Electro-oxidation of dimethyl ether on Pt/C and PtMe/C catalysts in sulfuric acid

The electro-oxidation of dimethyl ether (DME) on PtMe/Cs (Me = Ru, Sn, Mo, Cr, Ni, Co, and W) and Pt/C electro-catalysts were investigated in an aqueous half-cell, and compared to the methanol oxidation. The addition of a second metal enhanced the tolerance of Pt to the poisonous species during the DME oxidation reaction (DOR). The PtRu/C electro-catalyst showed the best electro-catalytic activity and the highest tolerance to the poisonous species in the low over-potential range (<0.55 V, 50 °C) among the binary electro-catalysts and the Pt/C, but at the higher potential (>ca. 0.55 V, 50 °C), the Pt/C behaved better than PtRu/C. The apparent activation energy for the DOR decreased in the order: PtRu/C (57 kJ mol⁻¹) > Pt₃Sn/C (48 kJ mol⁻¹) ≈ Pt/C (46 kJ mol⁻¹). On the other hand, the activation energy for the MOR showed a different turn, decreased in the following order: Pt/C (43 kJ mol⁻¹) > Pt₃Sn/C (35 kJ mol⁻¹) ≈ PtRu/C (34 kJ mol⁻¹). The temperature dependence of the DOR was greater than that of the oxidation of methanol (MOR) on the PtRu/C.     

Evaluating a behavioral demand response trial in Japan: evidence from the summer of 2013

This paper presents results from a behavioral demand response trial targeted to both grid and residential peak hours, in which weekly feedback via paper-based reports, real-time feedback via an in-home display, 30-minute tiered rate, and email prompts are adopted to almost 230 residential customers of a condominium in Funabashi, a city located in Greater Tokyo. Through a randomized experiment, we find that the peak saving impact during grid peak hours (1–4 pm, weekdays only) was 11.6 %, given that all the four interventions provided all at once. In addition, the results show that the variation in peak saving effects by household characteristics exists, and the variation differs among packages of peak saving interventions. Furthermore, we analyzed how much informational elements in weekly reports are considered as useful by residential customers. These results suggest that feedback-based approaches for peak saving can promote households’ energy conservation behavior.     

Preparation method for supported metal catalysts using w/o microemulsion: Study on immobilization conditions of metal particles by hydrolysis of alkoxide

It was previously found that the silica-supported rhodium catalyst prepared using water-in-oil microemulsion had rhodium particles partly, or wholly, embedded in silica. In this work, consequently, we investigated the effect of hydrolysis conditions of tetraethylorthosilicate, employed as the source of silica, on the atomic ratio of surface rhodium in contact with the gas phase, to total surface rhodium of nanoparticles. This ratio is denoted as R in this paper. R became higher when the catalyst was prepared under the following hydrolysis conditions: a shorter hydrolysis time and a smaller amount of tetraethylorthosilicate. On the other hand, R showed the minimum value when the water content in the preparation solution was 33 vol%. From these results, it is demonstrated that it was important to form silica as early as possible in hydrolysis of TEOS in order to increase R values. In addition, the effect of R on the catalytic behavior in CO hydrogenation was investigated. At R values below 30%, the turnover frequencies increased with a decrease in R.     

Influence of sputtering power on oxygen reduction reaction activity of zirconium oxides prepared by radio frequency reactive sputtering

Zirconium oxides (ZrO_2−x) have been investigated as new cathodes for direct methanol fuel cells without platinum. ZrO_2−x films were prepared using a radio frequency (RF) magnetron sputtering at RF powers from 75 to 175 W. The influence of the RF power on the catalytic activity for the oxygen reduction reaction (ORR) and properties of the ZrO_2−x films were examined. The ORR activity of the ZrO_2−x catalyst increased with the RF power in the range we studied. The onset potential for ORR over ZrO_2−x deposited at 175 W was 0.88 V vs RHE. In addition, the relationship between the ORR activity and the composition, crystallinity, electric conductivity, as well as the ionization potential has been investigated. The zirconium oxide with an oxygen defected state and the higher electric conductivity showed the higher ORR activity, and the electrocatalytic activity for ORR increased with the decreasing in the ionization potential of the ZrO_2−x catalyst.     

Effect of Support Materials on the Selective Methanation of CO over Ru Catalysts

Selective methanation of CO in the reformate gas (CO/CO₂/H₂/H₂O = 0.175/17.9/70.9/11.1) proceeded over Ru catalysts supported on metal oxides and zeolites. CO was selectively methanated at wide temperature ranges (200–275 °C) over Ru/γ-Al₂O₃, Ru/TiO₂ Ru/H-Y and Ru/H-beta catalysts. Higher Ru contents in Ru/γ-Al₂O₃ improved the selective CO methanation rate.     

Cold repeated forming of compact for aluminium foam

A cold repeated forming process of compacts for producing metal foams was developed in order to strongly bond powder particles. In this process, the compact undergoes severe plastic deformation for the strong bonding of particles by repeated backward extrusion and cup compression, and thus the compact largely foams owing to the accumulation of gas released from blowing agents inside the compact during heating. The cold repeated forming process without heating is much simpler than that for the conventional hot extrusion process. The relative density of the foam was decreased by adding silicon powder to the compact, and an aluminium foam having a relative density of 0.27 was obtained using two repeats of backward extrusion and cup compression, 1.5 mass% titanium hydride powder and 4 mass% silicon powder. In addition, a one-piece foam was successively produced from the bonding of two compacts during the foaming in a die. It was found that the cold repeated forming of compacts is effective for the production of metal foams.     

Utilization of adzuki bean extract as a natural antioxidant in cured and uncured cooked pork sausages

A commercial adzuki bean extract (AE) was evaluated for antioxidant effectiveness in cured and uncured cooked pork sausages. TBARS values, instrumental color evaluation and sensory panel scores were assessed. For uncured sausages, AE at 0.2% was equally effective as 0.1% butylated hydroxytoluene (BHT) in reducing TBARS values. Similarly, AE at 0.2% significantly (P<0.01) reduced the TBARS in cured sausages. Incorporation of 0.2% AE into sausages produced higher (P<0.05) CIE lab color a* value and lower (P<0.05) L* and b* values. Sensory panels did not detect any difference in color, odor, taste, flavor, and overall acceptance in uncured pork sausages with addition of 0.2% AE. However, there were adverse changes in the color and odor of cured sausages, even though the taste, flavor, and overall acceptance were similar. Therefore, the results suggest that AE is a potential antioxidant.     

Improvement of characteristics of new-type solar cells, having a “transparent conductor/thin Si02 layer with ultrafine metal particles as conductive channels/n-Si” junction

New-type solar cells, having a structure “transparent conductor/thin Si0₂ layer with ultrafine metal islands as conductive channels/n-Si” have been prepared by forming a very thin (< 1.0 nm) silicon oxide (Si0₂) layer as well as platinum (Pt) islands (5–50 nm in size) embedded in it on a single crystal n-type silicon (n-Si) wafer, followed by the deposition of an indium tin oxide (ITO) film (200 nm thick) by the electron-beam evaporation method. The open-circuit photovoltages (V_oc) of the solar cells of the above structure were relatively low, 0.25–0.47 V, but they increased very much to 0.50–0.59 V if a thin (3–10 nm) layer of an organic compound such as copper phthalocyanine (CuPc) was pre-deposited on the Pt-island modified n-Si wafer before the ITO deposition. The reason for the beneficial effect of the pre-deposition of the thin CuPc layer was investigated in detail, and it has been found that certain crystal defects are formed in n-Si near the n-Si/Si0₂ interface during the ITO deposition in the absence of the CuPc layer. The formation of such defects is prevented in the presence of the CuPc layer, which leads to a decrease in surface carrier recombination and hence to the increase in V_oc.     

Nanoimprinting using release-agent-coated resins

A fluorinated self-assembled monolayer (F-SAM) is mainly used as the antisticking layer. To prevent the F-SAM coated on the nanoimprint lithography (NIL) mold from deteriorating, we propose a new form of nanoimprinting using a release-agent-coated resin. The results from measuring the surface free energy and observations by scanning probe microscopy (SPM) confirmed that the surface free energy, frictional force, and adhesion force of the release-agent spray-coated polymethylmethacrylate (PMMA) were lower than those of PMMA. To prove the release-agent spray-coated PMMA had a releasing effect, we tried to undertake thermal nanoimprinting on it using a mold without F-SAM. The pattern was clearly imprinted on the resin without any signs of adhesion.