Improved quantum efficiency of Sr(Al,Si)5(O,N)7:Ce3+ by selection of Ce raw material

The luminescence properties of yellow-emitting Ce³⁺-doped Sr-containing sialon phosphor Sr(Al,Si)₅(O,N)₇:Ce³⁺ were notably improved by the Ce raw material selection. By changing the Ce raw material from oxides to nitrides or chlorides, the emission wavelength shifted to above 560 nm, which is beneficial for higher color rendering index white light-emitting diodes. This result from an increase in the covalency of the host crystal being associated with a decrease in the oxygen content. When Ce chloride was used, both the absorption and internal quantum efficiency increased, resulting in an increase in the external quantum efficiency up to 65%–72%. Inductively coupled plasma mass spectrometry, X-ray diffraction, and electron spin resonance measurements showed that the reason for the absorption increase is an increase in Ce³⁺ content and suppression of the generation of the second phase, and the reason for the increase in the internal quantum efficiency is a decrease in the host crystal absorption via suppression of anion vacancy generation. It was found that Ce chloride not only suppresses oxygen impurities but also acts as a flux that results in improved crystallinity.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

An improved method of phosphorus analysis in sea water

A reagent for the determination of phosphorus in sea water which contains Mo(VI) plus Mo(V) may be easily prepared by the reduction of Mo(VI) with metallic zinc in acid medium. This reagent is stable in the air for several months, and the development of the molybdenum blue colour is complete in 20 min at about 100°C; the colour is stable for at least a few months. The salt error is approximately 5 per cent with sea water of chlorinity 19 per milli. The interference due to either arsenate or silicate at their concentrations in sea water is negligible.     

Simple low-vacuum coating of paraffin wax on carbonaceous gas sensing layers

A simple low-vacuum coater has been fabricated by using a vacuum resin degassing chamber, in which an aluminum effusion cell is heated by a soldering iron. Our developed vacuum coater presents the versatile methods for depositing paraffin wax for skin-coating the sensing layers of quartz crystal microbalance (QCM). As the increase of the cell temperature, the thickness and inhomogeneity of the wax films were increased. Impedance analyses revealed that the energy dissipation of the QCM was remarkably enhanced with the amount of wax. It was also revealed that the as-deposited wax was fluidic until coagulation by heat radiation. This surface skin coating enhanced the ethyl acetate (EA) sorption capabilities of the polyethylene-sputtered QCM sensor, whereas, it reduced the EA sorption capacity of the d-phenylalanine-sputtered QCM sensor.     

Efficient and precise cutting of zirconia ceramics using heated cutting tool

The thermally assisted machining of yttria-stabilized tetragonal zirconia polycrystal using a cutting tool heated with induction heating was proposed. Although the conventional thermally assisted machining cannot be applied to drilling, the proposed method can be. Heat transfer from the heated cutting tool to the workpiece was simulated analytically, and the result showed that heating of the tool up to 500 °C produced an increase of 150–400 °C in the workpiece temperature. Cutting experiments demonstrated an improvement in machinability.     

Influence of temperature on the fatigue strength of compressed-hydrogen tanks for vehicles

The influence of environmental temperatures on the fatigue strength of compressed-hydrogen tanks for vehicles was investigated. The fatigue strength of Type-3 tanks was found to decrease in a low-temperature environment and increase in a high-temperature environment. The Type-3 tank has been subjected to autofrettage to improve fatigue strength. The investigation clarified that the effect of autofrettage changes according to the environmental temperature due to the difference between the coefficients of thermal expansion of carbon fiber reinforced plastic and aluminum alloy. This causes fatigue strength to change with changes in temperature. The Type-4 tank has a very long fatigue life and did not break after 45,000 cycles in a room-temperature or low-temperature environment. In a high-temperature environment, however, the tank broke in fewer than 45,000 cycles. The fatigue of carbon fiber reinforced plastic was promoted in the high-temperature environment, resulting in breakage of the tank. These results indicate that the fatigue strength of the tanks is influenced by the environmental temperature.     

Microscopic study on the polymorphism of Ca3SiO5

The polymorphism of Ca₃SiO₅ has been studied microscopically by following changes in optic properties and modes of twinning of the crystal as a function of temperature. Besides the six modifications already established, a hitherto-unidentified monoclinic phase M₃, which can be characterized only by microscopy at present, has been found to exist just below the rhombohedral phase (R). The transitions $\text{T}{}_2\text{?}\text{T}{}_3\text{et}\text{M}{}_1\text{?}\text{M}{}_2$ that give clear thermal effects on the DTA curve show no corresponding change under the microscope.     

Seeding effects on solidification behavior of cocoa butter and dark chocolate. I. Kinetics of solidification

Effects of seeding of fat crystals on the crystallization kinetics of cocoa butter and dark chocolate were examined with a rotational viscometer. The seed crystals employed were cocoa butter, 1,3-distearoyl-2-oleoylglycerol (SOS), 1,3-dibehenoyl-2-oleoylglycerol (BOB) and 1,2,3-tristearoylglycerol (SSS). The seed powders were prepared by pulverization below —50°C, the dimensions being in a range from 20–70 μm. Particular attention was paid to the influence of polymorphism of the seed crystal. We found that all of the above seed materials accelerated the crystallization, the degree of acceleration being in a following order; SOS (β ₁) > cocoa butter (Form V) > SOS (a mixture ofβ’ andβ ₂) > BOB (β ₂) > BOB (pseudo-β’) > SSS (β). Precise measurements of the crystallization kinetics showed that the most influential factors in the seeding effects are the physical properties of the seed materials—above all, thermodynamic stability, and similarity in the crystal structure to cocoa butter are the most determinative.     

Inhomogeneous compression of PEMFC gas diffusion layer: Part I. Experimental

This paper presents a study on the effect of inhomogeneous compression of gas diffusion layer (GDL) caused by the channel/rib structure of flow-field plate. The experimentally evaluated properties are GDL intrusion into the channel, gas permeability, in-plane and through-plane bulk electric conductivities, and contact resistances at interfaces as a function of compressed thickness of GDL. It was found that the GDL is compressed very little under the channel whereas GDL under the rib is compressed to gasket thickness. The compression of GDL reduces gas permeability and contact resistance, and improves bulk conductivity. Hence, the inhomogeneous compression of GDL may lead into significant local variation of mass and charge transport properties in the GDL. These effects have been ignored in most of the published modeling studies. This contribution, part I, covers the experimental setup and measurement results, and a model which takes the inhomogeneous compression of GDL into account is presented in part II.