Predicting Tensile Properties of Friction-Stir-Welded 6063 Aluminum with Experimentally Measured Welding Heat Input

This work aims to develop a reliable method to predict mechanical properties of friction-stir-welded 6 xxx-series alloys with experimentally measured welding heat input. A calorimetrical method was utilized to experimentally measure the welding heat input in the friction stir welded of aluminum alloy 6063-T5. Good correlations between the input variables, i.e., welding parameters and physical properties of the materials, and the welding heat inputs obtained with experimental measurements were discovered. The welding heat input can be predicted using the empirical equation derived based on these correlations. Moreover, the results suggested that the thermal conductivities of the welded alloys affected the welding heat input significantly. Mechanical properties, including hardness and tensile properties, of friction-stir-welded aluminum alloy 6063 were in good correlation to the heat input obtained with experimental measurement. These correlations were explained by the evolution of the strengthening precipitates during welding. This work proposed a reliable new route to predict these mechanical responses through the estimation of heat input.     

Use of multivariate analysis for the improvement in prediction accuracy of bacterial aerobic plate count by flow cytometry

Flow cytometry (FCM) and aerobic plate count (APC) by the culture method were performed on green tea samples spiked with Escherichia coli type strain NCTC9001 (ATCC11775) solutions of different concentrations. In FCM, fluorescence signals from multiple stained bacteria and other fluorophores are detected using detector channels, and recorded as events with a voltage at each channel. FCM data were analyzed in two ways: conventional and multivariate analysis. In the former, the number of events with voltages larger than the defined threshold values was regarded as the predicted APC. In the latter, voltage histograms of all channels were obtained and merged horizontally to serve as explanatory variables. Then a partial least squares regression (PLSR) model was built to predict APC from the histogram data. The coefficient of determination (R²) and the root mean square error (RMSE) between APC by the culture method and that predicted by conventional FCM were 0.916 and 1.08 cfu/ml². The APC values predicted by the PLSR model and those measured were in good agreement with R² of 0.982 and RMSE of 0.417 cfu/ml, which verified the potential of the proposed method for improving APC prediction accuracy by FCM.     

An application of interpretive structural modelling to analyse preference structure in multiobjective dynamic environmental-economic systems†

This paper applies ISM (interpretive structural modelling) to analyse preference structure in a multiobjective problem of a dynamic environmental-economic model, and terms this method IPSM (interpretive preference structural modelling). Multi-objectives in the model include minimizing social cost of pollution, and maximizing total consumption in a planning interval. IPSM analyses decision-maker's preference relations (mental model) among many Pareto-optimal solutions of the multiobjective systems under the interactive cooperation between the decision-maker and the model-builder, and extracts the decision-maker's preference structure as a hierarchical directed graph, where the vertices of the graph correspond to the Pareto-optimal solutions and the directed edges correspond to the preference relations. An interesting economic interpretation for a preferred solution is discussed in terms of the economic interpretation of the discrete minimum principle.     

Spontaneous emission from a three-level atom placed in three-dimensional photonic crystals in the long-time limit

The paper describes the spontaneous emission from a three-level atom placed in a periodic dielectric microstructure which exhibits a complete three-dimensional photonic band gap. By using the Euler approach, the upper level population of the atom is calculated for a wide range of relationships between the Rabi frequency and the detuning of the atomic transition frequency from the upper band edge. The results indicate that there are three cases of the relationship between Rabi frequency and detuning, which determine distinctive states of the atomic population in the long-time limit. When the detuning is greater than the Rabi frequency, the upper level has a zero steady-state atomic population, which leads to enhancement of spontaneous emission. When the magnitude of the detuning is less than the Rabi frequency, the upper level has a nonzero steady-state atomic population, which leads to suppression of spontaneous emission. When the negative detuning is greater than the Rabi frequency, the upper level has a nondecaying oscillatory-state atomic population due to long-time atomic splitting. These three properties of the spontaneous emission are relevant to several optical devices on an atomic scale, such as optical memories, switches and clocks.     

Development of –1 MV DC Filter and High‐Voltage DC Measurement Systems for ITER NBI

This paper presents the development results of a ?1 MV dc filter and dc measurement systems for an ITER (International Thermonuclear Experimental Reactor) neutral beam injector (NBI) system. High accuracy of 0.5% and fast responsivity of 3.3 μs, ?3 dB are required for the dc measurement systems: both dc voltage dividers and DCCTs. Circuit design and thermal flow design were carried out to clarify and minimize their effects on the accuracy and responsivity. The validity of the established design was demonstrated by the actual‐product tests; temperature rise of each components fell below the allowable value; inner components of dc filter withstood dc ?1.2 MV; each voltage divider accurately measured the voltage during the dc ?1.2 MV withstand voltage test; the voltage dividers and the DCCTs were adequate to the requirements of responsivity (3.3 μs, ?3 dB).     

Invar36合金搅拌摩擦焊焊缝的低温韧性

为了研究Invar36合金搅拌摩擦焊焊缝的低温韧性,采用小冲杆试验方法（small punch test）对焊接速度2mm／s,搅拌头旋转频率200一1000r／min的Invar36合金焊缝进行低温（77K）和室温（298K）韧性测试．298K下,所有焊接工艺的焊缝小冲杆试验能均高于母材,焊缝韧性随搅拌头旋转频率的提...     

Synthesis of a stabilizing control problem for a multimachine power system with phase shifter

A systematic procedure is considered for the synthesis of a stabilizing control method for a multimachine power system with phase shifter, taking into account the velocity governor. A new approach is presented, which uses a coordinate-transformation technique and an optimization technique. The application of this method to a stabilizing control problem for a power system is illustrated by considering a 3-machine power system with phase-shifter control, taking into account an additional control vector for the governing system with one time constant. The synthesized controls are then used to improve the power-system transient stability to a remarkable degree and to restore the power-system transients rapidly to the stable-equilibrium point. Numerical results arc given.     

Microstructural analysis of the stir zone of Al alloy produced by friction stir spot welding

The present study applied friction spot joining (FSJ), which was recently developed as a lap joining technique of Al alloys, to two sheets of Al alloy 6061, 1 mm in thickness, and then examined the microstructural feature in the weld. The weld had the nugget-shaped stir zone around the exit hole of the probe, and the stir zone exhibited the equiaxed grain structure having finer grain size than that of the base material. The crystallographic texture analysis using electron backscattered diffraction method suggested that the material movement occurred along the rotating direction of the welding tool in the wide region including the stir zone. In the periphery of the nugget-shaped stir zone, which was characterized as the region having the finer grain size than that of the stir zone interior, any inclusions and precipitates were not found in the SEM scale. The weld was softened around the weld centre. The softening could be explained by dissolution and/or growth of the strengthening precipitates due to thermal cycle of FSJ.     

Degradation Kinetics and Storage Stability of Vacuum Spray-Dried Micro Wet-Milled Orange Juice (<Emphasis Type="Italic">Citrus unshiu</Emphasis>) Powder

The aim of this work was to evaluate the degradation kinetics and stability of micro wet milled orange juice powders obtained by vacuum spray drying, using maltodextrin as a carrier agent. Powders were produced with four combinations of orange juice solids/maltodextrin solids 60:40, 50:50, 40:60, and 30:70 by weight. Ascorbic acid degradation, color, and antioxidant activity of powders were evaluated throughout 90 days. Powders were stored at 10, 25, and 35 °C and relative humidity of 33%. Temperature and storage time negatively influenced the stability of ascorbic acid and color, whereas antioxidant activity increased at the beginning of storage at a higher temperature then decreased slightly after 60 days. For stability study, powders were stored at different water activities (0.11 to 0.84) in order to determine the plasticizing effects of water on glass transition temperature. Both water activity and glass transition temperature were used to predict the critical conditions for storage. Vacuum spray dried powder produced with a ratio of 30:70 (orange juice solids/maltodextrin solids) was considered as the most stable, since it showed highest critical water activity (a_w?=?0.61) and lowest moisture content (0.11 g water/g of dry solid) among the four powders. Vacuum spray drying using superheated steam as the heating medium was proven to be an effective way of producing orange juice powders with minimum loss of nutrients.