Polymers beyond standard optical fibres – fabrication of microstructured polymer optical fibres

This paper reports the overall fabrication process of microstructured polymer optical fibres (mPOFs). mPOF fabrication involves a two‐step process: on the one hand, the design and creation of a preform containing a large‐scale version of the desired fibre and, on the other, the precise heating and drawing of the preform to the final fibre. The preforms are produced either by an improved drilling technique or by capillary stacking. For a correct and accurate drawing of the fibre, a controlled and precise heating unit has to be designed, an issue that will be explained in detail in this work. The quality and optical performance of the final mPOF depends strongly on key factors such as the preform annealing, the accuracy of the technique selected for the creation of the preform structure, the heating stage, as well as on the drawing parameters. All of them are analysed in detail and some drawn mPOFs of interest are reported as well. © 2018 Society of Chemical Industry     

Spray Drying of Lactobacillus plantarum WCFS1 Guided by Predictive Modeling

Shelf life of probiotic microorganisms can be retained by drying. Spray drying is an economically interesting alternative to freeze drying with that respect. However, the viability can decrease due to the drying process and testing it is laborious and expensive. This research shows that the viability of Lactobacillus plantarum WCFS1 during pilot scale drying can be predicted with kinetics gathered at a single droplet level. Using this approach, it could be demonstrated that the viability of L. plantarum WCFS1 during spray drying is mainly determined by the combination of temperature and moisture content during the first 0.5 seconds after atomization. The combination of a high moisture content and a high temperature appeared most detrimental to the residual viability. Moreover, it was found to be important to take into account the particle size distribution during atomization when predicting viability, since this has a large effect on the moisture content during this first 0.5 seconds. Finally, it was observed that shelf life during storage was mainly determined by the moisture content of the powder. A lower moisture content resulted in a higher viability. Above a moisture content of 6%, shelf life stability rapidly decreased in the applied maltodextrin (DE = 16) matrix.     

Cover Image,Volume 67, Issue 9

The cover image, by Eneko Arrospide et al., is based on the Review Polymers beyond standard optical fibres ‐ fabrication of microstructured polymer optical fibres, DOI: 10.1002/pi.5602 .

     

Mode coupling contribution to radiation losses in curvatures for high and low numerical aperture plastic optical fibers

We have studied the optical power losses due to multiple curvatures in polymethylmetacrylate (PMMA) plastic optical fibers (POFs) of different numerical apertures (NAs) and attenuation. The fibers were tested for several configurations in order to assess the influence of different types of curved-to-straight fiber transitions in the amount of power radiation. We found that losses are below the standards for all tested fiber types, and thus, they are a suitable choice for local area network (LAN) applications. In addition, our results revealed the presence of modal interactions as confirmed using an experimental procedure to estimate the mode coupling strength for the same fibers.     

Passive device based on plastic optical fibers to determine the indices of refraction of liquids

We have designed and measured a passive device based on plastic optical fibers (POF's) that one can use to determine the indices of refraction of liquids. A complementary software has also been designed to simulate the behavior of the device. We report on the theoretical model developed for the device, its implementation in a simulation software program, and the results of the simulation. A comparison of the experimental and calculated results is also shown and discussed.     

Mapping photovoltaic performance with nanoscale resolution

Photo‐conductive AFM spectroscopy (‘pcAFMs’) is proposed as a high‐resolution approach for investigating nanostructured photovoltaics, uniquely providing nanoscale maps of photovoltaic (PV) performance parameters such as the short circuit current, open circuit voltage, maximum power, or fill factor. The method is demonstrated with a stack of 21 images acquired during in situ illumination of micropatterned polycrystalline CdTe/CdS, providing more than 42 000 I/V curves spatially separated by ~5 nm. For these CdTe/CdS microcells, the calculated photoconduction ranges from 0 to 700 picoSiemens (pS) upon illumination with ~1.6 suns, depending on location and biasing conditions. Mean short circuit currents of 2 pA, maximum powers of 0.5 pW, and fill factors of 30% are determined. The mean voltage at which the detected photocurrent is zero is determined to be 0.7 V. Significantly, enhancements and reductions in these more commonly macroscopic PV performance metrics are observed to correlate with certain grains and grain boundaries, and are confirmed to be independent of topography. These results demonstrate the benefits of nanoscale resolved PV functional measurements, reiterate the importance of microstructural control down to the nanoscale for 'PV devices, and provide a widely applicable new approach for directly investigating PV materials. Copyright © 2015 John Wiley & Sons, Ltd.     

Evolution of Plastic Control Networks

Evolutionary Robotics is a powerful method to generate efficient controllers with minimal human intervention, but its applicability to real-world problems remains a challenge because the method takes long time and it requires software simulations that do not necessarily transfer smoothly to physical robots. In this paper we describe a method that overcomes these limitations by evolving robots for the ability to adapt on-line in few seconds. Experiments show that this method require less generations and smaller populations to evolve, that evolved robots adapt in a few seconds to unpredictable change-including transfers from simulations to physical robots- and display non-trivial behaviors. Robots evolved with this method can be dispatched to other planets and to our homes where they will autonomously and quickly adapt to the specific properties of their environments if and when necessary.