The activation of furfuryl alcohol polymerization by oxygen and its enhanced mechanical properties

The effect of oxygen and additional oxygen providers on furfuryl alcohol polymerization was investigated through chemical analyses and mechanical evaluation. NMR, UV–vis, Fourier transform infrared, and gas chromatography–mass spectrometry (GC–MS) results suggested that atmospheric oxygen and the further addition of an oxygen source functioned as an activator for the entire network polymerization. Interestingly, the construction of a conjugated structure on the furan linear chain, which is key to three-dimensional cross-linking, also appears to be accelerated in the presence of oxygen. Furthermore, the introduction of oxygen providers into the curing system successfully enhanced the mechanical properties of the cured furan resin.     

Tracking a Sea Turtle by an AUV with a Multibeam Imaging Sonar: Toward Robotic Observation of Marine Life

International Journal of Control, Automation and Systems - This paper proposes a method for autonomous underwater vehicles to chase sea turtles without attaching any tag to them, toward efficient...     

Water leakage due to the welding defect and improvement to reach 1-MW beam operation in the mercury target of J-PARC

ABSTRACT

Neutron flux per pulse reached world record at neutron source in Japan Proton Accelerator Research Complex (J-PARC). In the J-PARC, mercury target system is used as a spallation neutron source. A target vessel has a multi-walled protection system that comprises a mercury vessel enclosed with a double-walled water shroud. This is to prevent the leakage of the mercury outside the target vessel. The multi-walled structure needed to be complicated with a lot of welding lines. However, during the operation, we faced an unscheduled shutdown due to water leakage to the intermediate layer between the mercury vessel and water shroud. An investigation on the cause of the leakage was carried out. It is deduced that the leakage path was formed due to the crack propagation from welding defects that are caused by the complicated multi-walled structure. The crack propagation is attributed to the repeated stress by pressure waves generated in the mercury target. Based on the investigation results, the design was improved to remove the welding line on the complicated structure and to realize the stable operation with 1 MW proton beam, which is the final design value of the neutron source in J-PARC.     

Improvement in impact strength of modified cardanol‐bonded cellulose thermoplastic resin by adding modified silicones

The impact strength of cellulose diacetate (CDA) bonded with a modified cardanol (3‐pentadecylphenoxy acetic acid: PAA) was greatly improved up to 9 kJ/m² by adding a relatively small amount of modified silicones while suppressing a decrease in bending strength. In our recent research, this thermoplastic resin (PAA‐bonded CDA) exhibited high rigidity, glass transition temperature, and water resistance. However, its impact strength was insufficient for use in durable products. Therefore, silicones modified with polyether, amino, and epoxy groups were investigated as possible ways to improve the impact strength. The results show that adding polyether‐modified silicone (polyether silicone) with moderate polarity relative to PAA‐bonded CDA resulted in shearing deformation greatly enhances its impact strength while maintaining other properties, including glass transition temperature (T_g), water resistance, and thermoplasticity. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40366.     

Main‐chain smectic liquid crystalline polymer exhibiting unusually high thermal conductivity in an isotropic composite

The thermal conductivity (TC) of an isotropic composite comprising of a main‐chain smectic liquid crystalline PB‐10 polyester and 50‐μm‐sized roughly spherical magnesium oxide (MgO) particles is investigated. The increase in the composite TC with higher MgO fractions is steeper than that expected by Bruggeman's theory for the TC of a polydomain PB‐10 polyester (0.52 W m^?1 K^?1). When the filler content is larger than 30 vol %, the composite TC approaches a value that can be explained only if the polyester functions as a matrix with 1.0 W m^?1 K^?1, which is five times as high as those of isotropic common polymers (0.2 W m^?1 K^?1). Such an unusually high TC for a polymer matrix is attributed to some polymer lamellae that lie parallel to the particle surface and are stacked toward neighboring particles, thus creating effective heat paths between the particles and a continuous thermal network in a composite. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 39896.     

Improvement in impact strength of modified cardanol‐bonded cellulose thermoplastic resin by using olefin resins

Impact strength of a modified cardanol‐bonded cellulose thermoplastic resin was greatly improved by using a small amount of olefin resins. As we showed, this thermoplastic resin (3‐pentadecylphenoxy acetic acid (PAA)‐bonded cellulose diacetate (CDA): PAA‐bonded CDA) exhibited high practical properties such as bending strength, heat resistance, and water resistance. However, its impact strength was insufficient for use in durable products. We improved the impact strength of PAA‐bonded CDA by adding hydrophobic olefin resins, such as polyethylene or polypropylene, while maintaining good bending strength and breaking strain. Furthermore, the application of olefin resins also increased water resistance and fluidity. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39829.     

Synthesis of 4‐Aryl‐2‐Quinolones via Copper‐Catalyzed Hydroarylation of (o‐Aminophenyl)propiolates with Arylboronates

4‐Aryl‐2(1H)‐quinolones were efficiently synthesized via copper‐catalyzed hydroarylation of (o‐aminophenyl)propiolates with arylboronic acid neopentyl glycol esters. The substrate propiolates were prepared from the corresponding silylalkynes with carbon dioxide by Kondo’s carboxylation method using N,N‐dimethylformamide as a solvent. Hydroarylation was performed in the presence of 3 mol% copper(II) acetate in methanol at 28 °C for 12 h and subsequent deprotection using trifluoromethanesulfonic acid (3.0 equiv.) at 65 °C for 2 h in the same pot to afford the desired 4‐aryl‐2(1H)‐quinolones in 39–89% yields.

     

Structural Analysis of the Complex between Penta-EF-Hand ALG-2 Protein and Sec31A Peptide Reveals a Novel Target Recognition Mechanism of ALG-2

ALG-2, a 22-kDa penta-EF-hand protein, is involved in cell death, signal transduction, membrane trafficking, etc., by interacting with various proteins in mammalian cells in a Ca²⁺-dependent manner. Most known ALG-2-interacting proteins contain proline-rich regions in which either PPYPXnYP (type 1 motif) or PXPGF (type 2 motif) is commonly found. Previous X-ray crystal structural analysis of the complex between ALG-2 and an ALIX peptide revealed that the peptide binds to the two hydrophobic pockets. In the present study, we resolved the crystal structure of the complex between ALG-2 and a peptide of Sec31A (outer shell component of coat complex II, COPII; containing the type 2 motif) and found that the peptide binds to the third hydrophobic pocket (Pocket 3). While amino acid substitution of Phe⁸⁵, a Pocket 3 residue, with Ala abrogated the interaction with Sec31A, it did not affect the interaction with ALIX. On the other hand, amino acid substitution of Tyr¹⁸⁰, a Pocket 1 residue, with Ala caused loss of binding to ALIX, but maintained binding to Sec31A. We conclude that ALG-2 recognizes two types of motifs at different hydrophobic surfaces. Furthermore, based on the results of serial mutational analysis of the ALG-2-binding sites in Sec31A, the type 2 motif was newly defined.     

Practical Application of ±250‐kV DC‐XLPE Cable for Hokkaido–Honshu HVDC Link

The long‐term dc properties of DC‐XLPE insulation materials, which have been developed for dc use, were investigated. It was found that the lifetime of DC‐XLPE under dc voltage application is extended by the addition of nano‐sized filler. The time dependence of the space charge distribution at 50 kV/mm was observed for 7 days. Almost no accumulation of space charge in DC‐XLPE was found. The 250‐kV DC‐XLPE cables and accessories were manufactured and subjected to a type test and PQ test for use in the Hokkaido–Honshu dc link facility owned by the Electric Power Development Co., Ltd. These tests were performed under conditions that included a polarity reversal test for line commutated converter (LCC) systems as recommended in CIGRE TB 219. The test temperature was 90 °C. The type test and PQ test were successfully completed. The DC‐XLPE cable and accessories were installed in summer 2012 for the Hokkaido–Honshu dc link. After the installation of the dc extruded cable system, a dc high‐voltage test at 362.5 kV (=1.45 PU) for 15 min was successfully completed in accordance with CIGRE TB 219. This dc extruded cable system was put into operation in December 2012 as the world's highest‐voltage extruded dc cable in service and the world's first dc extruded cable for a LCC system including polarity reversal operation.