymers remain needed. This paper reports the aqueous one-pot and chemoenzymatic synthesis of four types of glycopolymers via two reactions: the β-galactosidase-catalyzed glycomonomer synthesis using 4,6-dimetoxy triazinyl β-D-galactopyranoside and hydroxy group-containing (meth)acrylamide and (meth)acrylate derivatives as the activated glycosyl donor substrate and as the glycomonomer precursors, respectively, followed by radical copolymerization of the resulting glycomonomer and excess glycomonomer precursor without isolating the glycomonomers. The resulting glycopolymers bearing galactose moieties exhibited specific and strong interactions with the lectin peanut agglutinin as glycoclusters.     

Study of the Antioxidative Properties of Several Amino Acid-Type Surfactants and their Synergistic Effect in Mixed Micelle

Cysteine and methionine, two sulfur-containing amino acids (AA), were introduced in their surfactant forms as potential antioxidants. The antioxidative (AOX) properties of lauroyl methionine (C12-Met) and lauroyl cysteine (C12-Cys) was investigated by means of the oxygen radical absorbance capacity assay. Both the surfactants exhibited excellent AOX behavior at the premicellar state and micellar medium. The AOX behavior was found to be comparable for both the surfactants at their premicellar states. However, in micellar medium, C12-Met showed better AOX property than C12-Cys. The AOX power of the surfactants was compared with other previously developed AA-type surfactants. The order of the AOX power was found to be: C12-tryptophan > C12-tyrosine ≈ C12-methionine ≈ C12-cysteine > C12-histidine at the premicellar state and C12-tryptophan > C12-tyrosine > C12-methionine > C12-cysteine > C12-histidine at the micellar state. C12-Cys displayed lower AOX property in micellar medium due to its dimer formation tendency. Based on the HPLC and UPLC-Q-TOF-MS analysis, the dimer formation of C12-Cys was found to be accelerated due to the micellar environment and results into negative synergistic effect on other aromatic AA-type surfactants. However, the presence of C12-His in the micellar solution of C12-Cys resulted no synergistic effect due to stronger H-bonding between the surfactants and resulting less dimer formation.     

Graded evolution of anisotropic microstructure during sintering from crystal-oriented powder compact

Anisotropic sintering, including shrinkage and grain growth, was examined for c-axis-oriented (Sr,Ca)₂NaNb₅O₁₅ (SCNN) ceramics, which were prepared by colloidal processing under a magnetic field. In the c-axis-oriented SCNN powder compact, shrinkage and grain growth along the c-axis were higher than those along the a-axis. The anisotropic microstructural development was clearly associated with anisotropic sintering shrinkage. X-ray diffraction, scanning electron microscopy, and energy back scattering diffraction showed that the grain growth of oriented particles by including random grains contribute to the development of the oriented microstructure. Finally, the highly crystal-oriented SCNN ceramics with a densified microstructure were obtained through anisotropic sintering. These results clearly showed the potential to develop a well-defined anisotropic microstructure during sintering by designing and controlling the particle packing structure in a powder compact.     

The Potential Role of Hepatocyte Growth Factor in Degenerative Disorders of the Synovial Joint and Spine

This paper aims to provide a comprehensive review of the changing role of hepatocyte growth factor (HGF) signaling in the healthy and diseased synovial joint and spine. HGF is a multifunctional growth factor that, like its specific receptor c-Met, is widely expressed in several bone and joint tissues. HGF has profound effects on cell survival and proliferation, matrix metabolism, inflammatory response, and neurotrophic action. HGF plays an important role in normal bone and cartilage turnover. Changes in HGF/c-Met have also been linked to pathophysiological changes in degenerative joint diseases, such as osteoarthritis (OA) and intervertebral disc degeneration (IDD). A therapeutic role of HGF has been proposed in the regeneration of osteoarticular tissues. HGF also influences bone remodeling and peripheral nerve activity. Studies aimed at elucidating the changing role of HGF/c-Met signaling in OA and IDD at different pathophysiological stages, and their specific molecular mechanisms are needed. Such studies will contribute to safe and effective HGF/c-Met signaling-based treatments for OA and IDD.     

Propagation and termination of an internal crack in continuously cast austenitic stainless steel analyzed by ∑ values and the Schmid factor

The formation mechanism of an internal crack was clarified from the viewpoint of the crystallography and thermal expansion. An inverse pole figure map obtained by EBSD pattern showed that the crack propagated along the grain boundaries having high ∑ values within the columnar zone. After the crack initiation, these positions were considered to undergo cracking followed by propagation toward the equiaxed side. Near the termination position, the grains ahead of crack propagation had a Schmid factor higher than 0.45 consuming elastic strain energy. Thermal expansion measurements showed that the grain with (0 0 1) orientation had the largest expansion while that with (0 1 1) the smallest. The grain boundaries neighboring the combination of (0 0 1) and (0 1 1) grains had the largest thermal stress. Therefore, thermal stress contributed to the initiation of cracking. It was thus proposed to enlarge the equiaxed zone to prevent cracking by discontinuing the crack propagation.     

A short guide to topological terms in the effective theories of condensed matter

This article is meant as a gentle introduction to the topological terms that often play a decisive role in effective theories describing topological quantum effects in condensed matter systems. We first take up several prominent examples, mainly from the area of quantum magnetism and superfluids/superconductors. We then briefly discuss how these ideas are now finding incarnations in the studies of symmetry-protected topological phases, which are in a sense a generalization of the concept of topological insulators to a wider range of materials, including magnets and cold atoms.     

Iron Loss Calculation of AC Filter Inductor for Three‐Phase PWM Inverters

In recent years, remarkable advancement of new power semiconductor devices, such as SiC and GaN, enables the increase of switching frequency of power converters, and hence the volume of passive components, such as ac filters and transformers, can be reduced. However, temperature rise caused by the inductor loss is increasing, and hence iron loss evaluation of the inductor is one of the most important issues to realize high power density converters. Conventionally, an improved generalized Steinmetz equation (iGSE) has proposed in order to calculate the iron loss under a pulse voltage magnetizing condition. However, accurate iron loss calculation of the ac filter inductor used in a PWM inverter cannot be realized. The authors have proposed two methods of iron loss evaluation of ac filter inductors. The first one is a loss map method which can calculate the iron loss without using a real PWM inverter. Another one is an ILA (Inductor Loss Analyzer) which can measure the iron loss in every switching period in a real PWM inverter. In this paper, comparisons of the iron loss between the ILA and the loss map method on both the single‐phase and three‐phase inverters are studied. It is found that iron loss of the ac filter inductor in the three‐phase PWM inverter which is calculated by the loss map method cause a large error on a specific condition. In order to prevent the calculation error, the authors proposed a revised loss map method and proved the effectiveness of the method.